Catalytic effect of MCM-41 in the pyrolysis of tobacco and several substances used as additives in the preparation of commercial cigarettes

Comunicación presentada en forma de póster en el "12th Mediterranean Congress of Chemical Engineering", Barcelona (Spain), November 15-18, 2011.

TGA/FTIR study of the MCM-41-catalytic pyrolysis of tobacco and tobacco–glycerol mixtures

In this work, the catalytic effect of MCM-41 on the qualitative composition of the gases evolved in the pyrolysis of glycerol, tobacco and tobacco–glycerol mixtures has been studied by TGA/FTIR. The results obtained reflect that the amount of volatile products obtained from tobacco or from tobacco containing mixtures is noticeably decreased if the catalyst is used as a tobacco additive. The addition of the catalyst also produces noticeable changes in the composition of the gases obtained at each temperature. Such changes are more significant in the case of the pyrolysis of the tobacco–glycerol–mixture than in the pyrolysis of tobacco. The evolution patterns for different types of compounds reveal that the catalyst contributes to a noticeable decrease of the yields of methane, CO, CO2 and carbonylic compounds, which could be interesting from the point of view of the use of MCM-41 as a tobacco additive in order to reduce tobacco smoke toxicity.

TGA/FTIR study of tobacco and glycerol–tobacco mixtures

In this work, the evolution with temperature of the qualitative composition of the gases evolved in the pyrolysis of glycerol, tobacco and tobacco–glycerol mixtures has been studied. The pathways for different types of compounds (i.e., water, CO, CO2, carbonylic compounds, alkenyl or alkyl groups containing compounds, alcohols and phenols and aromatic compounds) have been established, and their relationship with the different reaction steps involved in the pyrolysis process have been suggested. The comparison among the behavior observed in the pyrolysis of tobacco, glycerol and a mixture glycerol–tobacco has permitted us to suggest possible interactions between tobacco and glycerol affecting the composition of the gases evolved.

New Measures Envisaged by Spanish Legislation in Support of the Internationalization of Companies

Medidas tributarias para fomentar la internacionalización de las empresas.

Reduction of tobacco smoke components yield in commercial cigarette brands by addition of HUSY, NaY and Al-MCM-41 to the cigarette rod

The effect of two zeolites, HUSY, NaY and a mesoporous synthesized Al-MCM-41 material on the smoke composition of ten commercial cigarettes brands has been studied. Cigarettes were prepared by mixing the tobacco with the three powdered materials, and the smoke obtained under the ISO conditions was analyzed. Up to 32 compounds were identified and quantified in the gas fraction and 80 in the total particulate matter (TPM) condensed in the cigarettes filters and in the traps located after the mouth end of the cigarettes. Al-MCM-41 is by far the best additive, providing the highest reductions of the yield for most compounds and brands analyzed. A positive correlation was observed among the TPM and nicotine yields with the reduction obtained in nicotine, CO, and most compounds with the three additives. The amount of ashes in additive free basis increases due to the coke deposited on the solids, especially with Al-MCM-41. Nicotine is reduced with Al-MCM-41 by an average of 34.4% for the brands studied (49.5% for the brand where the major reduction was obtained and 18.5 for the brand behaving the worst). CO is reduced by an average of 18.6% (ranging from 10.3 to 35.2% in the different brands).

Comparison between the mainstream smoke of eleven RYO tobacco brands and the reference tobacco 3R4F

In this study 11 commercial roll-your-own (RYO) tobacco brands sold in Spain and the reference tobacco 3R4F have been smoked and several components of the mainstream tobacco smoke have been analyzed. Cigarettes were prepared using commercial tubes, and were smoked under smoking conditions based on the ISO 3308. The gaseous and condensed fractions of the smoke from RYO brands and 3R4F have been analyzed and compared. RYO tobaccos, as opposed to 3R4F, present lower amounts of condensed products in the traps than in the filters. In general, RYO tobaccos also provide lower yields of most of the compounds detected in the gas fraction. The yield of CO is between 15.4 and 20.4 mg/cigarette. In most of the cases studied, RYO tobaccos deliver higher amounts of nicotine than the 3R4F tobacco. On average, the yield of the different chemical families of compounds appearing in the particulate matter retained in the cigarette filters tends to be around three times higher than those obtained from 3R4F, whereas similar values have been obtained in the particulate matter retained in the traps located after the filters. It can be concluded that RYO tobaccos are not less hazardous than the reference tobacco, which may be contrary to popular belief.

The Big BIM battle: BIM adoption in the UK for large and small companies

As BIM adoption continues, the goal of a totally collaborative model with multiple contributors is attainable. Many initiatives such as the 2016 UK government level 2 BIM deadline are putting pressure on the construction industry to speed up the changeover. Clients and collaborators have higher expectations of using digital 3D models to communicate design ideas and solve practical problems. Contractors and clients are benefitting from cost saving scheduling and clash detection offered by BIM. Effective collaboration on the project will also give speed and efficiency gains. Despite this, many businesses of varying sizes are still having problems. The cost of the software and the training provides an obvious barrier for micro-enterprises and could explain a delay in adoption. Many studies have looked at these problems faced by SME and micro-enterprises. Larger companies have different problems. The efforts made by government to encourage them are quite comprehensive, but is anything being done to help smaller sectors and keep the industry cohesive? This limited study examines several companies of varying size and varying project type: architectural design businesses, main contractor, structural engineer and building consultancy. The study examines the barriers to a truly collaborative BIM workflow facing different specialities on a larger project and a contrasting small/medium project. The findings will establish that different barriers for each sector are actually pushing further apart, thus potentially creating a BIM-only construction elite, leaving the small companies remaining on 2D based drawing.