Multilobular osteochondrosarcoma of the hard palate in a dog

A 14-year-old castrated male Rhodesian Ridgeback was presented with a history of sneezing and epistaxis. Diagnostic procedures included physical examination, regional and thoracic radiography, computed tomography and histological examination of an incisional biopsy. A multilobular osteochondrosarcoma of the hard palate with pulmonary metastases was diagnosed. Surgical resection of the primary tumour was achieved with clean margins and the defect was repaired using bilateral mucosal transposition flaps from the lips. Wound dehiscence and oesophageal stricture were postoperative complications, but these resolved with treatment. A long-term survival time of 14 months resulted, with good quality of life and function during this time.

Canine intra-nasal squamous cell carcinoma treated with chemotherapy prior to surgical resection

A 12-year-old male castrated Samoyed dog was presented with left-sided epistaxis and sneezing. Diagnostic procedures included haematology and biochemistry testing, thoracic radiography, fine needle aspiration of regional lymph nodes, CT, rhinoscopy, incisional biopsy and histopathology. Squamous cell carcinoma of the rostral nasal cavity was diagnosed, with no evidence of metastatic disease. External beam radiation was not an accessible treatment option. Complete surgical resection of the tumour would have required a larger, more disfiguring resection of nasal planum and maxilla than the owner was prepared to accept and may have been associated with an unacceptable morbidity. As an alternative, the extent of disease was reduced using a combination of carboplatin, doxorubicin and piroxicam chemotherapy. This allowed a less extensive nasal planum removal to be performed to remove residual disease with clean margins. The patient achieved a 14 month disease free interval from the time of surgery to the time of local recurrence. Survival time from diagnosis to eventual euthanasia for progressive local disease was 18 months.

HFE genotyping demonstrates a significant incidence of hemochromatosis in up differentiated arthritis

Objective Hereditary hemochromatosis is a common autosomal recessive disorder of iron metabolism. Among Northern Europeans the carrier frequency is estimated to be I in 10, while up to 1 in 200 is affected by the disease. Arthropathy is one early clinical manifestation of this disease, but the articular features are often misdiagnosed. In this study the two frequent mutations of the HLA-linked hemochromatosis gene (HFE) were investigated, in a rheumatology clinic population. Methods Two hundred and six consecutive patients (mean age 57.7 years; 38 male/168 female) attending a rheumatology clinic over a period of 14 months were screened for HFE mutations (C282Y and H63D). All standard diagnostic procedures were used to identify the aetiology: of the arthropathy. Mutations were evaluated by separation on PAGE of digested PCR amplificates of DNA (by SnapI and Bcl-I, for C282Y and H63D, respectively) obtained from PBMCs. Results The C282Y and H63D allele frequencies were 4.5 and 12.8 inpatients with rheumatic diseases. Five patients were homozygote for H63D (2.4%), and one,for C282Y (0.5%). Five patients were compound heterozygous (2.4%). The observed C282Y allele frequency in rheumatic patients with undifferentiated arthritis was 12.9 and exceeded that of healthy subjects (p = 0.01). Conclusions Determination of the HFE genotype is clinically useful in patients with arthritis of unknown origin, to allow early diagnosis of hemochromatosis.

Validation of assembled nucleic acid-based tests in diagnostic microbiology laboratories

Medical microbiology and virology laboratories use nucleic acid tests (NAT) to detect genomic material of infectious organisms in clinical samples. Laboratories choose to perform assembled (or in-house) NAT if commercial assays are not available or if assembled NAT are more economical or accurate. One reason commercial assays are more expensive is because extensive validation is necessary before the kit is marketed, as manufacturers must accept liability for the performance of their assays, assuming their instructions are followed. On the other hand, it is a particular laboratory's responsibility to validate an assembled NAT prior to using it for testing and reporting results on human samples. There are few published guidelines for the validation of assembled NAT. One procedure that laboratories can use to establish a validation process for an assay is detailed in this document. Before validating a method, laboratories must optimise it and then document the protocol. All instruments must be calibrated and maintained throughout the testing process. The validation process involves a series of steps including: (i) testing of dilution series of positive samples to determine the limits of detection of the assay and their linearity over concentrations to be measured in quantitative NAT; (ii) establishing the day-to-day variation of the assay's performance; (iii) evaluating the sensitivity and specificity of the assay as far as practicable, along with the extent of cross-reactivity with other genomic material; and (iv) assuring the quality of assembled assays using quality control procedures that monitor the performance of reagent batches before introducing new lots of reagent for testing.

Diagnostic goal driven modelling and simulation of multiscale process systems

A systematic goal-driven top-down modelling methodology is proposed that is capable of developing a multiscale model of a process system for given diagnostic purposes. The diagnostic goal-set and the symptoms are extracted from HAZOP analysis results, where the possible actions to be performed in a fault situation are also described. The multiscale dynamic model is realized in the form of a hierarchical coloured Petri net by using a novel substitution place-transition pair. Multiscale simulation that focuses automatically on the fault areas is used to predict the effect of the proposed preventive actions. The notions and procedures are illustrated on some simple case studies including a heat exchanger network and a more complex wet granulation process.

Tailoring surface properties to build colloidal diagnostic devices: Controlling interparticle associations

The ability to control the surface properties and subsequent colloidal stability of dispersed particles has widespread applicability in many fields. Sub-micrometer fluorescent silica particles (reporters) can be used to actively encode the combinatorial synthesis of peptide libraries through interparticle association. To achieve these associations, the surface chemistry of the small fluorescent silica reporters is tailored to encourage robust adhesion to large silica microparticles onto which the peptides are synthesized. The interparticle association must withstand a harsh solvent environment multiple synthetic and washing procedures, and biological screening buffers. The encoded support beads were exposed to different solvents used for peptide synthesis, and different solutions used for biological screening including phosphate buffered saline (PBS), 2-[N-morpholino]ethane sulfonic acid (VIES) and a mixture of MES and N-(3-dimethyl-aminopropyl)-N'-ethylcarbodiimide (EDC). The number of reporters remaining adhered to the support bead was quantified after each step. The nature of the associations were explored and tested to optimize the efficiency of these phenomena. Results presented illustrate the influence of the surface functionality and polyelectrolyte modification of the reporters. These parameters were investigated through zeta potential and X-ray photoelectron spectroscopy.