Diseño de la asignatura Trabajo Fin de Grado en Geología (Facultad de Ciencias, UA)

Con la implantación en el año académico 2013-14 del cuarto y último curso del grado en Geología en la Universidad de Alicante, se ha implementado la asignatura obligatoria de Trabajo Fin de Grado en Geología (TFGG) con el objetivo de que el estudiante demuestre las competencias adquiridas durante sus estudios de geología, tanto las específicas de la titulación, como las competencias generales o transversales, tal como son las ligadas a la búsqueda y organización de documentación, a la redacción clara y concisa de una memoria escrita que recoja un trabajo original del alumno y a la presentación en público de su trabajo de manera clara y adecuada. Siguiendo las directrices que se establecen, tanto en la Facultad de Ciencias, como en la Universidad de Alicante se ha diseñado una asignatura Trabajo Fin de Grado con varias modalidades o líneas de actividad docente. Se ha constituido una Comisión de Trabajo de Fin de Grado en Geología (CTFGG) con el propósito principal de organizar y supervisar la asignación, seguimiento y evaluación de los trabajos.

Tasas de deformación GPS en la cuenca del Bajo Segura (Cordillera Bética oriental)

En este trabajo hemos cuantificado las tasas de deformación actual de la cuenca del Bajo Segura (NE del corredor de cizalla de la Bética oriental), a partir del análisis de una red GPS con 11 vértices geodésicos. Se han analizado los datos de cuatro campañas GPS entre junio de 1999 y enero de 2013, que han sido procesados con la versión 6.2 del software GIPSY-OASIS. Este software utiliza la técnica de posicionamiento puntual de precisión conocido por las siglas PPP. Se observa un acortamiento ~N-S en toda la cuenca de mayor magnitud en el sur, en la zona de falla del Bajo Segura, con valores que varían de oeste a este entre 0,73 y 0,24 mm/año. En el borde septentrional de la cuenca, en la zona de falla de Crevillente, los valores de acortamiento N-S son menores. Sin embargo, en esta falla se ha observado un movimiento lateral sinistrorso que, en la componente E-O, varía entre 0,44 y 0,75 mm/año.

Development and programming of Geophonino: A low cost Arduino-based seismic recorder for vertical geophones

The commercial data acquisition systems used for seismic exploration are usually expensive equipment. In this work, a low cost data acquisition system (Geophonino) has been developed for recording seismic signals from a vertical geophone. The signal goes first through an instrumentation amplifier, INA155, which is suitable for low amplitude signals like the seismic noise, and an anti-aliasing filter based on the MAX7404 switched-capacitor filter. After that, the amplified and filtered signal is digitized and processed by Arduino Due and registered in an SD memory card. Geophonino is configured for continuous registering, where the sampling frequency, the amplitude gain and the registering time are user-defined. The complete prototype is an open source and open hardware system. It has been tested by comparing the registered signals with the ones obtained through different commercial data recording systems and different kind of geophones. The obtained results show good correlation between the tested measurements, presenting Geophonino as a low-cost alternative system for seismic data recording.

Fortification and Frontier: The Project Drawn up by Juan Martín Zermeño for Puebla de Sanabria in 1766

Following the death of engineer General Jorge Próspero de Verboom in 1744 and after a few years of transition in the management of Spanish fortifications, Juan Martín Zermeño took on the role, initially with a temporary mandate, but then definitively during a second period that ran from 1766 until his death in 1772. He began this second period with a certain amount of concern because of what had taken place during the last period of conflict. The Seven Years War (1756–1763) which had brought Spain into conflict with Portugal and England in the Caribbean had also lead to conflict episodes along the Spanish–Portuguese border. Zermeño’s efforts as a planner and general engineer gave priority to the northern part of the Spanish–Portuguese border. After studying the territory and the existing fortifications on both sides of the border, Zermeño drew up three important projects in 1766. The outposts that needed to be reinforced were located, from north to south, at Puebla de Sanabria, Zamora and Ciudad Rodrigo, which is where he is believed to have come from. This latter township already had a modern installation built immediately after the war of the Spanish Succession and reinforced with the Fort of La Concepción. However, Zamora and Puebla de Sanabria had some obsolete fortifications that needed modernising. Since the middle of the 15th century Puebla de Sanabria had had a modern castle with rounded turrets, that of the counts of benavente. During the 16th and 17th centuries it had also been equipped with a walled enclosure with small bastions. During the war of the Spanish Succession the Portuguese had enlarged the enclosure and had erected a tentative offshoot to the west. In order to draw up the ambitious Puebla de Sanabria project Zermeño had the aid of some previous reports and projects, such as those by the count of robelin in 1722, the one by Antonio de Gaver in 1752, and Pedro Moreau’s report dated June 1755. This study includes a technical analysis of Zermeño’s project and its strategic position within the system of fortifications along the Spanish–Portuguese border.