Synthesis and electrochemical properties of mesoporous nickel oxide

Mesoporous Ni(OH)(2) is synthesized using sodium dodecyl sulfate as a template and urea as a hydrolysis-controlling agent. Mesoporous NiO with a centralized pore-size distribution is obtained by calcining Ni(OH)(2) at different temperatures. The BET specific surface area reaches 477.7 m(2) g(-1) for NiO calcined at 250 degreesC. Structure characterizations indicate a good mesoporous structure for the nickel oxide samples. Cyclic voltammetry shows the NiO to have good capacitive behaviour due to its unique mesoporous structure when using a large amount of NiO to fabricate the electrode. Compared with NiO prepared by dip-coating and cathodic precipitation methods, mesoporous NiO with a controlled pore structure can be used in much larger amounts to fabricate electrodes and still maintain a high specific capacitance and good capacitive behaviour. (C) 2004 Elsevier B.V. All rights reserved.

Synthesis and characterization of mesoporous nickel oxide and its application to electrochemical capacitor

Mesoporous Ni(OH)(2) was synthesized using cationic surfactant as template and urea as hydrolysis-controlling agent. Mesoporous NiO with centralized pore size distribution was obtained by calcining Ni(OH)(2) at different temperatures. The BET specific surface area reaches 477.7 m(2).g(-1) for NiO calcined at 523 K. Structure characterizations indicate the polycrystalline pore wall of mesoporous nickel oxide. The pore-formation mechanism is also deduced to be quasi-reverse micelle mechanism. Cyclic voltammetry shows the good capacitive behavior of these NiO samples due to its unique mesoporous structure when using large amount of NiO to fabricate electrode. Compared with NiO prepared by dip-coating and cathodic precipitation methods, this mesoporous NiO with controlled pore structure can be used in much larger amount to fabricate the electrode and still maintains high specific capacitance and good capacitive behavior.

Silica membrane reactors for hydrogen production from water gas shift

This paper presents an analysis of membrane reactor (MR) operation and design for enhanced hydrogen production from the water gas shift (WGS) reaction. It has been established that membrane reactors can enhance an equilibrium limited reaction through product separation. However, the detailed effects of reactor setup, membrane configuration and catalyst volume have yet to be properly analysed for this reaction. This paper investigates new ideas for membrane reactors such as the development of new catalytic films, for improved interaction between the reaction and separation zones. Current membrane reactors utilise a packed bed of catalyst within the membrane tube, utilising a large volume of catalyst to drive reaction. This is still inefficient and provides only limited benefits over conventional WGS reactors. New reactor configurations look to optimise the interactive effects between reaction and separation to provide improved operation. In this paper, thin film catalysts were produced using dip coating and spray coating techniques. This technique produced catalyst coatings with good thickness, though the abrasion strength of the dip coated catalyst was quite low. The catalyst was tested in a packed bed reactor for temperature activity at low temperatures and catalyst activity at varying levels of excess water

Thermal characterization of polyester-melamine coating matrices prepared under nonisothermal conditions

Thermal analysis methods (differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical thermal analysis) were used to characterize the nature of polyester-melamine coating matrices prepared under nonisothermal, high-temperature, rapid-cure conditions. The results were interpreted in terms of the formation of two interpenetrating networks with different glass-transition temperatures (a cocondensed polyester-melamine network and a self-condensed melamine-melamine network), a phenomenon not generally seen in chemically similar, isothermally cured matrices. The self-condensed network manifested at high melamine levels, but the relative concentrations of the two networks were critically dependent on the cure conditions. The optimal cure (defined in terms of the attainment of a peak metal temperature) was achieved at different oven temperatures and different oven dwell times, and so the actual energy absorbed varied over a wide range. Careful control of the energy absorption, by the selection of appropriate cure conditions, controlled the relative concentrations of the two networks and, therefore, the flexibility and hardness of the resultant coatings. (C) 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Cbem 41: 1603-1621, 2003.

The influence of coating materials on some properties of alginate beads and survivability of microencapsulated probiotic bacteria

The probiotics, Lactobacillus acidophilus 547, Bifidobacterium bifidum ATCC 1994, and Lactobacillus casei 01, were encapsulated into uncoated calcium alginate beads and the same beads were coated with three types of material, chitosan, sodium alginate, and poly-L-lysine in combination with alginate. The thickness of the alginate beads increased with the addition of coating materials. No differences were detectable in the bead strength by texture analysis or in the thickness of the beads with different types of coating materials by transmission electron microscopy. The survivability of three probiotics in uncoated beads, coated beads, and as free cells (unencapsulated) was conducted in 0.6% bile salt solution and simulated gastric juice (pH 1.55) followed by incubation in simulated intestinal juice with and without 0.6% bile salt. Chitosan-coated alginate beads provided the best protection for L. acidophilus and L. casei in all treatments. However, B. bifidum did not survive the acidic conditions of gastric juice even when encapsulated in coated heads. (C) 2004 Elsevier Ltd. All rights reserved.

Improved corrosion resistance of AZ91D magnesium alloy by an aluminium-alloyed coating

An aluminum-alloyed coating was applied onto the surface of magnesium alloy AZ91D. The coating formed in aluminium powder at 420 degrees C is rich in the beta (Mg17Al12) phase. Polarisation curve, AC impedance, salt immersion and salt spray were carried out to investigate the corrosion behaviour and assess the corrosion performance of the coated magnesium alloy. It was found that a coated AZ91D specimen was much more corrosion resistant and harder than an uncoated one. The improved corrosion resistance was mainly ascribed to the high volume fraction of beta phase in the coating. (c) 2004 Elsevier B.V. All rights reserved.

A study of the effects of postcure treatments on polyester-melamine coating matrices

The effect of postcure high energy (gamma), ultraviolet (UV) and thermal treatment on the properties of polyester-melamine clearcoats of a range of compositions has been investigated. Two initial cure conditions were used, of which one was '' optimally '' cured and the other undercured. It was found that postcure treatments, particularly gamma and UV, led to coatings of similar mechanical and thermal properties irrespective of initial cure, although the change in properties on postcure treatment was greater for the under-cured samples. The results were interpreted in terms of the effect of the treatments on the structure of the crosslinked matrices. The study suggests the possibility of the development of a dual-cure process for polyester-melamines, whereby cure optimization and property improvement can be achieved. This could also be used to '' correct '' for small variations in thermal cure levels brought about by adventitious online fluctuations in cure oven conditions.

The diagnostic interview for psychoses (DIP): development, reliability and applications

Background. We describe the development, reliability and applications of the Diagnostic Interview for Psychoses (DIP), a comprehensive interview schedule for psychotic disorders. Method. The DIP is intended for use by interviewers with a clinical background and was designed to occupy the middle ground between fully structured, lay-administered schedules, and semi-structured., psychiatrist-administered interviews. It encompasses four main domains: (a) demographic data; (b) social functioning and disability; (c) a diagnostic module comprising symptoms, signs and past history ratings; and (d) patterns of service utilization Lind patient-perceived need for services. It generates diagnoses according to several sets of criteria using the OPCRIT computerized diagnostic algorithm and can be administered either on-screen or in a hard-copy format. Results. The DIP proved easy to use and was well accepted in the field. For the diagnostic module, inter-rater reliability was assessed on 20 cases rated by 24 clinicians: good reliability was demonstrated for both ICD-10 and DSM-III-R diagnoses. Seven cases were interviewed 2-11 weeks apart to determine test-retest reliability, with pairwise agreement of 0.8-1.0 for most items. Diagnostic validity was assessed in 10 cases, interviewed with the DIP and using the SCAN as 'gold standard': in nine cases clinical diagnoses were in agreement. Conclusions. The DIP is suitable for use in large-scale epidemiological studies of psychotic disorders. as well as in smaller Studies where time is at a premium. While the diagnostic module stands on its own, the full DIP schedule, covering demography, social functioning and service utilization makes it a versatile multi-purpose tool.

Postharvest characteristics and handling of litchi fruit - an overview

Litchi ( Litchi chinensis Sonn.) is a tropical to subtropical crop that originated in South-East Asia. Litchi fruit are prized on the world market for their flavour, semi-translucent white aril and attractive red skin. Litchi is now grown commercially in many countries and production in Australia, China, Israel, South Africa and Thailand has expanded markedly in recent years. Increased production has made significant contributions to economic development in these countries, especially those in South-East Asia. Non-climacteric litchi fruit are harvested at their visual and organoleptic optimum. They are highly perishable and, consequently, have a short life that limits marketability and potential expansion of demand. Pericarp browning and pathological decay are common and important defects of harvested litchi fruit. Postharvest technologies have been developed to reduce these defects. These technologies involve cooling and heating the fruit, use of various packages and packaging materials and the application of fungicides and other chemicals. Through the use of fungicides and refrigeration, litchi fruit have a storage life of about 30 days. However, when they are removed from storage, their shelf life at ambient temperature is very short due to pericarp browning and fruit rotting. Low temperature acclimation or use of chitsoan as a coating can extend the shelf life. Sulfur dioxide fumigation effectively reduces pericarp browning, but approval from Europe, Australia and Japan for this chemical is likely to be withdrawn due to concerns over sulfur residues in fumigated fruit. Thus, sulfur-free postharvest treatments that maintain fruit skin colour are increasingly important. Alternatives to SO2 fumigation for control of pericarp browning and fruit rotting are pre-storage pathogen management, anoxia treatment, and dipping in 2% hydrogen chloride solution for 6-8 min following storage at 0 degrees C. Insect disinfestation has become increasingly important for the expansion of export markets because of quarantine issues associated with some fruit fly species. Thus, effective disinfestation protocols need to be developed. Heat treatment has shown promise as a quarantine technology, but it injures pericarp tissue and results in skin browning. However, heat treatment can be combined with an acid dip treatment that inhibits browning. Therefore, the primary aim of postharvest litchi research remains the achievement of highly coloured fruit which is free of pests and disease. Future research should focus on disease control before harvest, combined acid and heat treatments after harvest and careful temperature management during storage and transport.