Suitability of acoustic perturbation measures in analysing periodic and nearly periodic voice signals

In recent years, acoustic perturbation measurement has gained clinical and research popularity due to the ease of availability of commercial acoustic analysing software packages in the market. However, because the measurement itself depends critically on the accuracy of frequency tracking from the voice signal, researchers argue that perturbation measures are not suitable for analysing dysphonic voice samples, which are aperiodic in nature. This study compares the fundamental frequency, relative amplitude perturbation, shimmer percent and noise-to-harmonic ratio between a group of dysphonic and non-dysphonic subjects. One hundred and twelve dysphonic subjects ( 93 females and 19 males) and 41 non-dysphonic subjects ( 35 females and 6 males) participated in the study. All the 153 voice samples were categorized into type I ( periodic or nearly periodic), type II ( signals with subharmonic frequencies that approach the fundamental frequency) and type III ( aperiodic) signals. Only the type I ( periodic and nearly periodic) voice signals were acoustically analysed for perturbation measures. Results revealed that the dysphonic female group presented significantly lower fundamental frequency, significantly higher relative amplitude perturbation and shimmer percent values than the non-dysphonic female group. However, none of these three perturbation measures were able to differentiate between male dysphonic and male non-dysphonic subjects. The noise-to-harmonic ratio failed to differentiate between the dysphonic and non-dysphonic voices for both gender groups. These results question the sensitivity of acoustic perturbation measures in detecting dysphonia and suggest that contemporary acoustic perturbation measures are not suitable for analysing dysphonic voice signals, which are even nearly periodic. Copyright (C) 2005 S. Karger AG, Basel.

Evaluation of the indirect measures of rock brittleness and fracture toughness in rock cutting

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, and B4) were calculated for sandstones samples, whereas a toughness index (T-i), being developed by Atkinson et al.(1), was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student's t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell(2) and Roxborough and Philips(3) have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and T-i. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

The risk premium for equity: implications for resource allocation, welfare and policy

Analysis of the equity premium puzzle has focused on private sector capital markets. The object of this paper is to consider the welfare and policy implications of each of the broad classes of explanations of the equity premium puzzle. As would be expected, the greater the deviation from the first-best outcome implied by a given explanation of the equity premium puzzle, the more interventionist are the implied policy conclusions. Nevertheless, even explanations of the equity premium puzzle consistent with a general consumption-based asset pricing model have important welfare and policy implications.

Legislative and regulatory measures for preventing alcohol-related drownings and near-drownings

Objective: Alcohol contributes to about 30% of drowning fatalities associated with recreational aquatic activity and to 35% of drownings associated with boating. We consider regulatory and legislative strategies for preventing such deaths. Methods: We contacted water police in each Australian State and Territory to identify legislation creating alcohol-related offences for operators of recreational boats in their jurisdiction and to determine whether they conducted random breath testing (RBT). We also sought information from all 152 (81 urban and 71 rural) local government councils in NSW regarding restrictions on consumption of alcohol in public places within their shires. Results: Four Australian States (New South Wales, Queensland, Victoria and South Australia) have legislation prescribing maximum blood alcohol concentrations (BACs) for operators of recreational boats; all support this with RBT Western Australia, Tasmania and the Australian Capital Territory define more general offences for operating vessels while under the influence, of alcohol. Prohibitions or restrictions on consumption of alcohol in public places exist in 78 of the 86 shires in NSW that responded: 69 councils had alcohol-free zones, 53 restricted consumption of alcohol in public parks and reserves, and 33 had prohibitions or restrictions in some aquatic environments. Conclusions/implications: Legislation restricting BACs for recreational boat operators should be adopted in all Australian States and Territories. Optimal legislation would require that all occupants of recreational boats are required to comply with prescribed BAC levels, including when vessels are at anchor. Extension of by-laws prohibiting or restricting the consumption of alcohol specifically in aquatic environments warrants consideration.