Oxidation and abrasive wear of Fe-Si and Fe-Al intermetallic alloys

In the present work, intermetallic alloys Fe-Si and Fe-Al (Fe(3)Si-C-Cr and Fe(3)Al-C), produced by induction melting, were evaluated regarding their oxidation and abrasive resistance. The tests performed were quasi-isothermal oxidation, cyclic oxidation, and dry sand/rubber wheel abrasion. As reference, the ASTM A297-HH grade stainless steel was tested in the same conditions. In the oxidation tests, the Fe-Al based alloy presented the lowest oxidation rate, and the Fe-Si based alloy achieved the best results in the abrasion test, showing better performance than the HH type stainless steel.

Effect of binders and surface finish on wear resistance of HVOF coatings

The high velocity oxygen fuel (HVOF) thermal spray process produces highly wear and/or corrosion resistant coatings. Tungsten carbide with a metallic binder is often used for this purpose. In this work, tungsten carbide coatings containing cobalt or nickel binder were produced by HVOF and characterised by optical and electron microscopy, hardness and a dry sand/rubber wheel abrasion test. The HVOF process produced dense coatings with low porosity levels and high hardness. The wear resistance of the specimens, which were surface treated, increased as the roughness percentage decreased. Tungsten carbide nickel based coating yielded the best wear resistance in the as sprayed condition. However, the wear rate and wear of the two coatings converged to the same values as the number of revolutions increased. Wear behaviour in the ground condition was similar, although the tungsten carbide cobalt based coating yielded better performance with increasing distance travelled during the wear test.

Collapse behavior of soil in a Brazilian region affected by a rising water table

Collapsible soils are usually nonsaturated, low density, and metastable-structured soils that are known to exhibit a volume reduction following an episode of moisture increase or suction reduction. This paper describes the collapsible behavior of clayey sand based on controlled soil suction tests carried out on undisturbed samples from the city of Pereira Barreto, in the State of Sao Paulo, Brazil. Foundation settlements due to soil collapse are common in this region and occurred during the filling of the reservoir of the Tres Irmaos Dam, which induced the elevation of the groundwater table in different parts of Pereira Barreto. This paper shows that collapse strains depend on the stress and soil suction acting in the sample and that saturation is not necessary for a collapse to occur. The influence of soil suction, gradual wetting, and the wetting and drying cycle on the collapsible behavior of the soil is also shown and discussed.

Roughness and surface material effects on nucleate boiling heat transfer from cylindrical surfaces to refrigerants R-134a and R-123

This paper presents results of an experimental investigation carried out to determine the effects of the surface roughness of different materials on nucleate boiling heat transfer of refrigerants R-134a and R-123. Experiments have been performed over cylindrical surfaces of copper, brass and stainless steel. Surfaces have been treated by different methods in order to obtain an average roughness, Ra, varying from 0.03 mu m to 10.5 mu m. Boiling curves at different reduced pressures have been raised as part of the investigation. The obtained results have shown significant effects of the surface material, with brass being the best performing and stainless steel the worst. Polished surfaces seem to present slightly better performance than the sand paper roughened. Boiling on very rough surfaces presents a peculiar behavior characterized by good thermal performance at low heat fluxes, the performance deteriorating at high heat fluxes with respect to smoother surfaces. (C) 2008 Elsevier Inc. All rights reserved.

Chemical composition of mixed construction and demolition recycled aggregates from the State of Sao Paulo

Construction and Demolition Waste (CDW) represents. about 50% of the total Brazilian municipal solid waste: thus, recycling represents huge benefits both in environmental and economic perspectives. Herein, the chemical characterization results of three samples from two different recycling plants from the State of Sao Paulo is prevented. The results demonstrated that the visual classification into grey and red is not related to the chemical composition but mostly to the grain size fraction. The chemical composition of the CDW varies according to the content of cement paste, natural aggregates (quartz sand or granite), red ceramic and clay. Furthermore, the production of recycled concrete aggregates requires two crushing stages to meet the technical standards. The sand fraction (below 4.8 mm) presents high grades of SiO(2), which indicates the liberation of cement paste to fines (< 0.15 mm). The fines have a great potential to be used in the cement industry.

Tempering temperature effects on abrasive wear of mottled cast iron

The effects of different tempering temperatures (300-600 degrees C) on abrasive wear resistance of mottled cast iron were studied. Abrasive wear tests were carried out using the rubber-wheel test on quartz sand and the pin test on Al(2)O(3) abrasive cloths. The retained austenite content of the matrix was determined by X-ray diffraction. The wear surface of the specimens was examined by scanning electron microscopy for identifying the wear micromechanism. Bulk hardness and matrix hardness before and after the tests were measured. The results showed that in the two-body (pin-on-disc test) system, the main wear mechanism was microcutting and high matrix hardening was presented. The wear rates presented higher correlation with the retained austenite than with the bulk and matrix hardness. In the three-body system (sand-rubber wheel), the wear surfaces presented indentations due to abrasive rolling. The wear rates had better correlation with both the bulk and matrix hardness (before and after the wear test) than with the retained austenite content. There are two groups of results, high and low wear rates corresponding to each tribosystem, two-body abrasive wear and three-body abrasive wear, respectively. (C) 2009 Elsevier B.V. All rights reserved.

On the classification of mixed construction and demolition waste aggregate by porosity and its impact on the mechanical performance of concrete

The properties of recycled aggregate produced from mixed (masonry and concrete) construction and demolition (C&D) waste are highly variable, and this restricts the use of such aggregate in structural concrete production. The development of classification techniques capable of reducing this variability is instrumental for quality control purposes and the production of high quality C&D aggregate. This paper investigates how the classification of C&D mixed coarse aggregate according to porosity influences the mechanical performance of concrete. Concretes using a variety of C&D aggregate porosity classes and different water/cement ratios were produced and the mechanical properties measured. For concretes produced with constant volume fractions of water, cement, natural sand and coarse aggregate from recycled mixed C&D waste, the compressive strength and Young modulus are direct exponential functions of the aggregate porosity. Sink and float technique is a simple laboratory density separation tool that facilitates the separation of cement particles with lower porosity, a difficult task when done only by visual sorting. For this experiment, separation using a 2.2 kg/dmA(3) suspension produced recycled aggregate (porosity less than 17%) which yielded good performance in concrete production. Industrial gravity separators may lead to the production of high quality recycled aggregate from mixed C&D waste for structural concrete applications.

Logística para agregados (brita e areia) em grandes centros urbanos

One of the human being`s basic needs is housing. In Brazil, the basic element for this is concrete, artificial stone, which demands a great amount of aggregates, such as sand and gravel. The sand and rocks are abundant in nature and gravel can be produced at low cost. However, transportation to the area of product utilization can be an incremental factor in the final cost logistics. Both sand and gravel have expressive price variations, which are not necessarily related to mining activities, but to logistic activities, mainly their distribution. Restrictive measures adopted in large urban centers, such as prohibition of hauling trucks in certain areas or during certain hours, alternate license plate end number system (even number plate ending can circulate on even-numbered days and visa versa), and axle-control, generate a need for a larger and more diversified fleet, not to mention more employees.

New Analytic Solution Related to the Richards, Philip, and Green-Ampt Equations for Infiltration

Based on physical laws of similarity, an analytic solution of the soil water potential form of the Richards equation was derived for water infiltration into a homogeneous sand. The derivation assumes a similarity between the soil water retention function and that of the soil water content profiles taken at fixed times. The new solution successfully described soil water content profiles experimentally measured for water infiltrating downward, upward, and horizontally into a homogeneous sand and agrees with that presented by Philip in 1957. The utility of this analysis is still to be verified, but it is expected to hold for soils that have a narrow pore-size distribution before wetting and that manifest a sharp increase of water content at the wetting front during infiltration. The effect of van Genuchten`s parameters alpha and n on the application of the solution to other porous media was investigated. The solution also improves and provides a more realistic description of the infiltration process than that pioneered by Green and Ampt in 1911.

Relation between incidence of Fusarium graminearum in seeds, emergence and occurrence of giberela in wheat seedlings

In order to verify the behavior of 30 genotypes of wheat in relation to the emergence and incidence of giberela in wheat seedlings from seeds contaminated with F graminearum, experiments were carried out under laboratory and greenhouse conditions. In the laboratory, seeds were analyzed for health using freezer blotter test. In the greenhouse, seeds were sowed in plastic boxes filled with sand treated with methyl bromide. Statistical design was randomized blocks with 30 treatments, four replications of 50 seeds (200 seeds/treatment). Emergence of seedlings and giberela incidence were evaluated at seven, 14 and 21 days after sowing. Symptomatic seedlings were removed and submitted to humid chambers for 24 hours under laboratory conditions. There was no significant difference in the incidence of the pathogen in the emergence of seedlings. There was no correlation between the incidence of F graminearum in the genotypes and incidence of giberela in seedlings, nor between the incidence of giberela in seedlings and the incidence of the pathogen in the seeds.

Use of growth regulators to overcome seed dormancy in Xylopia aromatica (Annonaceae)

Xylopia aromatica is a species of the Annonaceae family, native to the Brazilian ""Cerrado"". Seeds of this species usually possess morphophysiological dormancy which makes propagation more difficult. The objective of the present study was to evaluate the efficiency of removing the aril and sarcotesta and applying plant growth regulators to overcome dormancy in X. aromatica seeds. Seeds were separated into two groups: one consisting of seeds with aril and sarcotesta and another without these two seed coat appendices. Seeds with and without these appendices were soaked for 48 hours in distilled water or Promalin (R) (gibberellin 4 [GA(4)] + gibberellin 7 [GA(7)] and cytokinin [6-Benziladenine]) solutions of 250, 500 and 1,000 mg.L(-1), and sown in ""Cerrado"" soil. Later, seeds without the aril and sarcotesta were soaked for 48 hours in distilled water. Promalin (R) or GA(4) + GA(7) solutions at same concentrations and sown in sand or ""Cerrado"" soil. The removal of the aril and sarcotesta had a positive effect on the seed germination. Application of plant growth regulators helped to overcome dormancy in X. aromatica, with the greatest percentage of seedling emergence being observed in seeds treated with Promalin at 250 and 500 mg.L(-1) then sown in sand.

Characterization of humic substances in salt marsh soils under sea rush (Juncus maritimus)

Humic substances (HS) from salt marsh soils were characterized and the relationships among HS composition and some geochemical factors were analysed. For this, three salt marshes with the same vegetation cover (Juncus maritimus), but with different geochemical characteristics, were selected. The qualitative characterization of the soil humic acids and fulvic acids was carried out by elemental analysis, FTIR spectroscopy, fluorescence spectroscopy and VACP/MAS (13)C NMR spectroscopy. HS from salt marsh soils under sea rush (Juncus maritimus) displayed some shared characteristics such as low degree of humification, low aromatic content and high proportion of labile compounds, mainly polysaccharides and proteins. However, although the three salt marsh soils under study were covered by the same type of vegetation, the HS showed some important differences. HS composition was found to be determined not only by the nature of the original organic material, but also by environmental factors such as soil texture, redox conditions and tidal influence. In general. an increase in the humification process appeared to be related to aerobic conditions and predominance of sand in the mineral fraction of the soil, while the preservation of labile organic compounds may be associated with low redox potential values and fine soil texture. (C) 2008 Elsevier Ltd. All rights reserved.

Substratum choice for nesting in male Nile tilapia Oreochromis niloticus

Four substrata were offered to groups of adult Nile tilapia Oreochromis niloticus (one male and two females) simultaneously: pure sand, a mixture of sand and shells, stones and no substratum. The results showed that males chose to dig nests in a lighter and more homogeneous substratum.

Spatial patterns of soil attributes and components in a mangrove system in Southeast Brazil (Sao Paulo)

Purpose Among environmental factors governing innumerous processes that are active in estuarine environments, those of edaphic character have received special attention in recent studies. With the objectives of determining the spatial patterns of soil attributes and components across different mangrove forest landscapes and obtaining additional information on the cause-effect relationships between these variables and position within the estuary, we analyzed several soil attributes in 31 mangrove soil profiles from the state of So Paulo (Guaruja, Brazil). Materials and methods Soil samples were collected at low tide along two transects within the CrumahA(0) mangrove forest. Samples were analyzed to determine pH, Eh, salinity, and the percentages of sand, silt, clay, total organic carbon (TOC), and total S. Mineralogy of the clay fraction (< 2 mm) was also studied by X-ray diffraction analysis, and partitioning of solid-phase Fe was performed by sequential extraction. Results and discussion The results obtained indicate important differences in soil composition at different depths and landscape positions, causing variations in physicochemical parameters, clay mineralogy, TOC contents, and iron geochemistry. The results also indicate that physicochemical conditions may vary in terms of different local microtopographies. Soil salinity was determined by relative position in relation to flood tide and transition areas with highlands. The proportions of TOC and total S are conditioned by the sedimentation of organic matter derived from vegetation and by the prevailing redox conditions, which clearly favored intense sulfate reduction in the soils (similar to 80% of the total Fe is Fe-pyrite). Particle-size distribution is conditioned by erosive/deposition processes (present and past) and probably by the positioning of ancient and reworked sandy ridges. The existing physicochemical conditions appear to contribute to the synthesis (smectite) and transformation (kaolinite) of clay minerals. Conclusions The results demonstrate that the position of soils in the estuary greatly affects soil attributes. Differences occur even at small scales (meters), indicating that both edaphic (soil classification, soil mineralogy, and soil genesis) and environmental (contamination and carbon stock) studies should take such variability into account.

Infectivity of Strongyloides venezuelensis is influenced by variations in temperature and time of culture

The present research investigated the influence of temperature and time of larvae culture on the infectivity of Strongyloides venezuelensis. Mice were infected s.c. with 1500 larvae of S. venezuelensis maintained at 28 degrees C for three days of culture (dc), 28 degrees C for seven dc or 18 degrees C for seven dc. On days 1,3, 5, 7, 14 and 21 post-infection the animals were sacrificed and cell numbers in the blood, peritoneal cavity fluid (PCF), broncoalveolar fluid (BALF), cytokines, immunoglobulins, number of parasites and eggs/g of feces were quantified. Results demonstrated an increase in eosinophils and mononuclear cells in the blood, PCF and HALF of infected mice. Larvae at 28 degrees C/3dc induced earlier eosinophils in the PCF and HALF as opposed to larvae at 28 degrees C/7dc and 18 degrees C/7dc. Larvae at 28 degrees C/7dc induced higher synthesis of IL-4. IL-5 and IL-10 on days Sand 7 post-infection. Larvae at 28 degrees C/3dc in culture induced higher synthesis of IL-12 than larvae of seven dc, but time in culture induced better synthesis of IFN-gamma, after larval migration had ceased and only adult worms were present. Larvae at 28 degrees C/3dc in culture induced higher synthesis of IgG and IgG1 and expelled less female parasites than larvae cultivated for seven days. In conclusion, it was observed that the infectivity of S. venezuelensis is influenced by variations in temperature and time of culture. (C) 2010 Elsevier Inc. All rights reserved.