Durability and compressive strength of blast furnace slag-based cement grout for special geotechnical applications

Special foundations, most prominently micropiles and soil anchors, are frequently used in construction today. In Spain, the grout for these special technical applications is generally prepared with portland cement, although the codes and standards in place stipulate only the minimum compressive strength required, with no mention of cement type. Those texts also establish a range of acceptable water:cement ratios. In the present study, durability and compressive strength in cement grout prepared with blast furnace slag cement at different w/c ratios are characterised and compared to the findings for a reference portland cement grout. The results show that slag grout exhibits greater durability than the portland cement material and complies with the compressive strength requirements laid down in the respective codes.

Mechanical Properties and Durability of CNT Cement Composites

In the present paper, changes in mechanical properties of Portland cement-based mortars due to the addition of carbon nanotubes (CNT) and corrosion of embedded steel rebars in CNT cement pastes are reported. Bending strength, compression strength, porosity and density of mortars were determined and related to the CNT dosages. CNT cement paste specimens were exposed to carbonation and chloride attacks, and results on steel corrosion rate tests were related to CNT dosages. The increase in CNT content implies no significant variations of mechanical properties but higher steel corrosion intensities were observed.

Influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles

Today, the use of micropiles for different applications has become very common. In Spain, the cement grouts for micropiles are prepared using ordinary Portland cement and w:c ratio 0.5, although the micropiles standards do not restrict the cement type to use, provided that it reaches a certain compressive strength. In this study, the influence of using slag cement on the microstructure and durability related properties of cement grouts for micropiles have been studied until 90 hardening days, compared to an ordinary Portland cement. Finally, slag cement grouts showed good service properties, better than ordinary Portland cement ones.

The influence of rock fabric in the durability of two sandstones used in the Andalusian Architectural Heritage (Montoro and Ronda, Spain)

Natural stone has been a popular and reliable building material throughout history appearing in many historic monuments and in more recent buildings. Research into the intrinsic properties of specific stones is important because it gives us a greater understanding of the factors that limit and act on them. This can help prevent serious problems from occurring in our buildings bringing both esthetic benefits and financial savings. To this end, the main objective of this research has been to study the influence of the fabric and the mineral composition of two types of sandstone on their durability. The first is a red continental sandstone from the Buntsandstein Age called “Molinaza Roja”, which is quarried in Montoro (Cordoba). The second is quarried in Ronda (Malaga) and is sold under the trade name of “Arenisca Ronda”. It is a light pink-whitish calcarenite deposited during the Late Tortonian to Late Messinian. We characterized their petrological and petrophysical properties by studying their rock fabrics, porous systems and mechanical properties. In order to obtain a complete vision of the behavior of their rock fabrics, we also carried out two decay tests, the salt crystallization and the freeze–thaw tests. We then measured the effects on the textures of the altered samples during and after the decay tests and we evaluated the changes in the porous system. By comparing the results between intact and altered samples, we found that Arenisca Ronda is less durable because it has a high quantity of expandable clays (smectites) and a high percentage of pores in the 0.1–1 μm range, in which the pressure produced by salt crystallization is strongest. In Molinaza Roja the decay agents caused significant sanding due to loss of cohesion between the clasts, especially during the salt crystallization test. In both stones, the anisotropies (oriented textures) have an important role in their hydric and dynamic behavior and also affect their mechanical properties (especially in the compression resistance). No changes in color were detected.

Estudio de propiedades físicas de las rocas

El objetivo de este taller es mostrar a los alumnos mediante experiencias de laboratorio sencillas y de bajo coste algunas metodologías de estudio de las propiedades físicas de las rocas como material de construcción. Las propiedades físicas de las rocas determinan su uso y comportamiento tanto como materiales de construcción como soportes de obra civil. La determinación de las propiedades físicas complementan el estudio mineralógico y textural (petrográfico) de los materiales pétreos y naturales. Las propiedades petrofísicas más importantes que se abordan en este taller son el sistema poroso (porosidad); transporte de fluidos (permeabilidad, capilaridad); propiedades mecánicas (estáticas y dinámicas); la durabilidad de las rocas frente a las sales, hielo, ataque ácido, etc.

Washcoated Pd/Al2O3 monoliths for the liquid phase hydrodechlorination of dioxins

The catalytic activity and durability of 2 wt.% Pd/Al2O3 in powder and washcoated on cordierite monoliths were examined for the liquid phase hydrodechlorination (LPHDC) of polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/Fs), also known as dioxins. NaOH was employed as a neutralizing agent, and 2-propanol was used as a hydrogen donor and a solvent. Fresh and spent powder and monolith samples were characterized by elemental analysis, surface area, hydrogen chemisorption, scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX), and transmission electron microscopy/energy dispersive X-ray spectroscopy (TEM/EDX). Three reactor configurations were compared including the slurry and monolith batch reactors as well as the bubble loop column resulting in 100, 70, and 72% sample toxicity reduction, respectively, after 5 h of reaction. However, the slurry and monolith batch reactors lead to catalyst sample loss via a filtration process (slurry) and washcoat erosion (monolith batch), as well as rapid deactivation of the powder catalyst samples. The monolith employed in the bubble loop column remained stable and active after four reaction runs. Three preemptive regeneration methods were evaluated on spent monolith catalyst including 2-propanol washing, oxidation/reduction, and reduction. All three procedures reactivated the spent catalyst samples, but the combustion methods proved to be more efficient at eliminating the more stable poisons.

Self-sensing properties of alkali activated blast furnace slag (BFS) composites reinforced with carbon fibers

In recent years, several researchers have shown the good performance of alkali activated slag cement and concretes. Besides their good mechanical properties and durability, this type of cement is a good alternative to Portland cements if sustainability is considered. Moreover, multifunctional cement composites have been developed in the last decades for their functional applications (self-sensing, EMI shielding, self-heating, etc.). In this study, the strain and damage sensing possible application of carbon fiber reinforced alkali activated slag pastes has been evaluated. Cement pastes with 0, 0.29 and 0.58 vol % carbon fiber addition were prepared. Both carbon fiber dosages showed sensing properties. For strain sensing, function gage factors of up to 661 were calculated for compressive cycles. Furthermore, all composites with carbon fibers suffered a sudden increase in their resistivity when internal damages began, prior to any external signal of damage. Hence, this material may be suitable as strain or damage sensor.

Efecto de la adición de nanofibras de carbono en las propiedades mecánicas y de durabilidad de materiales cementantes

En este artículo se han estudiado los cambios en las propiedades mecánicas de los morteros de cemento Portland debido a la adición de nanofibras de carbono (NFC). Se han determinado las resistencias a flexotracción y a compresión de los morteros en relación a la cantidad de NFC añadidas a la mezcla, al tiempo de curado y a la porosidad y densidad de los mismos. Además se han investigado los niveles de corrosión de barras de acero embebidas en pastas de cemento con NFC expuestos al ataque por carbonatación y por ingreso de cloruros. El aumento en el porcentaje de NFC añadido se traduce en un aumento la intensidad de corrosión registrada y una mejora de las propiedades mecánicas.

Influencia de diferentes condiciones de curado en la estructura porosa y en las propiedades a edades tempranas de morteros que contienen ceniza volante y escoria de alto horno

En este trabajo se ha estudiado la evolución de la microestructura, propiedades de durabilidad y resistencias mecánicas de morteros preparados con cementos comerciales, que contienen ceniza volante (entre un 21% y un 35%) y escoria de alto horno (entre un 66% y un 80%), expuestos a tres ambientes, un ambiente óptimo de laboratorio, y dos ambientes representativos del clima Atlántico y Mediterráneo respectivamente. Como referencia de comportamiento, también se ensayaron morteros de cemento Portland. La microestructura se caracterizó mediante porosimetría de intrusión de mercurio. En lo referente a la durabilidad, se estudiaron los coeficientes de absorción capilar y de migración de cloruros en estado no estacionario. También se determinó la resistencia a compresión de los morteros. Los ensayos se realizaron a 7, 28 y 90 días. La principal conclusión alcanzada es que los cementos con cenizas y escorias expuestos a condiciones ambientales representativas de los climas Atlántico y Mediterráneo, pueden desarrollar unas propiedades en servicio adecuadas al cabo de tres meses.

Temperature influence on the physical and mechanical properties of a porous rock: San Julian's calcarenite

This work discusses the results from tests which were performed in order to study the effect of high temperatures in the physical and mechanical properties of a calcarenite (San Julian's stone). Samples, previously heated at different temperatures (from 105 °C to 600 °C), were tested. Non-destructive tests (porosity and ultrasonic wave propagation) and destructive tests (uniaxial compressive strength and slake durability test) were performed over available samples. Furthermore, the tests were carried out under different conditions (i.e. air-cooled and water-cooled) in order to study the effect of the fire off method. The results show that uniaxial compressive strength and elastic parameters (i.e. elastic modulus and Poisson's ratio), decrease as the temperature increases for the tested range of temperatures. A reduction of the uniaxial compressive strength up to 35% and 50% is observed in air-cooled and water-cooled samples respectively when the samples are heated to 600 °C. Regarding the Young's modulus, a fall over 75% and 78% in air-cooled and water-cooled samples respectively is observed. Poisson's ratio also declines up to 44% and 68% with the temperature in air-cooled and water-cooled samples respectively. Slake durability index also exhibits a reduction with temperature. Other physical properties, closely related with the mechanical properties of the stone, are porosity, attenuation and propagation velocity of ultrasonic waves in the material. All exhibit considerable changes with temperature.

Propiedades físicas y mecánicas de una calcarenita: la Piedra de San Julián

En este trabajo se estudian las características físico-mecánicas de la Piedra de San Julián y su comportamiento frente a procesos de calentamiento a temperaturas similares a las alcanzadas en un incendio, así como la puesta a punto y validación de métodos dinámicos no destructivos para el dictamen del estado de desgaste del material. El enfoque está orientado a los parámetros que más interesan en la utilización de la Piedra como material de construcción. Dado que esta Tesis se realiza por compendio de artículos, por razones prácticas y necesidades de publicación, el contenido de la misma está dividido en tres grandes bloques, como son: fluencia, exposición a altas temperaturas y relación entre módulos estáticos y dinámicos. Para el estudio de la fluencia o deformabilidad a largo plazo bajo carga constante se han realizado ensayos de carga estáticos de larga duración. Por otra parte, se ha efectuado un análisis del comportamiento reológico del hormigón en las distintas normativas, especialmente en el Código Modelo FIB (2010), y se ha buscado un paralelismo entre las previsiones del Código y los resultados obtenidos en los ensayos. Al mismo tiempo se han probado varios modelos reológicos que reproduzcan de forma precisa el comportamiento de la fluencia según el Código y los ensayos. Esto ha permitido ajustar una función, adaptando las especificaciones del Código modelo, que describe la deformación en el tiempo de la Piedra de San Julián. La validez teórica de esta ecuación alcanza períodos temporales similares a los existentes para los ensayos realizados con hormigón. El modelo reológico que se ha obtenido por ajuste de todo el período anterior, consta de cuatro celdas de Kelvin y predice igualmente la deformación por fluencia de la roca. La correcta evaluación de las deformaciones a largo plazo es necesaria siempre que se estudie la intervención en edificaciones históricas, bien sea variando la distribución de cargas, o simplemente realizando obras de mantenimiento de cierto calado. La influencia de la temperatura alcanzada y del proceso de enfriamiento utilizado, se ha analizado sobre 55 muestras de roca calentando a temperaturas de hasta 600 ºC y enfriando por dos métodos: al aire y mediante inmersión en agua, ambas a temperatura ambiente. Los parámetros controlados antes y después del proceso térmico han sido: porosidades abierta y total velocidad de propagación de ondas ultrasónicas, módulo de elasticidad, coeficiente de Poisson, resistencia a compresión uniaxial (UCS) y durabilidad según el ensayo de sequedad, humedad y desmoronamiento, Slake Durability Test (SDT). Como conclusiones más notables cabe destacar: la UCS disminuye en un 35% y en un 5O% según el enfriamiento se haya realizado al aire o por inmersión, mientras que el módulo de elasticidad se reduce entre un 75% y un 80%. Las conclusiones obtenidas son importantes para la determinación del daño estructural producido en un incendio, así como para evaluar la influencia del método de extinción. Por otra parte, pueden servir para estimar indirectamente la temperatura máxima alcanzada en un incendio, de cara a la determinación de los posibles efectos sobre otros elementos constructivos. Para la relación entre módulos estáticos y dinámicos se han estudiado 24 muestras con diferentes grados de deterioro. Con los datos obtenidos en los ensayos se han analizado estadísticamente quince modelos de relación con diferentes combinaciones de variables, y se ha construido la correspondiente matriz de correlación. El coeficiente de determinación más alto corresponde a una relación lineal entre ambos módulos. La determinación del módulo de elasticidad por medios no destructivos y de fácil implementación es muy útil cuando se trata de dictaminar sobre el envejecimiento de un material estructural de este tipo. El valor del módulo con respecto al de la roca intacta es un indicador de las características resistentes y grado de debilitamiento del material. Sin embargo, el módulo bajo cargas gravitatorias -estáticas- difiere en general del obtenido dinámicamente, de una manera diferente según el material que se analice. Aquí se ha obtenido una expresión, que correlaciona con un alto valor del coeficiente de determinación ambos módulos, para la roca estudiada. Los parámetros, relaciones y modelos estudiados y propuestos en esta tesis, suponen un importante avance científico de gran utilidad para la conservación y restauración del patrimonio de edificios y otras obras de carácter histórico-cultural construidas con la Piedra de San Julián. Asimismo, las conclusiones obtenidas y los medios y métodos empleados podrán ser extrapolados a otros materiales similares con las adaptaciones oportunas.

Moisture Distribution in Partially Saturated Concrete Studied by Impedance Spectroscopy

The moisture content and its spatial distribution has a great influence on the durability properties of concrete structures. Several non-destructive techniques have been used for the determination of the total water content, but moisture distribution is difficult to determine. In this paper impedance spectroscopy is used to study the water distribution in concrete samples with controlled and homogeneously distributed moisture contents. The technique is suitable for the determination of water distribution inside the sample, using the appropriate equivalent circuits. It is shown that using the selected drying procedures there is no change in the solid phase of the samples, although the technique can only be used for the qualitative study of variations in the solid phase when samples are too thick. The results of this work show that for a wide range of concrete percentages of saturation, from full to 18 % saturation, practically all the pores keep at least a thin layer of electrolyte covering their walls, since the capacitance measurement results are practically independent of the saturation degree.

An approach for characterising the weathering behaviour of Flysch slopes applied to the carbonatic Flysch of Alicante (Spain)

Various studies indicate that most of the slope instabilities affecting Flysch heterogeneous rock masses are related to differential weathering of the lithologies that make up the slope. Therefore, the weathering characteristics of the intact rock are of great importance for the study of these types of slopes and their associated instability processes. The main aim of this study is to characterise the weathering properties of the different lithologies outcropping in the carbonatic Flysch of Alicante (Spain), in order to understand the effects of environmental weathering on them, following slope excavation. To this end, 151 strata samples obtained from 11 different slopes, 5–40 years old, were studied. The lithologies were identified and their mechanical characteristics obtained using field and laboratory tests. Additionally, the slaking properties of intact rocks were determined, and a classification system proposed based on the first and fifth slake cycles (Id1 and Id5 respectively) and an Index of Weathering (IW5), defined in the study. Information obtained from the laboratory and the field was used to characterise the weathering behaviour of the rocks. Furthermore, the slaking properties determined from laboratory tests were related to the in-situ weathering properties of rocks (i.e., the weathering profile, patterns and length, and weathering rate). The proposed relationship between laboratory test results, field data, and in-situ observations provides a useful tool for predicting the response of slopes to weathering after excavation during the preliminary stages of design.

Proposal of a New Parameter for the Weathering Characterization of Carbonate Flysch-Like Rock Masses: The Potential Degradation Index (PDI)

The susceptibility of clay bearing rocks to weathering (erosion and/or differential degradation) is known to influence the stability of heterogeneous slopes. However, not all of these rocks show the same behaviour, as there are considerable differences in the speed and type of weathering observed. As such, it is very important to establish relationships between behaviour quantified in a laboratory environment with that observed in the field. The slake durability test is the laboratory test most commonly used to evaluate the relationship between slaking behaviour and rock durability. However, it has a number of disadvantages; it does not account for changes in shape and size in fragments retained in the 2 mm sieve, nor does its most commonly used index (Id2) accurately reflect weathering behaviour observed in the field. The main aim of this paper is to propose a simple methodology for characterizing the weathering behaviour of carbonate lithologies that outcrop in heterogeneous rock masses (such as Flysch slopes), for use by practitioners. To this end, the Potential Degradation Index (PDI) is proposed. This is calculated using the fragment size distribution curves taken from material retained in the drum after each cycle of the slake durability test. The number of slaking cycles has also been increased to five. Through laboratory testing of 117 samples of carbonate rocks, extracted from strata in selected slopes, 6 different rock types were established based on their slaking behaviour, and corresponding to the different weathering behaviours observed in the field.

Ventilated Stone Veneer: Mechanical Behaviour, Calculation Methodologies, Major Pathologies and Existing Tests

The increase of building pathologies related to the use of stone materials and the use of ventilated stone veneers, requires the reformulation of design concepts in building façades and also the reformulation of the architectural project. The aim of this paper is to identify, analyze and evaluate synthetically building pathologies in stone ventilated façades in order to obtain the main technical conditions to be considered in the architectural design, by interpreting its mechanical behavior and capabilities to prevent such pathologies and to ensure the proper features during the building lifetime. The methodology is based on both laboratory stone tests and in situ tests about construction systems, by analyzing physical and mechanical behavior of the outer layer in relation to other building requirements. The results imply the need of proper sizing, specific quality control and practical application of calculation methods, to control high concentration pressures in ventilated façades by reaching appropriate project solutions. In conclusion, the research about different pathologies of stone ventilated façades, the study of their mechanical behavior, their anchorage and their connection with their constructive aspects, will help to improve the construction quality of the stone ventilated façade in buildings and to enhance the use of natural stone in modern architecture.