Inter- and intralaboratory variation of in vitro diffusion cell measurements: An international multicenter study using quasi-standardized methods and materials

In vitro measurements of skin absorption are an increasingly important aspect of regulatory studies, product support claims, and formulation screening. However, such measurements are significantly affected by skin variability. The purpose of this study was to determine inter- and intralaboratory variation in diffusion cell measurements caused by factors other than skin. This was attained through the use of an artificial (silicone rubber) rate-limiting membrane and the provision of materials including a standard penetrant, methyl paraben (MP), and a minimally prescriptive protocol to each of the 18 participating laboratories. Standardized calculations of MP flux were determined from the data submitted by each laboratory by applying a predefined mathematical model. This was deemed necessary to eliminate any interlaboratory variation caused by different methods of flux calculations. Average fluxes of MP calculated and reported by each laboratory (60 +/- 27 mug cm(-2) h(-1), n = 25, range 27-101) were in agreement with the standardized calculations of MP flux (60 +/- 21 mug cm(-2) h(-1), range 19-120). The coefficient of variation between laboratories was approximately 35% and was manifest as a fourfold difference between the lowest and highest average flux values and a sixfold difference between the lowest and highest individual flux values. Intra-laboratory variation was lower, averaging 10% for five individuals using the same equipment within a single laboratory. Further studies should be performed to clarify the exact components responsible for nonskin-related variability in diffusion cell measurements. It is clear that further developments of in vitro methodologies for measuring skin absorption are required. (C) 2005 Wiley-Liss, Inc.

Applicability of experience from laboratory reactors with biological phosphorus removal in full-scale plants

Enhanced biological phosphorus removal (EBPR) has been used at many wastewater treatment plants all over the world for many years. In this study a full-scale sludge with good EBPR was tested with P-release batch tests and combined FISH/MAR (fluorescence in situ hybridisation and microautoradiography). Proposed models of PAOs and GAOs (polyphosphate- and glycogen-accumulating organisms) and microbial methods suggested from studies of laboratory reactors were found to be applicable also on sludge from full-scale plants. Dependency of pH and the uptake of both acetate and propionate were studied and used for calculations for verifying the models and results from microbial methods. All rates found from the batch tests with acetate were higher than in the batch tests with propionate, which was explained by the finding that only those parts of the bacterial community that were able to take up acetate anaerobically were able to take up propionate anaerobically.

Laboratory-based simulation of freezing profiles of beef trim for Escherichia coli O157 survival determinations

This study was undertaken to develop a simple laboratory-based method for simulating the freezing profiles of beef trim so that their effect on E. coli 0157 survival could be better assessed. A commercially available apparatus of the type used for freezing embryos, together with an associated temperature logger and software, was used for this purpose with a -80 degrees C freezer as a heat sink. Four typical beef trim freezing profiles, of different starting temperatures or lengths, were selected and modelled as straight lines for ease of manipulation. A further theoretical profile with an extended freezing plateau was also developed. The laboratory-based setup worked well and the modelled freezing profiles fitted closely to the original data. No change in numbers of any of the strains was apparent for the three simulated profiles of different lengths starting at 25 degrees C. Slight but significant (P < 0.05) decreases in numbers (similar to 0.2 log cfu g(-1)) of all strains were apparent for a profile starting at 12 degrees C. A theoretical version of this profile with a freezing plateau phase extended from 11 h to 17 h resulted in significant (P < 0.05) decreases in numbers (similar to 1.2 log cfu g(-1)) of all strains. Results indicated possible avenues for future research in controlling this pathogen. The method developed in this study proved a useful and cost-effective way for simulating freezing profiles of beef trim. (c) 2005 Elsevier B.V. All rights reserved.

Particle tracking in a salinity gradient: A method for measuring sinking rate of individual phytoplankton in the laboratory

This paper presents a new method to measure the sinking rates of individual phytoplankton “particles” (cells, chains, colonies, and aggregates) in the laboratory. Conventional particle tracking and high resolution video imaging were used to measure particle sinking rates and particle size. The stabilizing force of a very mild linear salinity gradient (1 ppt over 15 cm) prevented the formation of convection currents in the laboratory settling chamber. Whereas bulk settling methods such as SETCOL provide a single value of sinking rate for a population, this method allows the measurement of sinking rate and particle size for a large number of individual particles or phytoplankton within a population. The method has applications where sinking rates vary within a population, or where sinking rate-size relationships are important. Preliminary data from experiments with both laboratory and field samples of marine phytoplankton are presented here to illustrate the use of the technique, its applications, and limitations. Whereas this paper deals only with sinking phytoplankton, the method is equally valid for positively buoyant species, as well as nonbiological particles.