Test of a Modular Fault Current Limiter for 220 V Line Using YBCO Coated Conductor Tapes With Shunt Protection

A modular superconducting fault current limiter (SFCL) consisting of 16 elements was constructed and tested in a 220 V line for a fault current between 1 kA to 7.4 kA. The elements are made up of second generation (2G) YBCO-coated conductor tapes with stainless steel reinforcement. For each element four tapes were electrically connected in parallel with effective length of 0.4 m per element, totaling 16 elements connected in series. The evaluation of SFCL performance was carried out under DC and AC tests. The DC test was performed through pulsed current tests and its recovery characteristics under load current were analysed by changing the shunt resistor value. The AC test performed using a 3 MVA/220 V/60 Hz transformer has shown the current limiting ratio achieved a factor higher than 10 during fault of up to five cycles without conductor degradation. The measurement of the voltage for each element during the AC test showed that in this modular SFCL the quench is homogeneous and the transition occurs similarly in all the elements.

Electrical and Magnetic Characterization of BSCCO and YBCO HTS Tapes for Fault Current Limiter Application

Several high temperature superconductor (HTS) tapes have been developed since the late eighties. Due to the new techniques applied for their production, HTS tapes are becoming feasible and practical for many applications. In this work, we present the test results of five commercial HTS tapes from the BSCCO and YBCO families (short samples of 200 mm). We have measured and analyzed their intrinsic and extrinsic properties and compared their behaviors for fault current limiter (FCL) applications. Electrical measurements were performed to determine the critical current and the n value through the V-I relationship under DC and AC magnetic fields. The resistance per unit length was determined as a function of temperature. The magnetic characteristics were analyzed through susceptibility curves as a function of temperature. As transport current generates a magnetic field surrounding the HTS material, the magnetic measurements indicate the magnetic field supported by the tapes under a peak current 1.5 times higher than the critical current, I(c). By pulsed current tests the recovery time and the energy/volume during a current fault were also analyzed. These results are in agreement with the data found in the literature giving the most appropriate performance conductor for a FCL device (I(peak) = 4 kA) to be used in a 220 V-60 Hz grid.

Automatic tuning method for the design of supplementary damping controllers for flexible alternating current transmission system devices

The design of supplementary damping controllers to mitigate the effects of electromechanical oscillations in power systems is a highly complex and time-consuming process, which requires a significant amount of knowledge from the part of the designer. In this study, the authors propose an automatic technique that takes the burden of tuning the controller parameters away from the power engineer and places it on the computer. Unlike other approaches that do the same based on robust control theories or evolutionary computing techniques, our proposed procedure uses an optimisation algorithm that works over a formulation of the classical tuning problem in terms of bilinear matrix inequalities. Using this formulation, it is possible to apply linear matrix inequality solvers to find a solution to the tuning problem via an iterative process, with the advantage that these solvers are widely available and have well-known convergence properties. The proposed algorithm is applied to tune the parameters of supplementary controllers for thyristor controlled series capacitors placed in the New England/New York benchmark test system, aiming at the improvement of the damping factor of inter-area modes, under several different operating conditions. The results of the linear analysis are validated by non-linear simulation and demonstrate the effectiveness of the proposed procedure.

Data Mining Applied to Harmonic Current Sources Identification in Residential Consumers

This work proposes a method based on both preprocessing and data mining with the objective of identify harmonic current sources in residential consumers. In addition, this methodology can also be applied to identify linear and nonlinear loads. It should be emphasized that the entire database was obtained through laboratory essays, i.e., real data were acquired from residential loads. Thus, the residential system created in laboratory was fed by a configurable power source and in its output were placed the loads and the power quality analyzers (all measurements were stored in a microcomputer). So, the data were submitted to pre-processing, which was based on attribute selection techniques in order to minimize the complexity in identifying the loads. A newer database was generated maintaining only the attributes selected, thus, Artificial Neural Networks were trained to realized the identification of loads. In order to validate the methodology proposed, the loads were fed both under ideal conditions (without harmonics), but also by harmonic voltages within limits pre-established. These limits are in accordance with IEEE Std. 519-1992 and PRODIST (procedures to delivery energy employed by Brazilian`s utilities). The results obtained seek to validate the methodology proposed and furnish a method that can serve as alternative to conventional methods.

Ultrasound, eddy current and magnetic Barkhausen noise as tools for sigma phase detection on a UNS S31803 duplex stainless steel

Sigma phase is a deleterious one which can be formed in duplex stainless steels during heat treatment or welding. Aiming to accompany this transformation, ferrite and sigma percentage and hardness were measured on samples of a UNS S31803 duplex stainless steel submitted to heat treatment. These results were compared to measurements obtained from ultrasound and eddy current techniques, i.e., velocity and impedance, respectively. Additionally, backscattered signals produced by wave propagation were acquired during ultrasonic inspection as well as magnetic Barkhausen noise during magnetic inspection. Both signal types were processed via a combination of detrended-fluctuation analysis (DFA) and principal component analysis (PCA). The techniques used were proven to be sensitive to changes in samples related to sigma phase formation due to heat treatment. Furthermore, there is an advantage using these methods since they are nondestructive. (C) 2010 Elsevier B.V. All rights reserved.

Comparison between DC(+) and Square Wave AC SAW Current Outputs to Weld AISI 304 for Low-Temperature Applications

Welded equipment for cryogenic applications is utilized in chemical, petrochemical, and metallurgical industries. One material suitable for cryogenic application is austenitic stainless steel, which usually doesn`t present ductile/brittle transition temperature, except in the weld metal, where the presence of ferrite and micro inclusions can promote a brittle failure, either by ferrite cleavage or dimple nucleation and growth, respectively. A 25-mm- (1-in.-) thick AISI 304 stainless steel base metal was welded with the SAW process using a 308L solid wire and two kinds of fluxes and constant voltage power sources with two types of electrical outputs: direct current electrode positive and balanced square wave alternating current. The welded joints were analyzed by chemical composition, microstructure characterization, room temperature mechanical properties, and CVN impact test at -100 degrees C (-73 degrees F). Results showed that an increase of chromium and nickel content was observed in all weld beads compared to base metal. The chromium and nickel equivalents ratio for the weld beads were always higher for welding with square wave AC for the two types of fluxes than for direct current. The modification in the Cr(eq)/Ni(eq) ratio changes the delta ferrite morphology and, consequently, modifies the weld bead toughness at lower temperatures. The oxygen content can also affect the toughness in the weld bead. The highest absorbed energy in a CVN impact test was obtained for the welding condition with square wave AC electrical output and neutral flux, followed by DC(+) electrical output and neutral flux, and square wave AC electrical output and alloyed flux.

Flatness-based control of a single qubit gate

This work considers the open-loop control problem of steering a two-level quantum system from any initial to any final condition. The model of this system evolves on the state space X = SU(2), having two inputs that correspond to the complex amplitude of a resonant laser field. A symmetry preserving flat output is constructed using a fully geometric construction and quaternion computations. Simulation results of this flatness-based open-loop control are provided.

Persistent and remodeling hepatic preneoplastic lesions present differences in cell proliferation and apoptosis, as well as in p53, BcI-2 and NF-kappa B pathways

During rat hepatocarcinogenesis preneoplastic lesions (PNL) emerge which may persist (pPNL) and be sites of progress to cancer or suffer remodeling (rPNL) tending to disappear. Cellular and molecular mechanisms involved in both phenotypes are not sufficiently elucidated. pPNL and rPNL cellular proliferation and apoptosis were evaluated in rats submitted to the resistant hepatocyte (RH) model, and an adjusted growth index (AGI) was established. p53, Bcl-2, and NF-kappa B p65 subunit expression was evaluated by immunohistochemistry in pPNL and rPNL. p65 expression and NF-kappa B activation was evaluated by Western blot assays in whole livers. A lower number of BrdU-stained hepatocyte nuclei/mm(2) and higher number of apoptotic bodies (AB) per mm(2) were observed in remodeling compared to pPNL. Cytoplasmic p53 accumulation is related to increased hepatocarcinoma malignancy. We observed that 71.3% pPNL and 25.4% rPNL (P < 0.05) presented p53 staining in the cytoplasm. Similarly, 67.7% pPNL and 23.1 % rPNL (P < 0.05) presented increased Bcl-2 staining. Thirty-two percent pPNL and 15.6% rPNL (P < 0.05) presented p65 staining. Compared to normal rats, increase (P < 0.05) of hepatic p65 expression and NF-kappa B activation in rats submitted to the RH model was observed. in agreement to previous studies hepatic pPNL and rPNL differ regarding cell proliferation and apoptosis. Moreover, persistence and remodeling involve differences in p53, Bcl-2, and NF-kappa B pathways. These data point to molecular pathways that may direct preneoplastic lesions to spontaneously regress or to progress to cancer.

Electrochemical oxidation of acid black 210 dye on the boron-doped diamond electrode in the presence of phosphate ions: Effect of current density, pH, and chloride ions

The electrochemical oxidation of acid black 210 dye (AB-210) on the boron-doped diamond (BDD) was investigated under different pH conditions. The best performance for the AB-210 oxidation occurred in alkaline phosphate solution. This is probably due to oxidizing agents such as phosphate radicals and peroxodiphosphate ions, which can be electrochemically produced with good yields on the BDD anode, mainly in alkaline solution. Under this condition, the COD (chemical oxygen demand) removal was higher than that obtained from the model proposed by Comninellis. Electrolyses performed in phosphate buffer and in the presence of chloride ions resulted in faster COD and color removals in acid and neutral solutions, but in alkaline phosphate solution, a better performance in terms of TOC removal was obtained in the absence of chloride. Moreover, organochloride compounds were detected in all electrolyses performed in the presence of chloride. The AB-210 electrooxidation on BDD using phosphate as supporting electrolyte proved to be interesting since oxidizing species generated from phosphate ions were able to completely degrade the dye without producing organochloride compounds. (C) 2009 Elsevier Ltd. All rights reserved.

Symptoms after mould exposure including Stachybotrys chartarum, and comparison with darkroom disease

P>Background: Mould-attributed symptoms have included features which overlap with unexplained syndromes such as sick building syndrome. Objectives: We describe questionnaire and chart review findings in patients following exposure to moulds which include Stachybotrys and compare responses with two control groups. Methods: Thirty-two patients presented with symptoms attributed to mould exposures. Exposure identification for 25 patients had reported S tachybotrys chartarum as well as other mould (Aspergillus, Penicillium), 88% at work. The remaining seven had professionally visualized or self-reported/photographic exposure evidence only. A chart review was performed and a follow-up with a questionnaire, including questions on current health status, and nonspecific symptoms. Results: Cough, shortness of breath and chest tightness (at presentation) were reported in 79%, 70% and 64%, respectively, and persisted > 6 weeks in 91%. Skin test(s) were positive to fungal extract(s) in 30%. Seventeen returned questionnaires were obtained 3.1 (SD 0.5) years after the initial clinic assessment. Among this subgroup, persisting asthma-like symptoms and symptoms suggestive of sick building syndrome were frequent, and similar to a group previously assessed for darkroom disease among medical radiation technologists. The mould-exposed group more commonly reported they were bothered when walking in a room with carpets, complained of a chemical or metallic taste in their mouth, and had problems in concentration when compared with a control physiotherapist group (P < 0.005). Conclusions: Although only a minority with health concerns from indoor mould exposure had demonstrable mould-allergy, a significant proportion had asthma-like symptoms. Other symptoms were also common and persistent after the initial implicated exposure.

Hormone profile in juvenile systemic lupus erythematosus with previous or current amenorrhea

To identify the underlying mechanism of amenorrhea in juvenile systemic lupus erythematosus (JSLE) patients, thirty-five (11.7%) JSLE patients with current or previous amenorrhea were consecutively selected among the 298 post-menarche patients followed in 12 Brazilian pediatric rheumatology centers. Pituitary gonadotrophins [follicle-stimulating hormone (FSH) and luteinizing hormone (LH)] and estradiol were evaluated in 32/35 patients, and prolactin and total testosterone in 29/35 patients. Patient`s medical records were carefully reviewed according to demographic, clinical and therapeutic findings. The mean duration of amenorrhea was 7.2 +/- A 3.6 months. Low FSH or LH was observed in 7/32 (22%) JSLE patients and normal FSH or LH in 25 (78%). Remarkably, low levels of FSH or LH were associated with higher frequency of current amenorrhea (57% vs. 0%, P = 0.001), higher median disease activity (SLEDAI) and damage (SLICC/ACR-DI) (18 vs. 4, P = 0.011; 2 vs. 0, P = 0.037, respectively) and higher median current dose of prednisone (60 vs. 10 mg/day, P = 0.0001) compared to normal FSH or LH JSLE patients. None of them had decreased ovarian reserve and premature ovarian failure. Six of 29 (21%) patients had high levels of prolactin, and none had current amenorrhea. No correlations were observed between levels of prolactin and SLEDAI, and levels of prolactin and SLICC/ACR-DI scores (Spearman`s coefficient). We have identified that amenorrhea in JSLE is associated with high dose of corticosteroids indicated for active disease due to hypothalamic-pituitary-ovary axis suppression.

Sertraline vs. ELectrical Current Therapy for Treating Depression Clinical Trial - SELECT TDCS: Design, rationale and objectives

Background: Despite significant advancements in psychopharmacology, treating major depressive disorder (MDD) is still a challenge considering the efficacy, tolerability, safety, and economical costs of most antidepressant drugs. One approach that has been increasingly investigated is modulation of cortical activity with tools of non-invasive brain stimulation - such as transcranial magnetic stimulation and transcranial direct current stimulation (tDCS). Due to its profile, tDCS seems to be a safe and affordable approach. Methods and design: The SELECT TDCS trial aims to compare sertraline vs. tDCS in a double-blinded, randomized, factorial trial enrolling 120 participants to be allocated to four groups to receive sertraline + tDCS, sertraline, tDCS or placebo. Eligibility criteria are moderate-to-severe unipolar depression (Hamilton Depression Rating Scale >17) not currently on sertraline treatment. Treatment will last 6 weeks and the primary outcome is depression change in the Montgomery-Asberg Depression Rating Score (MADRS). Potential biological markers that mediate response, such as BDNF serum levels, Val66Met BDNF polymorphism, and heart rate variability will also be examined. A neuropsychological battery with a focus on executive functioning will be administered. Discussion: With this design we will be able to investigate whether tDCS is more effective than placebo in a sample of patients free of antidepressants and in addition, we will be able to secondarily compare the effect sizes of sertraline vs. tDCS and also the comparison between tDCS and combination of tDCS and sertraline. (C) 2010 Elsevier Inc. All rights reserved.

AIDS in Latin America: assessing the current status of the epidemic and the ongoing response

Background This article provides a summary of the current status of the HIV/AIDS epidemic in Latin America, as well as an outline of the diverse responses to it. Methods A search of international databases (Pubmed and ISI-Web of Science), regional databases (Scielo and Lilacs), regional and national documents and UNAIDS reports. Data are presented according to subregion. Results In Mexico HIV remains concentrated among urban men who have sex with men (MSM), and has been growing among injecting drug users (IDU) and in rural areas in relation to migration. An increasing proportion of women among those affected is observed in all countries in Central America, the most affected region, as well as increasing the impact on other vulnerable groups, such as indigenous populations. The Andean Countries have urban epidemics concentrated among MSM. In Peru, non-traditional vulnerable populations were identified. In the Southern Cone heterosexual transmission became more relevant, probably in connection with IDU epidemics and is increasingly affecting lower income groups. Incidence rates have been declining since 2002 in Brazil, the first country to guarantee free, universal access to antiretrovirals, where one-third of drug-nave patients are still initiating treatment at an advanced stage. Generally, access to treatment has improved as a result of support from the Global Fund and other initiatives, but there are concerns regarding coverage, equity and sustainability. Conclusions HIV is still concentrated among MSM in Latin America. Non-traditional vulnerable groups such as migrants and lower income populations, usually considered part of the general population, deserve attention. Programmes confronting sexual exclusion are still needed. Access to treatment has improved over time, but inequalities persist.

Health in Brazil 4 Chronic non-communicable diseases in Brazil: burden and current challenges

Non-communicable diseases (NCDs) have become a major health priority in Brazil-72% of all deaths were attributable to NCDs in 2007. They are also the main source of disease burden, with neuropsychiatric disorders being the single largest contributor. Morbidity and mortality due to NCDs are greatest in the poor population. Although the crude NCD mortality increased 5% between 1996 and 2007, age-standardised mortality declined by 20%. Declines were primarily for cardiovascular and chronic respiratory diseases, in association with the successful implementation of health policies that lead to decreases in smoking and the expansion of access to primary health care. Of note, however, the prevalence of diabetes and hypertension is rising in parallel with that of excess weight; these increases are associated with unfavourable changes of diet and physical activity. Brazil has implemented major policies for the prevention of NCDs, and its age-adjusted NCD mortality is falling by 1.8% per year. However, the unfavourable trends for most major risk factors pose an enormous challenge and call for additional and timely action and policies, especially those of a legislative and regulatory nature and those providing cost-effective chronic care for individuals affected by NCDs.