Deciding who has the right to vote: A comparative analysis of election laws

The paper analyses seven potential restrictions to the right to vote in 63 democracies. Only two of these restrictions have given rise to a near consensus. An overwhelming majority of democracies have decided that the minimum voting age should be 18 and that the right to vote of mentally deficient people should be restricted. There is little consensus about whether the right to vote should be restrcited to citizens, about whether there should be country or electoral district residence requirements, about which electors residing abroad (if any) should retain their right to vote and about which prison inmates (if any) should have the right to vote. The paper also examines two factors that affect right to vote laws: British colonialism and level of political rights. The pattern found with respect to electoral systems, whereby former British colonies emulate their former ruler, is less systematic in the case of right to vote legislation. Finally, “strong” democracies are slightly more inclusive than “weak” ones when deciding who has the right to vote.

Preliminary experience of allied health assessments delivered face to face and by videoconference to a residential facility for elderly people

We investigated whether allied health assessments carried out via videoconferencing were comparable to assessments carried out face to face. Five allied health therapists (in dietetics, occupational therapy, physiotherapy, podiatry and speech pathology) conducted an assessment of 12 high-dependency residents both face to face and by videoconferencing. On a five-point Likert scale, the therapists' mean ratings for the efficiency and suitability of videoconferencing for assessment were significantly lower than for face to face. Their mean rating for the adequacy of their care plans was also significantly lower for videoconferencing than for face to face. However, in each case the dietician's assessments did not differ significantly between the two modalities. In 35 cases out of 60, two independent raters agreed that the therapists' care plans after the videoconferencing and face-to-face assessments were the same. However, the level of agreement between raters was only moderate (kappa=0.31). Despite the therapists' (natural) preference for face-to-face working, care plans formulated via videoconferencing were reasonably similar to those formulated in face-to-face assessment. Allied health assessments carried out by videoconferencing would therefore seem to be feasible.

The effect of channel geometry and wall boundary conditions on the formation of extrusion surface instabilities for LLDPE

It is believed that surface instabilities can occur during the extrusion of linear low density polyethylene due to high extensional stresses at the exit of the die. Local crack development can occur at a critical stress level when melt rupture is reached. This high extensional stress results from the rearrangement of the flow at the boundary transition between the wall exit and the free surface. The stress is highest at the extrudate surface and decreases into the bulk of the material. The location of the region where the critical level is reached can determine the amplitude of the extrudate surface distortion, This paper studies the effect of wall slip on the numerically simulated extensional stress level at the die exit and correlates this to the experimentally determined amplitude of the surface instability. The effect of die exit radius and die wall roughness on extrusion surface instabilities is also correlated to the exit stress level in the same way. Whereas full slip may completely suppress the surface instability, a reduction in the exit stress level and instability amplitude is also shown for a rounded die exit and a slight increase in instability is shown to result from a rough die wall. A surface instability map demonstrates how the shear rate for onset of extrusion surface instabilities can be predicted on the basis of melt strength measurements and simulated stress peaks at the exit of the die. (C) 2001 Elsevier Science B.V. All rights reserved.

A risk-based system to penalize and reward line management for occupational safety and health performance

Penalizing line management for the occurrence of lost time injuries has in some cases had unintended negative consequences. These are discussed. An alternative system is suggested that penalizes line management for accidents where the combination of the probability of recurrence and the maximum reasonable consequences such a recurrence may have exceeds an agreed limit. A reward is given for prompt effective control of the risk to below the agreed risk limit. The reward is smaller than the penalty. High-risk accidents require independent investigation by a safety officer using analytical techniques. Two case examples are given to illustrate the system. Continuous safety improvement is driven by a planned reduction in the agreed risk limit over time and reward for proactive risk assessment and control.

The Tampa decision : refugee rights versus the executive's power to detain and expel unlawful non-citizens

In Ruddock and Others v Vadarlis and Others the Federal Court had to balance two fundamental but competing rights, the right of the state to secure its frontiers and the rights of individuals not to be subjected to unlawful detention - Court's task was hampered by intense public debate over the illegal refugee crisis - in the wake of 11 September 2001 and the Tampa crisis, the Federal Government has rushed through several amendments to migration laws and border protection legislation.

Applying discrete element modelling to vertical and horizontal shaft impact crushers

The PFC3D (particle flow code) that models the movement and interaction of particles by the DEM techniques was employed to simulate the particle movement and to calculate the velocity and energy distribution of collision in two types of impact crusher: the Canica vertical shaft crusher and the BJD horizontal shaft swing hammer mill. The distribution of collision energies was then converted into a product size distribution for a particular ore type using JKMRC impact breakage test data. Experimental data of the Canica VSI crusher treating quarry and the BJD hammer mill treating coal were used to verify the DEM simulation results. Upon the DEM procedures being validated, a detailed simulation study was conducted to investigate the effects of the machine design and operational conditions on velocity and energy distributions of collision inside the milling chamber and on the particle breakage behaviour. (C) 2003 Elsevier Ltd. All rights reserved.