An investigation of magnetic antennas for ground penetrating radar

For ground penetrating radar (GPR), smaller antennas would provide considerable practical advantages. Some of which are: portability; ease of use; and higher spatial sampling. A theoretical comparison of the fundamental limits of a small electric field antenna and a small magnetic field antenna shows that the minimum Q constraints are identical. Furthermore, it is shown that only the small magnetic loop antenna can be constructed to approach, arbitrarily closely, the fundamental minimum Q limit. This is achieved with the addition of a high permeability material which reduces energy stored in the magnetic fields. This is of special interest to some GPR applications. For example, applications requiring synthetic aperture data collection would benefit from the increased spatial sampling offered by electrically smaller antennas. Low frequency applications may also benefit, in terms of reduced antenna dimensions, by the use of electrically small antennas. Under these circumstances, a magnetic type antenna should be considered in preference to the typical electric field antenna. Numerical modeling data supports this assertion.

Long-term persistence of multi-drug-resistant Salmonella enterica serovar Newport in two dairy herds

Objective - To evaluate the association between maintaining joint hospital and maternity pens;and persistence of multi-drug-resistant (MDR) Salmonella enterica serovar Newport on 2 dairy farms. Design - Observational study. Sample Population - Feces and environmental samples from 2 dairy herds. Procedure - Herds were monitored for fecal shedding of S enterica Newport after outbreaks of clinical disease. Fecal and environmental samples were collected approximately monthly from pens housing sick cows and calving cows and from pens containing lactating cows. Cattle shedding the organism were tested serially on subsequent visits to determine carrier status. One farm was resampled after initiation of interventional procedures, including separation of hospital and maternity pens. Isolates were characterized via serotyping, determination of antimicrobial resistance phenotype, detection of the CMY-2 gene, and DNA fingerprinting. Results - The prevalence (32.4% and 33.3% on farms A and B, respectively) of isolating Salmonella from samples from joint hospital-maternity pens was significantly higher than the prevalence in samples from pens housing preparturient cows (0.8%, both farms) and postparturient cows on Farm B (8.8%). Multi-drug-resistant Salmonella Newport was isolated in high numbers from bedding material, feed refusals, lagoon slurry, and milk filters. One cow excreted the organism for 190 days. Interventional procedures yielded significant reductions in the prevalences of isolating the organism from fecal and environmental samples. Most isolates were of the C2 serogroup and were resistant to third-generation cephalosporins. Conclusions and Clinical Relevance - Management practices may be effective at reducing the persistence of MDR Salmonella spp in dairy herds, thus mitigating animal and public health risk.

Material influence on the stress corrosion cracking of rock bolts

Rock bolt stress corrosion cracking (SCC) has been investigated using the linearly increasing stress test (LIST). One series of experiments determined the threshold stress of various bolt metallurgies (900 MPa for 1355AXRC, and 800 MPa for MAC and MA840B steels). The high values of threshold stress suggest that SCC begins in rock bolts when they are sheared by moving rock strata. SCC only occurred for environmental conditions which produce hydrogen on the sample surface, leading to hydrogen embrittlement and SCC. Different threshold potentials were determined for a range of metallurgies. Cold work was shown to increase the resistance of the steel to SCC. Rock bolt rib geometry does not have a direct impact on the SCC resistance properties of the bolt, although the process by which the ribs are produced can introduce tensile stresses into the bolt which lower its resistance to SCC. (C) 2004 Elsevier Ltd. All rights reserved.

High speed versus conventional grinding in high removal rate machining of alumina and alumina-titania

High removal rate (up to 16.6 mm(3)/s per mm) grinding of alumina and alumina-titania was investigated with respect to material removal and basic grinding parameters using a resin-bond 160 mu m grit diamond wheel at the speeds of 40 and 160 m/s, respectively. The results show that the material removal for the single-phase polycrystalline alumina and the two-phase alumina-titania composite revealed identical mechanisms of microfracture and grain dislodgement under the grinding conditioned selected. There were no distinct differences in surface roughness and morphology for both materials ground at either conventional or high speed. An increase in material removal rate did not necessarily worsen the surface toughness for the two materials at both speeds. Also the grinding forces for the two ceramics demonstrated similar characteristics at any grinding speeds and specific removal rates. Both normal and tangential grinding forces and their force ratios at the high speed were lower than those at the conventional speed, regardless of removal rates. An increase in specific removal rate caused more rapid increases in normal and tangential forces obtained at the conventional grinding speed than those at the high speed. Furthermore, it is found that the high speed grinding at all the removal rates exerted a great amount of coolant-induced normal forces in grinding zone, which were 4-6 times higher than the pure normal grinding forces. (c) 2004 Elsevier Ltd. All rights reserved.

High-breakdown linear discriminant analysis

The classification rules of linear discriminant analysis are defined by the true mean vectors and the common covariance matrix of the populations from which the data come. Because these true parameters are generally unknown, they are commonly estimated by the sample mean vector and covariance matrix of the data in a training sample randomly drawn from each population. However, these sample statistics are notoriously susceptible to contamination by outliers, a problem compounded by the fact that the outliers may be invisible to conventional diagnostics. High-breakdown estimation is a procedure designed to remove this cause for concern by producing estimates that are immune to serious distortion by a minority of outliers, regardless of their severity. In this article we motivate and develop a high-breakdown criterion for linear discriminant analysis and give an algorithm for its implementation. The procedure is intended to supplement rather than replace the usual sample-moment methodology of discriminant analysis either by providing indications that the dataset is not seriously affected by outliers (supporting the usual analysis) or by identifying apparently aberrant points and giving resistant estimators that are not affected by them.

A nanometre-scale non-periodic structural variation in high temperature superconducting ceramics and the implications for properties

Non-periodic structural variation has been found in the high T-c cuprates, YBa2Cu3O7-x and Hg0.67Pb0.33Ba2Ca2Cu3O8+delta, by image analysis of high resolution transmission electron microscope (HRTEM) images. We use two methods for analysis of the HRTEM images. The first method is a means for measuring the bending of lattice fringes at twin planes. The second method is a low-pass filter technique which enhances information contained by diffuse-scattered electrons and reveals what appears to be an interference effect between domains of differing lattice parameter in the top and bottom of the thin foil. We believe that these methods of image analysis could be usefully applied to the many thousands of HRTEM images that have been collected by other workers in the high temperature superconductor field. This work provides direct structural evidence for phase separation in high T-c cuprates, and gives support to recent stripes models that have been proposed to explain various angle resolved photoelectron spectroscopy and nuclear magnetic resonance data. We believe that the structural variation is a response to an opening of an electronic solubility gap where holes are not uniformly distributed in the material but are confined to metallic stripes. Optimum doping may occur as a consequence of the diffuse boundaries between stripes which arise from spinodal decomposition. Theoretical ideas about the high T-c cuprates which treat the cuprates as homogeneous may need to be modified in order to take account of this type of structural variation.

Combination therapy with tacrolimus and anti-thymocyte globulin for the treatment of steroid-resistant acute graft-versus-host disease developing during cyclosporine prophylaxis

We report our experience with the combination of anti-thymocyte globulin (ATGAM) and tacrolimus in the treatment of 20 patients with steroid refractory and dependent acute graft-versus-host disease (GVHD) transplanted between August 1996 and February 2000. All patients received cyclosporine-based GVHD prophylaxis. Thirteen patients developed a maximum of grade TV, five grade III and two grade II acute GVHD, with 15 patients being refractory to steroids and five dependent on steroids. Patients were treated with ATGAM (15 mg/kg for 5 d) and tacrolimus (0.025-0.1 mg/kg/d) in addition to continuation of their high-dose steroids and cessation of their cyclosporine. Within 28 d of treatment, we observed eight complete responses (CR), six partial responses (PR) and six with no response. Overall response (CR + PR) was predicted by GVHD severity. Infectious complications occurred in 80% of patients. The median survival was 86.5 d (range, 21-1081 d) with 35% of patients remaining alive, Survival following combination therapy was significantly more likely in men (P < 0.001), skin-only GVHD (P = 0.027), less severe GVHD (P = 0.048), and in responders to tacrolimus and ATGAM (P< 0.001). In conclusion, concurrent introduction of ATGAM and tacrolimus is a promising therapeutic combination for GVHD refractory to steroids and cyclosporine.

Time of treatment influences the appearance of drug-resistant parasites in Plasmodium falciparum infections

A deterministic mathematical model which predicts the probability of developing a new drug-resistant parasite population within the human host is reported, The model incorporates the host's specific antibody response to PfEMP1, and also investigates the influence of chemotherapy on the probability of developing a viable drug-resistant parasite population within the host. Results indicate that early, treatment, and a high antibody threshold coupled with a long lag time between antibody stimulation and activity, are risk factors which increase the likelihood of developing a viable drug-resistant parasite population. High parasite mutation rates and fast PfEMP1 var gene switching are also identified as risk factors. The model output allows the relative importance of the various risk factors as well as the relationships between them to be established, thereby increasing the understanding of the conditions which favour the development of a new drug-resistant parasite population.

Genetic linkage analysis of the lesser grain borer Rhyzopertha dominica identifies two loci that confer high-level resistance to the fumigant phosphine

High levels of inheritable resistance to phosphine in Rhyzopertha dominica have recently, been detected in Australia and hi art effort to isolate the genes responsible For resistance we have used random amplified DNA fingerprinting (RAF) to produce a genetic linkage map of R. dominica. The map consists of 94 dominant DNA markers with art average distance between markers of 4.6 cM and defines nine linkage groups with a total recombination distance of 390.1 cM. We have identified two loci that are responsible for high-level resistance. One provides similar to50x resistance to phosphine while the other provides 12.5x resistance and in combination, the two genes act synergistically to provide a resistance level 250 x greater than that of fully susceptible beetles. The haploid genome size has been determined to be 4.76 x 10(8) bp, resulting in an average physical distance of 1.2 Mbp per map unit. No recombination has been observed between either of the two resistance loci and their adjacent DNA markers in a population of 44 fully resistant F-5 individuals, which indicates that the genes are likely to reside within 0.91 cM (1.1 Mbp) of the DNA markers.

Peanut resistance to Sclerotinia minor and S-sclerotiorum

The fungi Sclerotinia minor and S. sclerotiorum are the causal agents of two similar diseases of peanut (Arachis hypogaea L.). Both diseases cause significant losses in the Australian peanut industry. Development of cultivars with resistance to Sclerotinia will be an important component of integrated control. The aims of this project are to generate information that will assist in breeding for Sclerotinia resistance in peanut: to identify Sclerotinia-resistant peanut germplasm, to understand the inheritance and estimate heritability of resistance, and to test the effectiveness of identified sources of resistance against both S. minor and S. sclerotiorum. This study has clearly established that material that shows resistance to S. minor in the USA is resistant to S. minor and likely to be resistant to S. sclerotiorum in Australia. The high level of resistance to both S. minor and S. sclerotiorum in germplasm from Texas, particularly TxAG-4, was confirmed. VA 93B showed good resistance in the field, which is primarily due to the open bush type rather than physiological resistance. Physiological resistance to S. minor was also identified in a cultivar and a landrace from Indonesia and a rust-resistant line from Queensland. All germplasm found to have high physiological resistance to S. minor belonged to the Spanish type. Inheritance of physiological resistance to S. minor was studied using a Generation Means Analysis (GMA) of the cross TxAG-4/VA 93B and its reciprocal. The broad-sense heritability of physiological resistance on a single plant basis was estimated at 47%, much higher than earlier estimates obtained in field studies. The average gene action of Sclerotinia resistance genes from TxAG-4 was found to be additive. No dominance effects were detected in the GMA. A small but significant reciprocal effect between TxAG-4 and VA 93B indicated that VA 93B passed on some physiological resistance maternally. An experiment was conducted to confirm the value of resistance against both S. minor and S. sclerotiorum. TxAG-4 was found to have physiological resistance to both S. minor and S. sclerotiorum. This resistance was expressed against both Sclerotinia species by progeny that were selected for resistance to S. minor. On the basis of the information obtained, the comparative advantages of 3 strategies for Sclerotinia-resistant cultivar development are discussed: (1) introduction of germplasm; (2) recurrent backcrossing with screening and crossing in the BCnF1 generation; and (3) pedigree selection. At present, introduction and backcrossing are recommended as the preferred strategies.

Manipulation of colonic bacteria and volatile fatty acid production by dietary high amylose maize (amylomaize) starch granules

Aims : To study the effects of amylomaize starch and modified (carboxymethylated and acetylated) amylomaize starches on the composition of colonic bacteria and the production of volatile fatty acids, in mice. Methods and Results : Balb/c mice were fed with experimental diets containing various amount of amylomaize and modified amylomaize starches. Colonic bacterial populations and short-chain fatty acids were monitored. Results showed that the increases in indigenous bifidobacteria were detected in mice fed all starches tested; however, the highest numbers were observed in the group fed with 40% unmodified amylomaize starch. The starch type influenced the populations of indigenous Lactobacillus , Bacteroides and coliforms. High Lactobacillus numbers were achieved in the colon of mice fed with high concentration of amylomaize starch. Acetylated amylomaize starch significantly reduced the population of coliforms. In addition, orally dosed amylomaize utilizing bifidobacteria reached their highest levels when fed together with amylomaize or carboxymethylated amylomaize starch and in both cases butyrate levels were markedly increased. Conclusions: These results indicate that different amylomaize starches could generate desirable variation in gut microflora and that particular starches may be used to selectively modify gut function. Significance and Impact of Study: Amylomaize starch appeared to enhance the desirable composition of colonic bacteria in mice, and suggested it possessed the potential prebiotic properties.MTherefore, resistant starch and its chemical derivatives may exert beneficial impacts to the human colon.

Resistance development in community-acquired strains of methicillin-resistant Staphylococcus aureus: an in vitro study

This study compares in vitro antimicrobial resistance development between strains of Staphylococcus aureus including newly described community-acquired methicillin-resistant strains (CA-MRSA). High-level resistance developed in all strains of S. aureus after exposure to rifampicin and gentamicin and in some strains after fusidic acid exposure, independent of methicillin resistance phenotype. Resistance did not develop after exposure to clindamycin, cotrimoxazole, ciprofloxacin, linezolid, or vancomycin. These results have important implications for therapy of CA-MRSA infections. (C) 2004 Elsevier B.V. and the International Society of Chemotherapy. All rights reserved.

mecA locus diversity in methicillin-resistant Staphylococcus aureus isolates in Brisbane, Australia, and the development of a novel diagnostic procedure for the Western Samoan phage pattern clone

An emerging public health phenomenon is the increasing incidence of methicillin-resistant Staphylococcus aureus (MRSA) infections that are acquired outside of health care facilities. One lineage of community-acquired MRSA (CA-MRSA) is known as the Western Samoan phage pattern (WSPP) clone. The central aim of this study was to develop an efficient genotyping procedure for the identification of WSPP isolates. The approach taken was to make use of the highly variable region downstream of mecA in combination with a single nucleotide polymorphism (SNP) defined by the S. aureus multilocus sequence typing (MLST) database. The premise was that a combinatorial genotyping method that interrogated both a highly variable region and the genomic backbone would deliver a high degree of informative power relative to the number of genetic polymorphisms-interrogated. Thirty-five MRSA isolates were used for this study, and their gene contents and order downstream of mecA were determined. The CA-MRSA isolates were found to contain a truncated mecA downstream region consisting of mecA-HVR-IS431 mec-dcs-Ins117, and a PCR-based method for identifying this structure was developed. The hospital-acquired isolates were found to contain eight different mecA downstream regions, three of which were novel. The Minimum SNPs computer software program was used to mine the S. aureus MLST database, and the arcC 2726 polymorph was identified as 82% discriminatory for ST-30. A real-time PCR assay was developed to interrogate this SNP. We found that the assay for the truncated mecA downstream region in combination with the interrogation of arcC position 272 provided an unambiguous identification of WSPP isolates.

Macrophages overexpressing tartrate-resistant acid phosphatase show altered profile of free radical production and enhanced capacity of bacterial killing

Activated macrophages and osteoclasts express high amounts of tartrate-resistant acid phosphatase (TRACP, acp5). TRACP has a binuclear iron center with a redox-active iron that has been shown to catalyze the formation of reactive oxygen species (ROS) by Fenton's reaction. Previous Studies Suggest that ROS generated by TRACP may participate in degradation of endocytosed bone matrix products in resorbing osteoclasts and degradation of foreign Compounds during. antigen presentation in activated macrophages. Here we have compared free radical production in macrophages of TRACP overexpressing (TRACP +) and wild-type (WT) mice. TRACP overexpression increased both ROS levels and Superoxide production. Nitric oxide production was increased in activated macrophages or WT mice, but not in TRACP+ mice, Macrophages from TRACP+ mice showed increased capacity or bacterial killing. Recombinant TRACP enzyme was capable of bacterial killing in the presence of hydrogen peroxide. These results suggest that TRACP has an important biological function in immune defense systern.