Hall-Petch parameters for tension and compression in cast Mg

The flow stress in tensile and compressive deformation has been determined in cast Mg, for a wide range of grain sizes between 36 mum and 1.5 mm. The grain size was varied by alloying Mg with small amounts of Zr. It was found that the 0.2% offset flow stress, sigma(y) (MPa), varies with the grain size, d (m), as sigma(y) = 17.7 + 0.25 d(-1/2) in tension, while sigma(y) = -2.3 + 0.39 d(-1/2) in compression. Possible reasons for the difference between tension and compression are discussed.

Quantitative trends in airborne loads of Celtis sinensis pollen and associations with meteorological variables in a subtropical Australian environment

Celtis sinensis is an introduced plant species to the southeastern region of Queensland that has had a destructive affect on indigenous plant Communities and its pollen has been identified as an allergen Source. Pollen belonging to C. sinensis was sampled during a 5-year (June 1994-May 1999) atmospheric pollen-monitoring programme in Brisbane, Australia, using a Burkard 7-day spore trap. The seasonal incidence of airborne C. sinensis pollen (CsP) in Brisbane occurred over a brief period each year during spring (August-September), while peak concentrations were restricted to the beginning of September. individual CsP seasons were heterogeneous with daily counts within the range 1-10 grains m(-3) on no more than 60 sampling days; however, smaller airborne concentrations of CsP were recorded out of each season. Correlation co-efficients were significant each year for temperature (p0.05) and relative humidity (p>0.05). A significant relationship (r(2)=0.81, p=0.036) was established between the total CsP count and pre-seasonal average maximum temperature; however, periods of precipitation (>2mm) were demonstrated to significantly lower the daily concentrations of CsP from the atmosphere. Given the environmental and clinical significance of CsP and its prevalence in the atmosphere of Brisbane, a Clinical population-based Study is required to further understand the pollen's importance as a seasonal sensitizing source in this region.

Hall-Petch parameters in tension and compression in cast Mg-2Zn alloys

The flow stress in tension and compression has been measured as a function of plastic strain in Mg-2Zn castings with grain sizes ranging from 55 to 340 mum. Hall-Petch parameters have been calculated and are compared to those previously reported. In contrast to the behaviour of pure Mg grain refined with Zr and of hot-worked and recrystallised pure Mg and Mg-Zn alloys, the cast material shows little tension/compression asymmetry of the flow stress. The possible effects of texture and of twinning are noted. (C) 2004 Elsevier B.V. All rights reserved.

Dynamic interfacial tension of aqueous solutions of PVAAs and its role in liquid-liquid dispersion stabilization

In liquid-liquid dispersion systems, the dynamic change of the interfacial properties between the two immiscible liquids plays an important role in both the emulsification process and emulsion stabilization. In this paper, experimentally measured dynamic interfacial tensions of 1-chlorobutane in the aqueous solutions of various random copolymers of polyvinyl acetate and polyvinyl alcohol (PVAA) are presented. Theoretical analyses on these results suggest that the adsorption of the polymer molecules is controlled neither by the bulk diffusion process nor the activation energy barrier for the adsorption but the conformation of polymer molecules. Based on the concept of critical concentration of condensation for polymer adsorption, as well as the observation that the rate at which the dynamic interfacial tension changes does not correlate to the PVAA's ability to stabilize a single drop, it is postulated that the main stabilization mechanism for the PVAAs is by steric hindrance, not the Gibbs-Marangoni effect offered by the small molecule surfactants.

A randomized, controlled trial to determine the efficacy of paper tape in preventing hypertrophic scar formation in surgical incisions that traverse Langer's skin tension lines

Background: How a scar is managed postoperatively influences Its cosmetic outcome. After Suture removal, scars are susceptible to skin tension, which may be the trigger for hypertrophic scarring. Paper tape to support the scar may reduce multidirectional forces and prevent hypertrophic scarring. Methods: Seventy patients who had under gone cesarean section at the Royal Brisbane and Women's Hospital were randomized to treatment and control groups. Patients in the control group received no postoperative intervention. Patients in the treatment group applied paper tape to their scars for 12 weeks. Scars were assessed at 6 weeks, 12 weeks, and 6 months after surgery using Ultrasound to measure intradermal scar volume. Scars were also assessed using the International Clinical Recommendations. Results: Paper tape significantly decreased scar volume by a mean of 0.16 cm(3), (95 percent confidence Interval, 0.00 to 0.29 cm(3)) At 12 weeks after surgery, 41 percent of the control group developed hypertrophic scars compared with none in the treatment group (exact test, p = 0.003). In the treatment group, one patient developed a hypertrophic scar and four developed stretched scars only after the tape was removed. The odds of developing a hypertrophic scar were 13.6 times greater in the control than in the treatment group (95 percent confidence interval, 3.6 to 66.9). Of the 70 patients randomized, 39 completed the study. Four patients in the treatment group developed a localized red rash beneath the tape. These reactions were minor and transient and resolved without medical intervention. Conclusions: The development of hypertrophic and stretched scars in the treatment group only after the tape was removed suggests that tension acting on a scar is die trigger for hypertrophic scarring. Paper tape is likely to be an effective modality for the prevention of hypertrophic scarring through its ability to eliminate scar tension.

Particle bed charge decay behaviour under high tension roll separation

A new theory of particle discharge in high tension roll (HTR) separation is presented. The discharge dynamics of an isolated charged particle resting on a conducting surface are studied first. The analysis is extended to particle discharge in a homogenous particle bed. Finally, the paper looks at the more realistic scenario of particle discharge in a non-homogenous particle bed. The consequences of the resulting theory on HTR separation are discussed. Predictions from the new theory are tested against experimental HTR separations at the pilot scale. (c) 2005 Elsevier Ltd. All rights reserved.

Client fish ectoparasite loads and cleaner shrimp Urocaridella sp c hunger levels affect cleaning behaviour

Cleaning is a classic example of mutualism and determining the factors that maintain the balance between the costs and benefits for mutualist partners can assist our understanding of how cleaning relationships are maintained. Optimal foraging theory suggests two factors that might help to maintain the relationship between cleaners and their clients: client ectoparasite load and cleaner hunger levels. The ecological relevance and importance of foraging by cleaner fish in marine systems has been demonstrated repeatedly, yet there is little information available on this behaviour in cleaner shrimp. To determine whether cleaner shrimp base their choice of client fish on food patch quality (i.e. client fish ectoparasite load) we offered the yellow-beaked cleaner shrimp Urocaridella sp. c a choice of parasitized and unparasitized rock cods, Cephalopholis cyanostigma. To determine whether cleaner shrimp hunger levels influence cleaning time, we manipulated hunger levels in Urocaridella sp. c and examined their behaviour towards parasitized client fish. Cleaner shrimp preferred parasitized to unparasitized client fish and food-deprived cleaner shrimp cleaned parasitized rock cods more frequently than satiated cleaner shrimp did. Therefore, variations in client fish ectoparasite load and cleaner shrimp hunger level are two factors that affect the balance in this mutualism. Finally, our results meet some of the assumptions of biological market theory, a framework used to understand cooperative interactions, and thus this framework is suggested for future studies on this cleaning system.

Effects of tensioning the lumbar fasciae on segmental stiffness during flexion and extension - Young investigator award winner

Study Design. Biomechanical study of unembalmed human lumbar segments. Objective. To investigate the effects of tensioning the lumbar fasciae ( transversus abdominis [TrA]) aponeurosis) on segment stiffness during flexion and extension. Summary of Background Data. Animal and human studies suggest that TrA may influence intersegmental movement via tension in the middle and posterior layers of lumbar fasciae ( MLF, PLF). Methods. Compressive flexion and extension moments were applied to 17 lumbar segments from 9 unembalmed cadavers with 20 N lateral tension of the TrA aponeurosis during: 1) static tests: load was compared when fascial tension was applied during static compressive loads into flexion-extension; 2) cyclic loading tests: load, axial displacement, and stiffness were compared during repeated compressive loading cycles into flexion-extension. After testing, the PLF was incised to determine the tension transmitted by each layer. Results. At all segments and loads (< 200 N), fascial tension increased resistance to flexion loads by similar to 9.5 N. In 15 of 17, fascial tension decreased resistance to extension by similar to 6.6 N. Fascial tension during cyclic flexion loading decreased axial displacement by 26% at the onset of loading (0 - 2 N) and 2% at 450 N ( 13 of 17). During extension loading, fascial tension increased displacement at the onset of loading ( 10 of 17) by similar to 23% and slightly (1%) decreased displacement at 450 N. Segment stiffness was increased by 6 N/mm in flexion (44% at 25 N) and decreased by 2 N/mm (8% at 25 N) in extension. More than 85% of tension was transmitted through the MLF. Conclusions. Tension on the lumbar fasciae simulating moderate contraction of TrA affects segmental stiffness, particularly toward the neutral zone.

Involuntary glottal closure during inspiration in muscle tension dysphonia

Objective/Hypothesis: The purpose of this study was to examine respiratory function in a group of patients with muscle tension dysphonia (MTD) Design: Cross-sectional analytical study. Methods: Participants included 15 people with a diagnosis of MTD referred to speech pathology for management of their voice disorder, fiberoptic evidence of glottal or supraglottic constriction during phonation with or without posterior chink, or bowing combined and deviation in perceptual voice quality. A second group of 15 participants with no history of voice disorder served as healthy controls,. Baseline pulmonary function test measures included forced expiratory volume in the first second (FEV1), FVC, FEF25 to 75, FIF50, FEV1/FVC, ratio and FEF50/FIF50 ratio. Hypertonic saline challenge test measures included FEV1 and FIF50 after provocation, close response slope, and provocation dose. Results: Compared with healthy controls, participants with MTD demonstrated a higher prevalence of glottal constriction during inspiration after provocation with nebulized hypertonic saline as demonstrated by a reduction in FIF50 after the hypertonic saline challenge. There was no significant difference between the MTD and healthy control groups in baseline pulmonary function testing. Participants with MTD demonstrated a higher prevalence than healthy controls of abnormal glottic closure during inspiration similar to paradoxical vocal fold movement (PVFM). This suggests that they either had previously undiagnosed coexisting PVFM or that the condition of MTD could be expanded to include descriptions of aberrant glottic function during respiration. This study enhances the understanding of PVFM and MTD by combining research advances made in the fields of otolaryngology and respiratory medicine.

The effects of varying time under tension and volume load on acute neuromuscular responses

The purpose of this study was to examine the effects of different methods of measuring training volume, controlled in different ways, on selected variables that reflect acute neuromuscular responses. Eighteen resistance-trained males performed three fatiguing protocols of dynamic constant external resistance exercise, involving elbow flexors, that manipulated either time-under-tension (TUT) or volume load (VL), defined as the product of training load and repetitions. Protocol A provided a standard for TUT and VL. Protocol B involved the same VL as Protocol A but only 40% concentric TUT; Protocol C was equated to Protocol A for TUT but only involved 50% VL. Fatigue was assessed by changes in maximum voluntary isometric contraction (MVIC), interpolated doublet (ID), muscle twitch characteristics (peak twitch, time to peak twitch, 0.5 relaxation time, and mean rates of force development and twitch relaxation). All protocols produced significant changes (P

Dynamic training volume: A construct of both time under tension and volume load

The purpose of this study was to investigate the effects of three different weight training protocols, that varied in the way training volume was measured, on acute muscular fatigue. Ten resistance-trained males performed all three protocols which involved dynamic constant resistance exercise of the elbow flexors. Protocol A provided a standard for the time the muscle group was under tension (TUT) and volume load (VL), expressed as the product of the total number of repetitions and the load that was lifted. Protocol B involved 40% of the TUT but the same VL compared to protocol A; protocol C was equated with protocol A for TUT but only involved 50% of the VL. Fatigue was assessed by changes in maximum voluntary isometric force and integrated electromyography (iEMG) between the pre- and post-training protocols. The results of the study showed that, when equated for VL, greater TUT produced greater overall muscular fatigue ( p

Fibre slippage in cyclically perturbed fibrous assemblies

The dynamics of fibre slippage within general non-bonded fibrous assemblies is studied in the situation where the assembly is subjected to general small cyclic loads. Two models are proposed. The first is applicable when the general cyclic loading is complemented by an occasional tugging force on one end of a fibre, which causes it to gradually withdraw from the assembly, such as might occur during the pilling of a textile. The second considers the situation in which the cyclic perturbations act around a constant background load applied to the assembly. The dynamics is reminiscent of self-organized critical behaviour. This model is applied to predict the progressive elongation of a single yarn during weaving.

In vivo demonstration of load-induced fluid flow in the rat tibia and its potential implications for processes associated with functional adaptation

Load-induced extravascular fluid flow has been postulated to play a role in mechanotransduction of physiological loads at the cellular level. Furthermore, the displaced fluid serves as a carrier for metabolites, nutrients, mineral precursors and osteotropic agents important for cellular activity. We hypothesise that load-induced fluid flow enhances the transport of these key substances, thus helping to regulate cellular activity associated with processes of functional adaptation and remodelling. To test this hypothesis, molecular tracer methods developed previously by our group were applied in vivo to observe and quantify the effects of load-induced fluid flow under four-point-bending loads. Preterminal tracer transport studies were carried out on 24 skeletally mature Sprague Dawley rats. Mechanical loading enhanced the transport of both small- and larger-molecular-mass tracers within the bony tissue of the tibial mid-diaphysis. Mechanical loading showed a highly significant effect on the number of periosteocytic spaces exhibiting tracer within the cross section of each bone. For all loading rates studied, the concentration of Procion Red tracer was consistently higher in the tibia subjected to pure bending loads than in the unloaded, contralateral tibia, Furthermore, the enhancement of transport was highly site-specific. In bones subjected to pure bending loads, a greater number of periosteocytic spaces exhibited the presence of tracer in the tension band of the cross section than in the compression band; this may reflect the higher strains induced in the tension band compared with the compression band within the mid-diaphysis of the rat tibia. Regardless of loading mode, the mean difference between the loaded side and the unloaded contralateral control side decreased with increasing loading frequency. Whether this reflects the length of exposure to the tracer or specific frequency effects cannot be determined by this set of experiments. These in vivo experimental results corroborate those of previous ex vivo and in vitro studies, Strain-related differences in tracer distribution provide support for the hypothesis that load-induced fluid flow plays a regulatory role in processes associated with functional adaptation.

Extent and economic effect of heat loads on dairy cattle production in Australia

Objective To investigate the extent of heat load problems, caused by the combination of excessive temperature and humidity, in Holstein-Friesian cows in Australia. Also, to outline how milk production losses and consequent costs from this can be estimated and minimised. Procedures Long-term meteorological data for Australia were analysed to determine the distribution of hot conditions over space and time. Fifteen dairy production regions were identified for higher-resolution data analysis. Both the raw meteorological data and their integration into a temperature-humidity thermal index were compiled onto a computer program. This mapping software displays the distribution of climatic patterns, both Australia-wide and within the selected dairying regions. Graphical displays of the variation in historical records for 200 locations in the 15 dairying regions are also available. As a separate study, production data from research stations, on-farm trials and milk factory records were statistically analysed and correlated with the climatic indices, to estimate production losses due to hot conditions. Results Both milk yields and milk constituents declined with increases in the temperature-humidity index. The onset and rate of this decline are dependent on a number of factors, including location, level of production, adaptation, and management regime. These results have been integrated into a farm-level economic analysis for managers of dairy properties. Conclusion By considering the historical patterns of hot conditions over time and space, along with expected production losses, managers of dairy farms can now conduct an economic evaluation of investment strategies to alleviate heat loads. These strategies include the provision of sprinklers, shade structures, or combinations of these.