Changes to porcine blastocyst vitrification methods and improved litter size after transfer

The objective was to improve the protocol that was used to obtain the first reported piglets from transferred vitrified and warmed zona-intact blastocysts. Blastocysts were collected from superovulated sows and gilts, centrifuged to polarize lipid, vitrified, warmed and cultured for 24 h or transferred immediately. Removing the zona pellucida after warming increased the number of cells in the surviving blastocysts (zona-free 60.8 +/- 4.3, zona-intact 39.1 +/- 2.8; P < 0.05). Thinning the zona pellucida produced similar results to zona removal. Changing the basal medium of the vitrification and warming solutions from modified PBS to phosphate buffered NCSU-23 increased the number of cells (44.7 +/- 2.2 versus 56.0 +/- 3.9, respectively; P < 0.05). Reducing the plunge temperature of the liquid nitrogen from - 196 degrees C to less than -204 degrees C improved the embryo survival rate (61.9% versus 82.9%, respectively; P < 0.05). These modifications were incorporated into the vitrification protocol that was used to vitrify and warm 105 blastocysts (that were subsequently transferred into four recipients). Three recipients became pregnant, farrowing three litters (average litter size, 5.3; 18.8% embryo survival in farrowing sows). Changing the warming protocol to using sucrose rather than ethylene glycol resulted in a trend towards improved embryo survival (73.5% versus 91.2%) but this was not statistically significant. Incorporating this modification, 203 blastocysts were vitrified, warmed and transferred into seven recipients. Five became pregnant and 36 fetuses were recovered (average litter size 7.2; 24.8% embryo survival in pregnant sows) at Day 40 of pregnancy. In conclusion, changes made to the vitrification protocol improved pregnancy rate and in vivo embryo survival compared to an earlier study using the original protocol. (c) 2005 Elsevier Inc. All rights reserved.

Precipitation hardening of Cu-Fe-Cr alloys - Part I - Mechanical and electrical properties

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. The literature indicated that Cu rich Cu-Cr and Cu-Fe alloys have been thoroughly investigated. A number of commercial alloys have been developed and these are used for a variety of applications requiring combinations of high-strength, high-conductivity and resistance to softening. Little evidence was found in the literature that the Cu rich corner of the Cu-Fe-Cr system had previously been investigated for the purpose of developing high-strength, high-conductivity copper alloys resistant to softening. The aim of these present investigations was to explore the possibility that new alloys could be developed that combined the properties of both sets of alloys, ie large precipitation hardening response combined with the ability to stabilise cold worked microstructures to high temperatures while at the same maintain high electrical conductivity. To assess the feasibility of this goal the following alloys were chosen for investigation: Cu-0.7wt%Cr-0.3wt%Fe, Cu-0.7wt%Cr-0.8wt%Fe, Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the mechanical property investigation which indicated that the Cu-0.7wt%Cr-0.3wt%Fe, and Cu-0.7wt%Cr-2.0wt%Fe alloys were worthy of further investigation. (C) 2001 Kluwer Academic Publishers.

Precipitation hardening of Cu-Fe-Cr alloys - Part II - Microstructural characterisation

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. Promising properties have been measured for the following alloys: Cu-0.7wt%Cr-0.3wt%Fe and Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the microstructural characterisation of these alloys and discusses the mechanical and electrical properties of these alloys in terms of their microstructure, particularly the formation of precipitates. These alloys have evinced properties that warrant further investigation. Cost modelling has shown that Cu-0.7wt%Cr-0.3wt%Fe is approximately 25% cheaper to produce than commercial Cu-1%Cr. It has also been shown to be more cost efficient on a yield stress and % IACS per dollar basis. The reason for the cost saving is that the Cu-0.7%Cr-0.3%Fe alloy can be made with low carbon ferro-chrome additions as the source of chromium rather than the more expensive Cu-Cr master-alloy. For applications in which cost is one of the primary materials selection criteria, it is envisaged that there would be numerous applications in both cast and wrought form, where the Cu-0.7%Cr-0.3%Fe alloy would be more suitable than Cu-1%Cr. (C) 2001 Kluwer Academic Publishers.

An age hardening model for Al-7Si-Mg casting alloys

Yield strength (YS) ageing curves have been modelled for A356 and A357 aluminium casting alloys below the solvus temperature of the main hardening precipitate. Predictions are based on the Shercliff and Ashby methodology (Acta MetaH. Mater. 38 (1990) 1789) for wrought alloys. Differences between strengthening in wrought and cast Al-Si-Mg alloys are considered. A Brinell hardness to YS conversion incorporating strain hardening has been established to enable YS ageing curves to be predicted with reduced experimental effort. (C) 2002 Elsevier Science B.V. All rights reserved.