Outbound Travel Depends on Business Returns: Australian Evidence

In an earlier note, Collins and Tisdell (2002b) explored the possibility of a long-run relationship between Australian business returns and international business travel. Using annual data they found that such a relationship exists. The purpose of this study is to further examine this relationship using quarterly data for the time frame 1974:1 to 1999:4. In addition, previous studies on international business travel have offered some but not strong evidence for the existence of a positive relationship between the level of international business travel and real GDP of the origin country. This study suggests that the aggregate return on business investments is a better predictor of international business travel than GDP. The Engle-Granger and Johansen's maximum-likelihood cointegration procedures are used to show a long-term relationship exists between Australian outbound business travel and Australian business returns, but not with Real Australian GDP. Reasons for this relationship are discussed.

An analysis of the relationship between grain size, solute content, and the potency and number density of nucleant particles

To be able to determine the grain size obtained from the addition of a grain refining master alloy, the relationship between grain size (d), solute content (defined by the growth restriction factor Q), and the potency and number density of nucleant particles needs to be understood. A study was undertaken on aluminium alloys where additions of TiB2 and Ti were made to eight wrought aluminum alloys covering a range of alloying elements and compositions. It was found from analysis of the data that d = a/(3)root pct TiB2 + b/Q. From consideration of the experimental data and from further analysis of previously published data, it is shown that the coefficients a and b relate to characteristics of the nucleant particles added by a grain refiner. The term a is related to the maximum density of active TiB2 nucleant particles within the melt, while b is related to their potency. By using the analysis methodology presented in this article, the performance characteristics of different master alloys were defined and the effects of Zr and Si on the poisoning of grain refinement were illustrated.

Long-term flow rates and biomat zone hydrology in soil columns receiving septic tank effluent

Soil absorption systems (SAS) are used commonly to treat and disperse septic tank effluent (STE). SAS can hydraulically fail as a result of the low permeable biomat zone that develops on the infiltrative surface. The objectives of this experiment were to compare the hydraulic properties of biomats grown in soils of different textures, to investigate the long-term acceptance rates (LTAR) from prolonged application of STE, and to assess if soils were of major importance in determining LTAR. The STE was applied to repacked sand, Oxisol and Vertisol soil columns over a period of 16 months, at equivalent hydraulic loading rates of 50, 35 and 8 L/m(2)/d, respectively Infiltration rates, soil matric potentials, and biomat hydraulic properties were measured either directly from the soil columns or calculated using established soil physics theory. Biomats 1 to 2 cm thick developed in all soils columns with hydraulic resistances of 27 to 39 d. These biomats reduced a 4 order of magnitude variation in saturated hydraulic conductivity (K.) between the soils to a one order of magnitude variation in LTAR. A relationship between biomat resistance and organic loading rate was observed in all soils. Saturated hydraulic conductivity influenced the rate and extent of biomat development. However, once the biomat was established, the LTAR was governed by the resistance of the biomat and the sub-biomat soil unsaturated flow regime induced by the biomat. Results show that whilst initial soil K. is likely to be important in the establishment of the biomat zone in a trench, LTAR is determined by the biomat resistance and the unsaturated soil hydraulic conductivity, not the K, of a soil. The results call into question the commonly used approach of basing the LTAR, and ultimately trench length in SAS, on the initial K, of soils. (c) 2006 Elsevier Ltd. All rights reserved.

Relative predictive value of intraventricular dysynchrony in determining long-term outcome in patients with known or suspected coronary disease

Improvement of intra-ventricular dysynchrony (IVD) in pts undergoing bi-ventricular pacing is associated with clinical improvementbut little isknownabout the relationship between IVD and prognosis.We sought whether IVD influences long-term outcome in pts with known or suspected coronary disease (CAD). Tissue Doppler imaging was performed in 184 pts (aged 61±10 years, 67% male) prior to dobutamine echo. From velocity curves the interval between QRS onset and max systolic velocity (Ts) was measured in basal septal, lateral, inferior and anterior segments. The maximal difference in Ts between segments (TsMax) was used as a measure of IVD. The standard deviation (TsSD) between all segments and the septal-lateral difference (TsSL) were also calculated. Pts were followed up for a median interval of 5 years and a Cox model used for survival analysis. The medianwall motion index (WMI) was 1.3 (IQR 1.0–1.8) at rest and 1.4 (IQR 1.3–1.9) at stress. The table shows IVD parameters. Forty-one deaths occurred during follow-up. Pts who died during follow-up, compared to survivors, showed greater IVD. WMI at rest (p = 0.03) and peak stress (p = 0.02), TsSD (p = 0.06), TsSL (p = 0.02) and TsMax (p = 0.05) but not QRS width were univariate predictors of mortality. TsSL was the only independent predictor of death (p = 0.01). Therefore, IVD is common in pts with known or suspected CAD. Pts with more IVD have reduced long-term survival, independent of WMI.