Simultaneous synthesis of heat exchanger networks with pressure recovery: optimal integration between heat and work

The optimal integration between heat and work may significantly reduce the energy demand and consequently the process cost. This paper introduces a new mathematical model for the simultaneous synthesis of heat exchanger networks (HENs) in which the pressure levels of the process streams can be adjusted to enhance the heat integration. A superstructure is proposed for the HEN design with pressure recovery, developed via generalized disjunctive programming (GDP) and mixed-integer nonlinear programming (MINLP) formulation. The process conditions (stream temperature and pressure) must be optimized. Furthermore, the approach allows for coupling of the turbines and compressors and selection of the turbines and valves to minimize the total annualized cost, which consists of the operational and capital expenses. The model is tested for its applicability in three case studies, including a cryogenic application. The results indicate that the energy integration reduces the quantity of utilities required, thus decreasing the overall cost.

MINLP Optimization Algorithm for the Synthesis of Heat and Work Exchange Networks

This paper introduces a new optimization model for the simultaneous synthesis of heat and work exchange networks. The work integration is performed in the work exchange network (WEN), while the heat integration is carried out in the heat exchanger network (HEN). In the WEN synthesis, streams at high-pressure (HP) and low-pressure (LP) are subjected to pressure manipulation stages, via turbines and compressors running on common shafts and stand-alone equipment. The model allows the use of several units of single-shaft-turbine-compressor (SSTC), as well as helper motors and generators to respond to any shortage and/or excess of energy, respectively, in the SSTC axes. The heat integration of the streams occurs in the HEN between each WEN stage. Thus, as the inlet and outlet streams temperatures in the HEN are dependent of the WEN design, they must be considered as optimization variables. The proposed multi-stage superstructure is formulated in mixed-integer nonlinear programming (MINLP), in order to minimize the total annualized cost composed by capital and operational expenses. A case study is conducted to verify the accuracy of the proposed approach. The results indicate that the heat integration between the WEN stages is essential to enhance the work integration, and to reduce the total cost of process due the need of a smaller amount of hot and cold utilities.

Optimization of test and maintenance of ageing components consisting of multiple items and addressing effectiveness

There are many models in the literature that have been proposed in the last decades aimed at assessing the reliability, availability and maintainability (RAM) of safety equipment, many of them with a focus on their use to assess the risk level of a technological system or to search for appropriate design and/or surveillance and maintenance policies in order to assure that an optimum level of RAM of safety systems is kept during all the plant operational life. This paper proposes a new approach for RAM modelling that accounts for equipment ageing and maintenance and testing effectiveness of equipment consisting of multiple items in an integrated manner. This model is then used to perform the simultaneous optimization of testing and maintenance for ageing equipment consisting of multiple items. An example of application is provided, which considers a simplified High Pressure Injection System (HPIS) of a typical Power Water Reactor (PWR). Basically, this system consists of motor driven pumps (MDP) and motor operated valves (MOV), where both types of components consists of two items each. These components present different failure and cause modes and behaviours, and they also undertake complex test and maintenance activities depending on the item involved. The results of the example of application demonstrate that the optimization algorithm provide the best solutions when the optimization problem is formulated and solved considering full flexibility in the implementation of testing and maintenance activities taking part of such an integrated RAM model.

Gender inequalities in occupational health related to the unequal distribution of working and employment conditions: a systematic review

Introduction: Gender inequalities exist in work life, but little is known about their presence in relation to factors examined in occupation health settings. The aim of this study was to identify and summarize the working and employment conditions described as determinants of gender inequalities in occupational health in studies related to occupational health published between 1999 and 2010. Methods: A systematic literature review was undertaken of studies available in MEDLINE, EMBASE, Sociological Abstracts, LILACS, EconLit and CINAHL between 1999 and 2010. Epidemiologic studies were selected by applying a set of inclusion criteria to the title, abstract, and complete text. The quality of the studies was also assessed. Selected studies were qualitatively analysed, resulting in a compilation of all differences between women and men in the prevalence of exposure to working and employment conditions and work-related health problems as outcomes. Results: Most of the 30 studies included were conducted in Europe (n=19) and had a cross-sectional design (n=24). The most common topic analysed was related to the exposure to work-related psychosocial hazards (n=8). Employed women had more job insecurity, lower control, worse contractual working conditions and poorer self-perceived physical and mental health than men did. Conversely, employed men had a higher degree of physically demanding work, lower support, higher levels of effort-reward imbalance, higher job status, were more exposed to noise and worked longer hours than women did. Conclusions: This systematic review has identified a set of working and employment conditions as determinants of gender inequalities in occupational health from the occupational health literature. These results may be useful to policy makers seeking to reduce gender inequalities in occupational health, and to researchers wishing to analyse these determinants in greater depth.

Online Media and Crisis? of Advertising Media Planning

Nowadays, online media represent a great choice for advertising. From de advertising media planning, new media give new ways to reach the consumers, but they also add more complexity. The communication capacity of online media and the greater use of that media by part of the users open up the debate about the necessity of rethinking the approach of the ‘traditional’ advertising media planning, which structure and work processes were developed when media were offline. So, this article gives a panoramic view about the influence of new media in advertising media planning. To do this, in first place, describes the current scenario, analyzing the penetration and advertising expenditure in Internet. Also, it shows the main online media according to their proximity to the offline advertising media planning conception. In second place, this article addresses the current challenges at measuring new media as a symptom of the impulse at the change of model. Finally, the article ends up showing some trends that are presented as drivers of change. However, after this analysis, comes up the point that those aspects would not change the essence of advertising media planning, so it is questionable if we can speak of a crisis or, instead, if new media are showing the necessity that media planning have to be involved with this new scenario.

Intelligent Decision-Making System Frameworks for a Digital Plan of Work: A Theoretical Investigation for the Construction Industry

The construction industry is characterised by fragmentation and suffers from lack of collaboration, often adopting adversarial working practices to achieve deliverables. For the UK Government and construction industry, BIM is a game changer aiming to rectify this fragmentation and promote collaboration. However it has become clear that there is an essential need to have better controls and definitions of both data deliverables and data classification. Traditional methods and techniques for collating and inputting data have shown to be time consuming and provide little to improve or add value to the overall task of improving deliverables. Hence arose the need in the industry to develop a Digital Plan of Work (DPoW) toolkit that would aid the decision making process, providing the required control over the project workflows and data deliverables, and enabling better collaboration through transparency of need and delivery. The specification for the existing Digital Plan of Work (DPoW) was to be, an industry standard method of describing geometric, requirements and data deliveries at key stages of the project cycle, with the addition of a structured and standardised information classification system. However surveys and interviews conducted within this research indicate that the current DPoW resembles a digitised version of the pre-existing plans of work and does not push towards the data enriched decision-making abilities that advancements in technology now offer. A Digital Framework is not simply the digitisation of current or historic standard methods and procedures, it is a new intelligent driven digital system that uses new tools, processes, procedures and work flows to eradicate waste and increase efficiency. In addition to reporting on conducted surveys above, this research paper will present a theoretical investigation into usage of Intelligent Decision Support Systems within a digital plan of work framework. Furthermore this paper will present findings on the suitability to utilise advancements in intelligent decision-making system frameworks and Artificial Intelligence for a UK BIM Framework. This should form the foundations of decision-making for projects implemented at BIM level 2. The gap identified in this paper is that the current digital toolkit does not incorporate the intelligent characteristics available in other industries through advancements in technology and collation of vast amounts of data that a digital plan of work framework could have access to and begin to develop, learn and adapt for decision-making through the live interaction of project stakeholders.

Digital Fabrication and Free Culture. One More Minor Becoming?

Diferentes autores se refieren a la fabricación digital como la Tercera Revolución Digital, después de las revoluciones de la computación y la comunicación. Como ocurriera con las dos revoluciones precedentes, se generaron grandes expectativas en torno a las virtualidades políticas de estas nuevas tecnologías para dar lugar a relaciones de producción más libres e individuos más autónomos. Sin embargo, como también ocurriera con la computación y la comunicación, lo que realmente está ocurriendo demuestra que las supuestas virtualidades no llegarán a hacerse actuales sin una intensa implicación, organización y trabajo por parte de sectores activistas técnicos y sociales. Se discute el caso de la compra corporativa de la empresa pionera de hardware libre Makerbot, como ejemplo de la situación y punto de inflexión en las expectativas de los nuevos tecno-visionarios. Para concluir se propone una serie de posibles estrategias que podrían promover el desarrollo efectivo de un ecosistema libre y open source de fabricación digital.