Porcine skin as a source of biodegradable matrices: alkaline treatment and glutaraldehyde crosslinking

In this work, the modifications promoted by alkaline hydrolysis and glutaraldehyde (GA) crosslinking on type I collagen found in porcine skin have been studied. Collagen matrices were obtained from the alkaline hydrolysis of porcine skin, with subsequent GA crosslinking in different concentrations and reaction times. The elastin content determination showed that independent of the treatment, elastin was present in the matrices. Results obtained from in vitro trypsin degradation indicated that with the increase of GA concentration and reaction time, the degradation rate decreased. From thermogravimetry and differential scanning calorimetry analysis it can be observed that the collagen in the matrices becomes more resistant to thermal degradation as a consequence of the increasing crosslink degree. Scanning electron microscopy analysis indicated that after the GA crosslinking, collagen fibers become more organized and well-defined. Therefore, the preparations of porcine skin matrices with different degradation rates, which can be used in soft tissue reconstruction, are viable.

Mechanical, thermal and morphological properties of glutaraldehyde crosslinked bovine pericardium followed by glutamic acid treatment

Major problems with valve bioprostheses are associated with progressive structural deterioration and calcification, directly associated with the use of glutaraldehyde (GA). This work describes the effects of GA processing and borate/glutamic acid buffer treatment on the mechanical, thermal and morphological properties of 0.5% GA crosslinked bovine pericardium (BP). The results showed that while the treatment of 0.5% GA crosslinked BP with borate/glutamic acid significantly improves the mechanical properties, it had no visible effect on surface morphology. Better surface preservation was only achieved for BP pre-treated with a lower GA concentration followed by the conventional treatment (0.5% GA). Improvements in mechanical properties probably arises from structural changes probably involving the depolymerization of polymeric GA crosslinks and an increase electrostatic interaction due to covalent binding of glutamic acid to free carbonyl groups (Schiff base).The results indicate that the treatment GA crosslinked BP with borate/glutamic acid buffer may be an attractive procedure for the manufacture of heart valve bioprostheses.

Photodynamic antimicrobial chemotherapy (PACT) for the treatment of malaria, leishmaniasis and trypanosomiasis

A photodynamic effect occurs when photosensitiser molecules absorb light and dissipate the absorbed energy by transferring it to biological acceptors (usually oxygen), generating an excess of reactive species that are able to force cells into death pathways. Several tropical diseases present physiopathological aspects that are accessible to the application of a photosensitiser and local illumination. In addition, disease may be transmitted through infected blood donations, and many of the aetiological agents associated with tropical diseases have been shown to be susceptible to the photodynamic approach. However, there has been no systematic investigation of the application of photoantimicrobial agents in the various presentations, whether to human disease or to the disinfection of blood products or even as photo-insecticides. We aim in this review to report the advances in the photoantimicrobial approach that are beneficial to the field of anti-parasite therapy and also have the potential to facilitate the development of low-cost/high-efficiency protocols for underserved populations.

Effect of experimental heat treatment on mechanical properties of resin composites

The aim of this study was to verify the influence of an experimental heat treatment (170ºC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5% significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

Validação e reprodutibilidade de uma escala de auto-eficácia para adesão ao tratamento anti-retroviral em pais ou cuidadores de crianças e adolescentes vivendo com HIV/AIDS

OBJETIVO: Validar uma escala de auto-eficácia para adesão ao tratamento anti-retroviral em crianças e adolescentes com HIV/AIDS, levando em consideração a perspectiva dos pais/responsáveis, e avaliar a sua reprodutibilidade. MÉTODOS: O estudo foi realizado no Hospital-Dia do Centro de Referência e Treinamento em DST/AIDS de São Paulo. Foram entrevistados os pais/responsáveis de 54 crianças e adolescentes de 6 meses a 20 anos que passaram em consulta de rotina pelo serviço. Os dados de auto-eficácia foram levantados pela escala de auto-eficácia para seguir prescrição anti-retroviral (AE), que foi calculada de duas maneiras: análise fatorial e fórmula já definida. A consistência interna da escala foi verificada pelo coeficiente ade Cronbach. A validade foi avaliada pela comparação das médias dos escores entre grupos de pacientes aderentes e não aderentes ao tratamento anti-retroviral (teste de Mann-Whitney) e cálculo do coeficiente de correlação de Spearman entre os escores e parâmetros clínicos. A reprodutibilidade foi verificada por meio do teste de Wilcoxon, pelo coeficiente de correlação intraclasse (CCI) e pelo gráfico de Bland-Altman. RESULTADOS: A escala de AE apresentou boa consistência interna (a= 0,87) e boa reprodutibilidade (CCI = 0,69 e CCI = 0,75). Quanto à validade, a escala de AE conseguiu discriminar pacientes aderentes e não aderentes ao tratamento anti-retroviral (p = 0,002) e apresentou correlação significativa com a contagem de CD4 (r = 0,28; p = 0,04). CONCLUSÕES: A escala de AE pode ser utilizada para avaliar a adesão à terapia anti-retroviral em crianças e adolescentes com HIV/AIDS, levando em consideração a perspectiva dos pais/cuidadores.

Nutritional aspects of the prevention and treatment of osteoporosis

Osteoporosis is a global health problem characterized by low bone mass and microarchitectural deterioration of bone tissue with a consequent increase in bone fragility and susceptibility to fracture. Nutrition plays a critical role in reducing the risk of osteoporosis through its effect on all of these fragility factors, especially on the development and maintenance of bone mass. An adequate calcium, vitamin D and protein intake resulted in reduced bone remodeling, better calcium retention, reduced age-related bone loss, and reduced fracture risk. Recent evidence indicates that a healthy dietary pattern including dairy products (mainly fat free), fruit and vegetables and adequate amounts of meat, fish and poultry is positively related to bone health. Furthermore, mineral and vitamin supplementation should be closely monitored by health professionals since it could have adverse effects and be insufficient to ensure optimal protection of bone health.

Nutrional aspects of the prevention and treatment of osteoporosis

A osteoporose é um problema de saúde global, caracterizada por baixa massa óssea e deterioração da microarquitetura do tecido ósseo, com consequente aumento da fragilidade óssea e suscetibilidade a fraturas. A nutrição desempenha um papel fundamental na redução do risco de osteoporose por seu efeito sobre todos os fatores relacionados à fragilidade óssea, principalmente no desenvolvimento e na manutenção da massa óssea. Uma adequada ingestão de cálcio, vitamina D e proteína leva à redução da remodelação óssea, à maior retenção de cálcio, à redução da perda óssea relacionada à idade e à redução do risco de fraturas. Evidências recentes indicam que uma alimentação saudável, incluindo a ingestão de produtos lácteos (principalmente os desnatados), frutas e verduras, e uma quantidade adequada de carnes, peixes e aves, está relacionada positivamente com a saúde óssea. Além disso, a suplementação de vitaminas e minerais deve ser monitorada de perto, por profissionais de saúde, uma vez que pode ter efeitos adversos e ser insuficiente para assegurar uma eficaz proteção à saúde óssea

Evaluation of timing and responses to physiotherapeutic treatment

In several treatment regimens, the recognition of chronobiology contributes to the therapeutic process through the effective use of temporization protocols. The purpose of the present study was to evaluate the relationship between the tic treatment and the time of day when such treatment was performed, as well as the chronotype of orthopedic and rheumatologic patients in a clinical physiotherapy school. The population studied was treated in the morning and evening periods. The patients were divided into three groups of pathologies with similar treatments, which were as follows: syndrome of shoulder impact (n=33), knee artrosis (n=17), and lombalgia (n=23). At the end of ten treatment sessions, data concerning pain, percentage of subjective improvement, chronotype and age were compared. At the end of the study, it was observed that the time of day when treatment was performed influenced the results of individuals treated in the evenings but had no influence on the individuals treated in the morning. In addition, the evening schedule was the most well suited for intermediate individuals.

Influence of Annealing Heat Treatment and Cr, Mg, and Ti Alloying on the Mechanical Properties of High-Silicon Cast Iron

The influence of annealing on the mechanical properties of high-silicon cast iron for three alloys with distinct chromium levels was investigated. Each alloy was melted either with or without the addition of Ti and Mg. These changes in the chemical composition and heat treatment aimed to improve the material's mechanical properties by inhibiting the formation of large columnar crystals, netlike laminae, precipitation of coarse packs of graphite, changing the length and morphology of graphite, and rounding the extremities of the flakes to minimize the stress concentration. For alloys with 0.07 wt.% Cr, the annealing reduced the impact resistance and tensile strength due to an enhanced precipitation of refined carbides and the formation of interdendritic complex nets. Annealing the alloys containing Ti and Mg led to a decrease in the mechanical strength and an increase in the toughness. Alloys containing approximately 2 wt.% Cr achieved better mechanical properties as compared to the original alloy. However, with the addition of Ti and Mg to alloys containing 2% Cr, the chromium carbide formation was inhibited, impairing the mechanical properties. In the third alloy, with 3.5 wt.% of Cr additions, the mechanical strength improved. The annealing promoted a decrease in both hardness and amount of iron and silicon complex carbides. However, it led to a chromium carbide formation, which influenced the mechanical characteristics of the matrix of the studied material.

Health services performance for TB treatment in Brazil: a cross-sectional study

Background: Researches to evaluate Primary Health Care performance in TB control in Brazil show that different cities aggregate local specificities in the dynamics of coping with the disease. This study aims to evaluate health services' performance in TB treatment in cities across different Brazilian regions. Methods: This cross-sectional study was conducted in five cities that are considered priorities for TB control in Brazil: Itaborai (ITA), Ribeirao Preto (RP) and Sao Jose do Rio Preto (SJRP) in the Southeast; Campina Grande (CG) and Feira de Santana (FS) in the Northeast. Data were collected through interviews with 514 TB patients under treatment in 2007, using the Primary Care Assessment Tool adapted for TB care in Brazil. Indicators were constructed based on the mean response scores (Likert scale) and compared among the study sites. Results: ""Access to treatment"" was evaluated as satisfactory in the Southeast and regular in the Northeast, which displayed poor results on 'home visits' and 'distance between treatment site and patient's house'. ""Bond"" was assessed as satisfactory in all cities, with a slightly better performance in RP and SJRP. ""Range of services"" was rated as regular, with better performance of southeastern cities. 'Health education', 'DOT' and 'food vouchers' were less offered in the Northeast. ""Coordination"" was evaluated as satisfactory in all cities. ""Family focus"" was evaluated as satisfactory in RP and SJRP, and regular in the others. 'Professional asking patient's family about other health problems' was evaluated as unsatisfactory, except in RP. Conclusions: Two types of obstacles are faced for health service performance in TB treatment in the cities under analysis, mainly in the Northeast. The first is structural and derives from difficulties to access health services and actions. The second is organizational and derives from the way health technologies and services are distributed and integrated. Incentives to improve care organization and management practices, aimed at the integration of primary, secondary and tertiary services, can contribute towards a better performance of health services in TB treatment.

EFFECTS OF THERMAL TREATMENT ON THE PHYSICOCHEMICAL CHARACTERISTICS OF GIANT BAMBOO

Despite countless use possibilities for bamboo, this material has two major disadvantages. One drawback is the low natural durability of most bamboo species due to presence of starch in their parenchyma cells. The other equally important drawback is the tendency bamboo has to present dimensional variations if subjected to environmental change conditions. In an attempt to minimize these inconveniences, strips (laths) of Dendrocalamus giganteus Munro were taken from different portions of the culm and subjected to several temperatures, namely 140 degrees C, 180 degrees C, 220 degrees C, 260 degrees C and 300 degrees C under laboratory conditions, at the ESALQ-USP college of agriculture. The thermal treatment process was conducted in noninert and inert atmospheres (with nitrogen), depending on temperature Specimens were then subjected to physicomechanical characterization tests in order to determine optimum thermal treatment conditions in which to preserve to the extent possible the original bamboo properties. Results revealed that there is an optimum temperature range, between 140 degrees and 220 degrees C, whereby thermally treated bamboo does not significantly lose its mechanical properties while at the same time showing greater dimensional stability in the presence of moisture.

Alkaloids from Stems of Esenbeckia leiocarpa Engl. (Rutaceae) as Potential Treatment for Alzheimer Disease

Esenbeckia leiocarpa Engl. (Rutaceae), popularly known as guaranta, goiabeira, is a native tree from Brazil. Bioactivity-guided fractionation of the ethanol stems extract afforded the isolation of six alkaloids: leiokinine A, leptomerine, kokusaginine, skimmianine, maculine and flindersiamine. All isolated compounds were tested for acetyl cholinesterase inhibition, in vitro and displayed anticholinesterasic activity. The alkaloid leptomerine showed the highest activity (IC(50) = 2.5 mu M), similar to that of the reference compound galanthamine (IC(50) = 1.7 mu M). The results showed for the first time the presence of alkaloids leptomerine and skimmianine in E. leiocarpa (Engl.) with potent anticholinesterasic activity.

Evaluation of the spouted bed dried leaf extract of Bauhinia forficata for the treatment of experimental diabetes in rats

Previously, we have demonstrated that treatment of experimental diabetes with a decoction of Bauhinia forficata leaves is beneficial. In this study, we prepared a two-fold concentrate of this extract and tested its effects on physiological, biochemical and toxicity markers in streptozotocin-diabetic rats. Dried and ground leaves were extracted with warm 70% hydroethanol and the filtrate concentrated by evaporation at 50 degrees C. This solution was mixed with colloidal silicon dioxide (Tixosil-333 (R)) and dried in a spouted bed (BfT). Rats were treated with water, insulin and Tixosil particles at low or high doses, alone or coated with dried BfT. Animals were periodically weighed and monitored for water and food intake; urinary volume, glucose, urea and protein; blood glucose, serum lipids, liver toxicity markers transaminase and phosphatase and masses of adipose tissue and skeletal muscle. Insulin treatment gave best rat growth and lowest values for all other markers. No other treatment affected any diabetic marker, but the enzyme activities were changed by diabetes and BfT. Thus, BfT toxicity could arise from secondary products of plant constituents or Tixosil interaction. Therefore, BfT prepared in the spouted bed as described, is unsuitable for treatment of diabetes, which implies that the method of preparation of any medicine is critical for its efficacy and toxicity.

Socioeconomic Differences in Preferences and Willingness-to-Pay for Insulin Delivery Systems in Type 1 and Type 2 Diabetes

Background: An evaluation of patients' preferences is necessary to understand the demand for different insulin delivery systems. The aim of this study was to investigate the association between socioeconomic status (SES) and patients' preferences and willingness to pay (WTP) for various attributes of insulin administration for diabetes management. Methods: We conducted a discrete choice experiment (DCE) to determine patients' preferences and their WTP for hypothetical insulin treatments. Both self-reported annual household income and education completed were used to explore differences in treatment preferences and WTP for different attributes of treatment across different levels of SES. Results: The DCE questionnaire was successfully completed by 274 patients. Overall, glucose control was the most valued attribute by all socioeconomic groups, while route of insulin delivery was not as important. Patients with higher incomes were willing to pay significantly more for better glucose control and to avoid adverse events compared to lower income groups. In addition, they were willing to pay more for an oral short-acting insulin ($Can 71.65 [95% confidence interval, $40.68, $102.62]) compared to the low income group ($Can 9.85 [95% confidence interval, 14.86, 34.56; P < 0.01]). Conversely, there were no differences in preferences when the sample was stratified by level of education. Conclusions: This study revealed that preferences and WTP for insulin therapy are influenced by income but not by level of education. Specifically, the higher the income, the greater desire for an oral insulin delivery system, whereas an inhaled route becomes less important for patients.