Quartz recrystallization regimes, c-axis texture transitions and fluid inclusion reequilibration in a prograde greenschist to amphibolite facies mylonite zone (Ribeira Shear Zone, SE Brazil)

The crystal-plastic behavior of quartz mylonites from the Ribeira Shear Zone (SE Brazil), a major strike-slip structure that was active during a prograde metamorphic phase related to the Neoproterozoic Brasiliano-Pan African Orogeny, was investigated using a multi-method approach. Geothermobarometry results indicate deformational conditions ranging from similar to 300 to similar to 630 degrees C and 500-700 MPa. A strong correlation between mapped metamorphic zones and a dominance of different dynamic recrystallization mechanisms of quartz occurs within the mylonite zone. Bulging recrystallization (BLG) dominates within the chlorite zone between 300 and 410 degrees C, subgrain rotation recrystallization (SGR) operates within the biotite zone from 410 to 520 degrees C, and grain boundary migration recrystallization (GBM) dominates in the garnet zone above 520 degrees C. The development of quartz c-axis textures is mainly governed by temperature and dynamic recrystallization mechanisms. Textures from BLG zone mylonites are characterized by maxima around Z; SGR zone mylonites display single girdles or asymmetric type I crossed girdles; and GBM zone mylonites comprise maxima around Y and intermediate between X and Z. The scarcity or absence of water-bearing fluid inclusions in quartz mylonites from the SGR and GBM zones, which are dominated by carbonic inclusions, suggests water-deficient conditions, whereas BLG zone mylonites are dominated by water-bearing inclusions. This evidence indicates that water was available in the protoliths but has been eliminated with increasing deformation and deformation temperature. No effect of the water content variation on the quartz microstructural and recrystallized grain size evolution was detected, and little influence on c-axis texture development was observed. Most of the fluid inclusion densities were reequilibrated during the shear zone exhumation history, recording a decompression in the range of 300-500 MPa, while microstructural reequilibration effects related to the prograde metamorphism are largely preserved. Fluid inclusion microstructures and densities from two SGR zone samples preserved evidence for a near isothermal compression within the interior of the Ribeira Shear Zone during the prograde metamorphism. (C) 2009 Elsevier B.V. All rights reserved.

Cambrian mafic to felsic magmatism and its connections with transcurrent shear zones of the Borborema Province (NE Brazil): Implications for the late assembly of the West Gondwana

New U-Pb (SHRIMP) and (40)Ar/(39)Ar isotopic data of igneous rocks and mylonites of the Borborema Province (NE Brazil) show that a wide range of tectonothermal events affected the province during the transition from the Precambrian to the Cambrian. Concordant zircon U-Pb data constrained the crystallization age of mafic stocks, mafic to felsic dikes and granite batholiths between 548 and 533 Ma. These bodies were emplaced in a regional strain field combining extension and dextral shearing. The ductile shear deformation overprinted an older basement fabric to develop a low- to medium metamorphic grade vertical mylonite belt that cut the province in the E-W direction. Magnetic fabrics of the Cambrian batholiths determined by anisotropy of magnetic susceptibility are consistent with syntectonic emplacement. The magmatic pulses and shear deformation would have supplied enough heat to reset the synkinematic micas of mylonites to yield (40)Ar/(39)Ar plateau cooling ages between ca. 550 and 510 Ma. These results provide evidence that emplacement of Early Cambrian mafic and felsic magmas were accompanied by regional-scale shear deformations, probably in the consequence of late collisions along the West Gondwana margin. (C) 2010 Published by Elsevier B.V.

Fabrics of pre- and syntectonic granite plutons and chronology of shear zones in the Eastern Borborema Province, NE Brazil

We used the fabrics of two granite plutons and U/Pb (SHRIMP) zircon ages to constrain the tectonic evolution of the E-trending Patos shear zone (Borborema Province, NE Brazil). The pre-tectonic Teixeira batholith consists of an amphibole leucogranite locally with aegirine-augite. Zircons from a syenogranite yielded crystallization ages of 591 +/- 5 Ma. The batholith fabrics were determined by anisotropy of magnetic susceptibility (AMS) and mineral shape preferred orientation. The fabrics support pre-transcurrent batholith emplacement, as evidenced by: (i) magmatic/magnetic fabrics in low susceptibility (<0.35 mSI) leucogranites highly discordant to the regional host rock structure, and (ii) concordant magnetic fabrics restricted to high susceptibility (>1 mSI) corridors connected to shear zones branching off from Patos. One of these satellite shear zones controlled the syntectonic emplacement of the Serra Redonda pluton, which yields a crystallization age of 576 +/- 3 Ma. This late shearing event marks the peak regional deformation that, south of Patos, was coupled to crustal shortening nearly perpendicular to the shear belt. The chronology of the deformational events indicates that the major shear zones of the eastern Borborema are late structures active after the crustal blocks amalgamated. (C) 2007 Elsevier Ltd. All rights reserved.

Cassava bagasse cellulose nanofibrils reinforced thermoplastic cassava starch

Cellulose cassava bagasse nanofibrils (CBN) were directly extracted from a by-product of the cassava starch (CS) industry, viz. the cassava bagasse (CB), The morphological structure of the ensuing nanoparticles was investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), presence of other components such as sugars by high performance liquid chromatography (HPLC), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) experiments. The resulting nanofibrils display a relatively low crystallinity and were found to be around 2-11 nm thick and 360-1700 nm long. These nanofibrils were used as reinforcing nanoparticles in a thermoplastic cassava starch matrix plasticized using either glycerol or a mixture of glycerol/sorbitol (1:1) as plasticizer. Nanocomposite films were prepared by a melting process. The reinforcing effect of the filler evaluated by dynamical mechanical tests (DMA) and tensile tests was found to depend on the nature of the plasticizer employed. Thus, for the glycerol-plasticized matrix-based composites, it was limited especially due to additional plasticization by sugars originating from starch hydrolysis during the acid extraction. This effect was evidenced by the reduction of glass vitreous temperature of starch after the incorporation of nanofibrils in TPSG and by the increase of elongation at break in tensile test. On the other hand, for glycerol/sorbitol plasticized nanocomposites the transcrystallization of amylopectin in nanofibrils surface hindered good performances of CBN as reinforcing agent for thermoplastic cassava starch. The incorporation of cassava bagasse cellulose nanofibrils in the thermoplastic starch matrices has resulted in a decrease of its hydrophilic character especially for glycerol plasticized sample. (C) 2009 Elsevier Ltd. All rights reserved.