Effect of therapeutic dose X rays on mechanical and chemical properties of esthetic dental materials

The aim of this study was to investigate the influence of therapeutic dose X rays on the microhardness (MH) and degree of conversion (DC) of two different esthetic restorative dental materials. The materials were photo-activated with a LED light-curing unit using three cure-times: 5, 20 and 40 seconds. The photo-activation was carried out in two distinct periods: before and after irradiation with doses of 5, 35 and 70 Gy, from a 6 MV X rays beam. In accordance with the methodology used, it was conclude that a therapeutic dose does not have a detrimental effect on the photoinitiator molecules, because the photo-activation occurred after they were irradiated. When the irradiation was applied before photo-activation, the materials showed MH improvement, but when photo-activation was performed after irradiation, there was less improvement. However, there was no correlation between MH and DC. Thus, a therapeutic dose applied to cured material can promote linking and breaking of chain bonds in a non-linear way.

Visual contrast sensitivity in tonic-clonic epileptic patients

We measured the effects of epilepsy on visual contrast sensitivity to linear and vertical sine-wave gratings. Sixteen female adults, aged 21 to 50 years, comprised the sample in this study, including eight adults with generalized tonic-clonic seizure-type epilepsy and eight age-matched controls without epilepsy. Contrast threshold was measured using a temporal two-alternative forced-choice binocular psychophysical method at a distance of 150 cm from the stimuli, with a mean luminance of 40.1 cd/m². A one-way analysis of variance (ANOVA) applied to the linear contrast threshold showed significant differences between groups (F[3,188] = 14.829; p < .05). Adults with epilepsy had higher contrast thresholds (1.45, 1.04, and 1.18 times for frequencies of 0.25, 2.0, and 8.0 cycles per degree of visual angle, respectively). The Tukey Honestly Significant Difference post hoc test showed significant differences (p < .05) for all of the tested spatial frequencies. The largest difference between groups was in the lowest spatial frequency. Therefore, epilepsy may cause more damage to the neural pathways that process low spatial frequencies. However, epilepsy probably alters both the magnocellular visual pathway, which processes low spatial frequencies, and the parvocellular visual pathway, which processes high spatial frequencies. The experimental group had lower visual contrast sensitivity to all tested spatial frequencies.

Nanochromics: old materials, new structures and architectures for high performance devices

Due to the development of nanoscience, the interest in electrochromism has increased and new assemblies of electrochromic materials at nanoscale leading to higher efficiencies and chromatic contrasts, low switching times and the possibility of color tuning have been developed. These advantages are reached due to the extensive surface area found in nanomaterials and the large amount of organic electrochromic molecules that can be easily attached onto inorganic nanoparticles, as TiO2 or SiO2. Moreover, the direct contact between electrolyte and nanomaterials produces high ionic transfer rates, leading to fast charge compensation, which is essential for high performance electrochromic electrodes. Recently, the layer-by-layer technique was presented as an interesting way to produce different architectures by the combination of both electrochromic nanoparticles and polymers. The present paper shows some of the newest insights into nanochromic science.

As aves da Estação Ecológica Serra Geral do Tocantins, Centro do Brasil

A Estação Ecológica Serra Geral do Tocantins (EESGT) é uma das maiores Unidades de Conservação dentro do Bioma Cerrado. A avifauna desta UC foi inventariada entre os dias 25 de janeiro e 15 de fevereiro de 2008. Durante esse trabalho buscou-se amostrar os diferentes hábitats encontrados na EESGT, bem como algumas localidades no entorno. Além de registros auditivos e visuais foram utilizadas redes-de-neblina e armas de fogo para coletas de material testemunho, que se encontra depositado na coleção ornitológica do Museu de Zoologia da Universidade de São Paulo (MZUSP). Os resultados obtidos foram comparados com os dados disponíveis para outras unidades de conservação presentes na região. Foram registradas 254 espécies de aves, incluindo 11 endêmicas do Cerrado e outras três ameaçadas de extinção (Taoniscus nanus, Anodorhynchus hyacinthinus e Procnias averano). Três indivíduos pertencentes ao gênero Picumnus foram coletados; estes apresentam um distinto padrão de plumagem e de vocalização, podendo representar um táxon ainda não descrito.

Percepções de escolares com deficiência visual em relação ao seu processo de escolarização

A promoção da inclusão escolar de pessoas com deficiência visual demanda que os profissionais conheçam as percepções que estes alunos têm a respeito de suas limitações e possibilidades. Neste estudo, foram identificadas características e percepções de escolares com deficiência visual em relação ao seu processo de reabilitação. Foi realizado um estudo descritivo transversal com escolares de 12 anos e mais, inseridos no sistema público de um município do Estado de São Paulo. Aplicou-se questionário mediante entrevista. Obteve-se população de 26 alunos, sendo 46,2% com visão subnormal e 53,8% com cegueira, com média de idade de 17,1 anos. A repetência escolar foi declarada por 73,1%. Entre as dificuldades escolares decorrentes da cegueira, sobressaiu-se a leitura de livros didáticos e, entre as decorrentes da visão subnormal, a visualização da lousa. O nível de escolaridade mostrou-se baixo em relação à média de idade. Evidenciaram-se percepções coerentes em relação à problemática da inclusão escolar.

Fatores relacionados à autopercepção da audição entre idosos do município de São Paulo - Projeto SABE

Este artigo relata a influência de fatores sociodemográficos e de saúde na autopercepção da audição entre os idosos do projeto " Saúde, Bem-Estar e Envelhecimento" (Projeto SABE) no município de São Paulo. O estudo incluiu 2.143 indivíduos de 60 anos e mais. Um modelo de regressão logística ordinal, considerando o desenho da amostra, foi usado na análise multivariável. O aumento da idade; o sexo masculino; morar acompanhado; relatar tontura; memória regular/ ruim e saúde regular ou ruim aumentaram a chance de autopercepção ruim da audição. O conhecimento da autopercepção da audição e dos seus fatores relacionados é importante para avaliar a qualidade de vida dos idosos e a necessidade de reabilitação auditiva

Mães de crianças com deficiência visual: percepções, conduta e constribuição do atendimento em grupo

A presente pesquisa teve quatro objetivos: 1) identificar reações de mães em relação ao diagnóstico da deficiência visual; 2) identificar o responsável pela detecção da deficiência; 3) verificar dificuldades da criança no processo de escolarização, e 4) verificar possíveis contribuições de atividades terapêuticas direcionadas ao grupo de mães. Foi realizado um "survey" descritivo com as mães de crianças com deficiência visual, atendidas no CEPRE-FCM-Unicamp. Para a coleta de dados foi utilizado um questionário aplicado por entrevista, desenvolvido após estudo exploratório. Compôs-se uma amostra não probabilística, constituída por 14 mães. Entre os resultados obtidos, com relação aos sentimentos apontados pelas mães em relação ao diagnóstico, destacaram-se: a tristeza (71,0 por cento); o medo (64,0 por cento) e a decepção (42,0 por cento). O problema visual foi percebido por mães em 53,0 por cento dos casos, por pediatras em 26,0 por cento e por familiares em 21,0 por cento. Entre as dificuldades da criança no processo de escolarização foram apontadas: medo de não conseguirem acompanhar as exigências escolares (75,0 por cento) e discriminação (63,0 por cento). A maioria das mães (78,0 por cento) acredita que as atividades do grupo contribuem para o esclarecimento de dúvidas, e as atividades terapêuticas contribuíram para que aprendessem a lidar com as dificuldades de seus filhos (78,0 por cento). Os resultados obtidos contribuíram para concluir: que os sentimentos de tristeza, medo e decepção mostraram-se mais evidentes; que, na maioria dos casos, a deficiência visual foi detectada pela mãe; que na opinião das mães, as crianças teriam dificuldades em acompanhar as atividades escolares e que o grupo contribuiu para esclarecer dúvidas e favorecer troca de experiências

Visual Feedforward Control in Human Locomotion During Avoidance of Obstacles that Change Size

The purpose of the current study was to understand how visual information about an ongoing change in obstacle size is used during obstacle avoidance for both lead and trail limbs. Participants were required to walk in a dark room and to step over an obstacle edged with a special tape visible in the dark. The obstacle's dimensions were manipulated one step before obstacle clearance by increasing or decreasing its size. Two increasing and two decreasing obstacle conditions were combined with seven control static conditions. Results showed that information about the obstacle's size was acquired and used to modulate trail limb trajectory, but had no effect on lead limb trajectory. The adaptive step was influenced by the time available to acquire and process visual information. In conclusion, visual information about obstacle size acquired during lead limb crossing was used in a feedforward manner to modulate trail limb trajectory.

Evaluation technique for determining wheel performance in the grinding of aerospace materials

Nickel-based super alloys are used in a variety of applications in which high-temperature strength and resistance to creep, corrosion, and oxidation are required, such as in aircraft gas turbines, combustion chambers, and automotive engine valves. The properties that make these materials suitable for these applications also make them difficult to grind. Grinding systems for such materials are often built around vitrified cBN (cubic boron nitride) wheels to realize maximum productivity and minimum cost per part. Conditions that yield the most economical combination of stock removal rate and wheel wear are key to the successful implementation of the grinding system. Identifying the transition point for excessive wheel wear is important. The aim of this study is to compare the performance of different cBN wheels when grinding difficult-to-grind (DTG) materials by determining the 'wheel wear characteristic curve', which correlates the G-ratio to the calculated tangential force per abrasive grain. With the proposed methodology, a threshold force per grit above which the wheel wear rate increases rapidly can be quickly identified. A comparison of performance for two abrasive product formulations in the grinding of three materials is presented. The obtained results can be applied for the development of grinding applications for DTG materials.

Analysis of the tip roundness effects on the micro- and macroindentation response of elastic-plastic materials

In this work, the effects of indenter tip roundness oil the load-depth indentation curves were analyzed using finite element modeling. The tip roundness level was Studied based on the ratio between tip radius and maximum penetration depth (R/h(max)), which varied from 0.02 to 1. The proportional Curvature constant (C), the exponent of depth during loading (alpha), the initial unloading slope (S), the correction factor (beta), the level of piling-up or sinking-in (h(c)/h(max)), and the ratio h(max)/h(f) are shown to be strongly influenced by the ratio R/h(max). The hardness (H) was found to be independent of R/h(max) in the range studied. The Oliver and Pharr method was successful in following the variation of h(c)/h(max) with the ratio R/h(max) through the variation of S with the ratio R/h(max). However, this work confirmed the differences between the hardness values calculated using the Oliver-Pharr method and those obtained directly from finite element calculations; differences which derive from the error in area calculation that Occurs when given combinations of indented material properties are present. The ratio of plastic work to total work (W(p)/W(t)) was found to be independent of the ratio R/h(max), which demonstrates that the methods for the Calculation of mechanical properties based on the *indentation energy are potentially not Susceptible to errors caused by tip roundness.

Analysis of the effects of conical indentation variables on the indentation response of elastic-plastic materials through factorial design of experiment

In this work, the effects of conical indentation variables on the load-depth indentation curves were analyzed using finite element modeling and dimensional analysis. A factorial design 2(6) was used with the aim of quantifying the effects of the mechanical properties of the indented material and of the indenter geometry. Analysis was based on the input variables Y/E, R/h(max), n, theta, E, and h(max). The dimensional variables E and h(max) were used such that each value of dimensionless Y/E was obtained with two different values of E and each value of dimensionless R/h(max) was obtained with two different h(max) values. A set of dimensionless functions was defined to analyze the effect of the input variables: Pi(1) = P(1)/Eh(2), Pi(2) = h(c)/h, Pi(3) = H/Y, Pi(4) = S/Eh(max), Pi(6) = h(max)/h(f) and Pi(7) = W(P)/W(T). These six functions were found to depend only on the dimensionless variables studied (Y/E, R/h(max), n, theta). Another dimension less function, Pi(5) = beta, was not well defined for most of the dimensionless variables and the only variable that provided a significant effect on beta was theta. However, beta showed a strong dependence on the fraction of the data selected to fit the unloading curve, which means that beta is especially Susceptible to the error in the Calculation of the initial unloading slope.

Using the ultrasound and instrumented indentation techniques to measure the elastic modulus of engineering materials

Currently, the acoustic and nanoindentation techniques are two of the most used techniques for material elastic modulus measurement. In this article fundamental principles and limitations of both techniques are shown and discussed. Last advances in nanoindentation technique are also reviewed. An experimental study in ceramic, metallic, composite and single crystals was also done. Results shown that ultrasonic technique is capable to provide results in agreement with those reported in literature. However, ultrasonic technique does not allow measuring the elastic modulus of some small samples and single crystals. On the other hand, the nanoindentation technique estimates the elastic modulus values in reasonable agreement with those measured by acoustic methods, particularly in amorphous materials, while in some policristaline materials some deviation from expected values was obtained.

Ferromagnetic resonance for the quantification of superparamagnetic iron oxide nanoparticles in biological materials

The aim of the present work is the presentation of a quantification methodology for the control of the amount of superparamagnetic iron oxide nanoparticles (SPIONs) administered in biological materials by means of the ferromagnetic resonance technique (FMR) applied to studies both in vivo and in vitro. The in vivo study consisted in the analysis of the elimination and biodistribution kinetics of SPIONs after intravenous administration in Wistar rats. The results were corroborated by X-ray fluorescence. For the in vitro study, a quantitative analysis of the concentration of SPIONs bound to the specific AC133 monoclonal antibodies was carried out in order to detect the expression of the antigenic epitopes (CD133) in stem cells from human umbilical cord blood. In both studies FMR has proven to be an efficient technique for the SPIONs quantification per volume unit (in vivo) or per labeled cell (in vitro).

Cavity Preparation and Influence of Restorative Materials on the Prevention of Secondary Caries

Objective: This in vitro study evaluated the influence of cavity preparation using the Er:YAG laser and restorative materials containing fluoride on preventing caries lesions. Background: It has been suggested that cavity preparation using the Er:YAG laser has a potential for improving resistance to secondary caries on enamel. Methods: Forty unerupted human third molars teeth were sectioned into 72 blocks of dental enamel and distributed into two groups to prepare cavities measuring (1.6 mm diameter) with diamond burs (DB) or Er:YAG laser (LA; 6 Hz, 300 mJ, 47 J/cm(2)). After that, each group was divided into three subgroups and restored with a glass-ionomer cement (GI), a resin-modified glass-ionomer (RM), or a composite resin (CR). Blocks were thermal cycled and submitted to a pH challenge to develop artificial caries-like lesions. Lesions were evaluated by Knoop microhardness test. An average of four indentations was used. Statistical analyses were performed by ANOVA followed by Tukey's test. Results: The results (in Knoop hardness number) for DB cavity preparation were GI, 235.5 (+/- 75.5); RM, 137.1 (+/- 64.1); and CR, 39.3 (+/- 26.5). For LA cavity preparation, the results were GI, 410.0 (+/- 129.7); RM, 310.3 (+/- 119.5); and CR, 96.4 (+/- 57.4). Conclusions: There was less development of caries lesion around LA-prepared cavities than around the DB-prepared cavities; however, no synergistic cariostatic effect was observed between the Er:YAG laser and glass ionomer cement.

LED Phototherapy to Prevent Mucositis: A Case Report

Objective: The purpose of this case report was to evaluate the efficacy of phototherapy using light-emitting diodes (LEDs) to prevent oral mucositis in a Hodgkin's disease patient treated with the ABVD ( doxorubicin [Adriamycin], bleomycin, vinblastine, and dacarbazine) chemotherapy regimen. Background Data: Mucositis is a common dose-limiting complication of cancer treatment, and if severe it can lead to alterations in treatment planning or suspension of cancer therapy, with serious consequences for tumor response and survival. Therefore, low-power lasers and more recently LEDs, have been used for oral mucositis prevention and management, with good results. Materials and Methods: In this study, a 34-year-old man received intraoral irradiation with an infrared LED array (880 nm, 3.6 J/cm(2), 74 mW) for five consecutive days, starting on chemotherapy day 1. In each chemotherapy cycle, he received the ABVD protocol on days 1 and 15, and received LED treatment for 5 d during each cycle. To analyze the results, the World Health Organization (WHO) scale was used to grade his mucositis, and a visual analogue scale (VAS) was used for pain evaluation, on days 1, 3, 7, 10, and 13 post-chemotherapy. Results: The results showed that the patient did not develop oral mucositis during the five chemotherapy cycles, and he had no pain symptoms. Conclusion: LED therapy was a safe and effective method for preventing oral mucositis in this case report. However, further randomized studies with more patients are needed to prove the efficacy of this method.