Cytotoxic and mutagenic evaluation of extracts from plant species of the Miconia genus and their influence on doxorubicin-induced mutagenicity: An in vitro analysis

The Miconia genus, a plant widely used for medicine, occurs in tropical America and its extracts and isolated compounds have demonstrated antibiotic, antitumoral, analgesic and antimalarial activities. However, no study concerning its genotoxicity has been conducted and it is necessary to determine its potential mutagenic effects to develop products and chemicals from these extracts. This study assessed the cytotoxicity, mutagenicity and the protective effects of methanolic extracts from Miconia species on Chinese hamster lung fibroblast cell cultures (V79). The cytotoxicity was evaluated using a clonogenic assay. Cultures exposed to the extract of Miconia albicans up to a concentration of 30 mu g/mL, M. cabucu up to 40 mu g/mL, M. albicans up to 40 mu g/mL and M. stenostachya up to 60 mu g/mL exhibited a cytotoxic effect on the cells. The clonogenic assay used three non-cytotoxic concentrations (5, 10 and 20 mu g/mL) to evaluate mutagenicity and antimutagenicity of the extracts. Cultures were treated with these three extract concentrations (mutagenicity test) or the extract associated with doxorubicin (DXR) (antimutagenicity test) in three protocols (pre-, simultaneous and post-treatments). Distilled water and DXR were used as negative and positive controls, respectively. In the micronucleus (MN) test, a significant reduction was observed in MN frequency in cultures treated with DXR and extracts compared to those receiving only DXR; a significant reduction was also observed for the presence of mutagenicity in all treatments. This study confirmed the safe use of Miconia extracts at the concentrations tested and reinforced the therapeutic properties previously described for Miconia species by showing their protective effects on doxorubicin-induced mutagenicity. (C) 2010 Elsevier GmbH. All rights reserved.

Water deficit and ABA application on leaf gas exchange and flavonoid content in marigold (Calendula officinalis L.)

Water deficit and ABA application on leaf gas exchange and flavonoid content in marigold (Calendula officinalis L.).The goal of this study was to evaluate the effects of water deficit and abscisic acid (ABA) application on physiological parameters and flavonoid production in marigold plant. The experiment was performed under nursery conditions with potted plants. It was tested water deficit by withholding water (control - diary irrigation, 3, 6 and 9 days without irrigation) followed by 3 ABA concentrations (0, 10 e 100 mu M) applied in the beginning of blooming. It was evaluated the relative water content and the leaf gas exchange using a portable infrared gas analyzer (A: net photosynthesis, gs: stomatal conductance, E: transpiration, Ci: CO(2) intercellular concentration and EUA: water use efficiency). At the end of 9 days of water deficit there were significant decreases in all the characteristics evaluated, independent of ABA application. This suggests that the main effect of ABA was to cause a reduction on gs which was accompanied of a reduction in A, only when the plants were submitted to the water deficit. There was no significant difference among the levels of water deficit tested in relation to the total flavonoid content in inflorescences. However, ABA restricted the flavonoids biosynthesis both in control plant and stressed plants.

Characterization of a chromium-rich tannery waste and its potential use in ceramics

Leather industries which promote hide stabilization by the conventional chrome-tanning process are a major source of pollution because of the resultant chromium-rich wastes. In this work, an extensive characterization of such a chromium-rich waste sludge is presented, regarding its chemical composition (XRF), crystalline phase contents (XRD), organic carbon content (TOC), thermal behavior by thermogravimetry (TG) and differential scanning calorimetry (DSC), as well as its stability under chemical attack (the concentration of important ions in the leachates being determined by capillary electrophoresis) and when submitted to temperatures as high as 1100 degrees C, in air. The material showed the tendency to produce some undesirable, and previously non-detected hexavalent chromium when exposed to high temperatures, but after washing off the soluble salts and the elimination of the organic matter by firing, the resultant material was succesfully tested as a ceramic pigment in a conventional glaze composition usually employed in the ceramic the industry. (C) 2009 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Effect of different surface treatments on the repair bond strength of indirect composites

Purpose: To evaluate the tensile bond strength of indirect composites repaired with different surface treatments and direct composites. Methods: 180 specimens were prepared with Targis, belleGlass HP and Sculpture indirect composites, light-activated and post-cured according to the manufacturers` recommendations. The specimens were stored in distilled water for 24 hours at 37 degrees C. The bonding surfaces were prepared with air abrasion, hydrofluoric acid or hydrofluoric acid followed by a neutralizing solution. All the treated surfaces were subject to the application of a silane and a bonding agent before the repair procedures with Tetric Ceram and Tetric Flow for the Targis specimens, Herculite XRV and Revolution for the belleGlass HP specimens and Sculp-It and Flow-It for Sculpture specimens. The tensile bond strength tests were carried out using a universal testing machine at cross-head speed of 0.5 mm/minute. The type of fracture was observed under a light microscope at x40 magnification. Data were analyzed by a two-way ANOVA and Tukey`s post-hoc tests (P<0.05). Results: Targis showed a statistically higher repair bond strength than belleGlass HP and Sculpture, which were not significantly different from each other. Air abrasion increased the repair bond strength of belleGlass HP and Sculpture. For Targis, all the surface treatments resulted in similar repair bond strength. The different viscosity of repair composites did not affect the repair of indirect composites. Fractured surfaces showed mostly adhesive failures, mainly with hydrofluoric acid treatment.