A review of flow modeling for dense medium cyclones

A critical assessment is presented for the existing fluid flow models used for dense medium cyclones (DMCs) and hydrocyclones. As the present discussion indicates, the understanding of dense medium cyclone flow is still far from the complete. However, its similarity to the hydrocyclone provides a basis for improved understanding of fluid flow in DMCs. The complexity of fluid flow in DMCs is basically due to the existence of medium as well as the dominance of turbulent particle size and density effects on separation. Both the theoretical and experimental analysis is done with respect to two-phase motions and solid phase flow in hydrocyclones or DMCs. A detailed discussion is presented on the empirical, semiempirical, and the numerical models based upon both the vorticity-stream function approach and Navier-Stokes equations in their primitive variables and in cylindrical coordinates available in literature. The existing equations describing turbulence and multiphase flows in cyclone are also critically reviewed.

A Century of Change in Coral Reef Status in Southeast and Central Pacific: Polynesia Mana Node, Cook Islands, French Polynesia, Kiribati, Niue, Tokelau, Tonga, Wallis and Futuna

The Polynesia Mana Node of the southeast and central Pacific contains 7 independent or autonomous countries or territories with only 6,000 km2 of land on 347 islands, but surrounded by 12 million km2 of EEZ. These seas contain 13,000 km2 of coral reefs as the main natural ecosystem providing food resources and opportunities for development, especially for tourism and pearl culture for 500,000 inhabitants. During the 19th and first half of the 20th centuries, there was major exploitation by the colonial powers of mother-of-pearl oysters for the button industry, as well as guano, sandalwood and trepang. The Polynesian people were largely involved in a subsistence economy and all coral reefs and lagoons were healthy. During the last two decades of the 20th, all countries experienced rapid development and urbanization, rising populations, and some increased agriculture. These developments were limited to a few islands of each country (i.e. 15 islands amongst the 347) with resulting degradation of the coral reefs around these sites. The other islands remained mostly uninhabited and pristine, and continued with a subsistence economy. Generally, there was more damage to the coral reefs through natural events such as cyclones and coral bleaching, than by human activities. There is however, an urgent need to combat the threats on some islands from increased sedimentation, over-fishing, dredging and nutrient pollution.

The JK three-product cyclone - performance and potential applications

In spite of their wide application in comminution circuits, hydrocyclones have at least one significant disadvantage in that their operation inherently tends to return the fine denser liberated minerals to the grinding mill. This results in unnecessary overgrinding which adds to the milling cost and can adversely affect the efficiency of downstream processes. In an attempt to solve this problem, a three-product cyclone has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to generate a second overflow in which the fine dense liberated minerals can be selectively concentrated for further treatment. In this paper, the design and operation of the three-product cyclone are described. The influence of the length of the second vortex finder on the performance of a 150-mm unit treating a mixture of magnetite and silica is investigated. Conventional cyclone tests were also conducted under similar conditions. Using the operational performance data of the three-product and conventional cyclones, it is shown that by optimising the length of the second vortex finder, the amount of fine dense mineral particles that reports to the three-product cyclone underflow can be reduced. In addition, the three-product cyclone can be used to generate middlings stream that may be more suitable for flash flotation than the conventional cyclone underflow, or alternatively, could be classified with a microscreen to separate the valuables from the gangue. At the same time, a fines stream having similar properties to those of the conventional overflow can be obtained. Hence, if the middlings stream was used as feed for flash flotation or microscreening, the fines stream could be used in lieu of the conventional overflow without compromising the feed requirements for the conventional flotation circuit. Some of the other potential applications of the new cyclone are described. (C) 2003 Elsevier Science B.V. All rights reserved.

Development of a more efficient classifying cyclone

A more efficient classifying cyclone (CC) for fine particle classification has been developed in recent years at the JKMRC. The novel CC, known as the JKCC, has modified profiles of the cyclone body, vortex finder, and spigot when compared to conventional hydrocyclones. The novel design increases the centrifugal force inside the cyclone and mitigates the short circuiting flow that exists in all current cyclones. It also decreases the probability of particle contamination in the place near the cyclone spigot. Consequently the cyclone efficiency is improved while the unit maintains a simple structure. An international patent has been granted for this novel cyclone design. In the first development stage-a feasibility study-a 100 mm JKCC was tested and compared with two 100 min commercial units. Very encouraging results were achieved, indicating good potential for the novel design. In the second development stage-a scale-up stage-the JKCC was scaled up to 200 mm in diameter, and its geometry was optimized through numerous tests. The performance of the JKCC was compared with a 150 nun commercial unit and exhibited sharper separation, finer separation size, and lower flow ratios. The JKCC is now being scaled up into a fill-size (480 mm) hydrocyclone in the third development stage-an industrial study. The 480 mm diameter unit will be tested in an Australian coal preparation plant, and directly compared with a commercial CC operating under the same conditions. Classifying cyclone performance for fine coal could be further improved if the unit is installed in an inclined position. The study using the 200 mm JKCC has revealed that sharpness of separation improved and the flow ratio to underflow was decreased by 43% as the cyclone inclination was varied from the vertical position (0degrees) to the horizontal position (90degrees). The separation size was not affected, although the feed rate was slightly decreased. To ensure self-emptying upon shutdown, it is recommended that the JKCC be installed at an inclination of 75-80degrees. At this angle the cyclone performance is very similar to that at a horizontal position. Similar findings have been derived from the testing of a conventional hydrocyclone. This may be of benefit to operations that require improved performance from their classifying cyclones in terms of sharpness of separation and flow ratio, while tolerating slightly reduced feed rate.

Monarchs in Australia: On the winds of a storm?

The monarch butterfly, Danaus plexippus, is one of Australia's best-known exotic butterflies, being first recorded here in the spring/summer of 1870/1871. However, the source of the original population is unknown. Using historical records we suggest that the most likely source of the founder population was from Vanuatu and/or New Caledonia. Many almost simultaneous 'first records' for the butterfly in Australia suggest that a large, well-distributed population was present when first noticed. While such a population may have developed from a limited number of individuals flying across the Coral Sea, the well documented, very dramatic appearance of large monarch populations in Australia does not appear to fit this model. Rather, we hypothesise that large numbers of monarchs were carried to Australia on cyclonic winds: no fewer that 3 cyclones hit the Queensland coast in early 1870. If one or more of these cyclones tracked from the Vanuatu/New Caledonia chain, then they may have transported monarchs. Once established on the central/northern Queensland coast, natural migration would account for the appearance of butterflies further south.

Slurry flow in mills with TCPL - An efficient pulp lifter for ag/sag mills

The difficulties associated with slurry transportation in autogenous (ag) and semi-autogenous (sag) grinding mills have become more apparent in recent years with the increasing trend to build larger diameter mills for grinding high tonnages. This is particularly noticeable when ag/sag mills are run in closed circuit with classifiers such as fine screens/cyclones. Extensive test work carried out on slurry removal mechanism in grate discharge mills (ag/sag) has shown that the conventional pulp lifters (radial and curved) have inherent drawbacks. They allow short-circuiting of the slurry from pulp lifters into the grinding chamber leading to slurry pool formation. Slurry pool absorbs part of the impact thus inhibiting the grinding process. Twin Chamber Pulp Lifter (TCPL) - an efficient design of pulp lifter developed by the authors overcomes the inherent drawbacks of the conventional pulp lifters. Extensive testing in both laboratory and pilot scale mills has shown that the TCPL completely blocks the flow-back process, thus allowing the mill to operate close to their design flow capacity. The TCPL performance is also found to be independent of variations in charge volume and grate design, whereas they significantly affect the performance of conventional pulp lifters (radial and curved). (c) 2006 Elsevier B.V. All rights reserved.

Numerical simulation of magnetite segregation in a dense medium cyclone

Numerical simulations of turbulent driven flow in a dense medium cyclone with magnetite medium have been conducted using Fluent. The predicted air core shape and diameter were found to be close to the experimental results measured by gamma ray tomography. It is possible that the Large eddy simulation (LES) turbulence model with Mixture multi-phase model can be used to predict the air/slurry interface accurately although the LES may need a finer grid. Multi-phase simulations (air/water/medium) are showing appropriate medium segregation effects but are over-predicting the level of segregation compared to that measured by gamma-ray tomography in particular with over prediction of medium concentrations near the wall. Further, investigated the accurate prediction of axial segregation of magnetite using the LES turbulence model together with the multi-phase mixture model and viscosity corrections according to the feed particle loading factor. Addition of lift forces and viscosity correction improved the predictions especially near the wall. Predicted density profiles are very close to gamma ray tomography data showing a clear density drop near the wall. The effect of size distribution of the magnetite has been fully studied. It is interesting to note that the ultra-fine magnetite sizes (i.e. 2 and 7 mu m) are distributed uniformly throughout the cyclone. As the size of magnetite increases, more segregation of magnetite occurs close to the wall. The cut-density (d(50)) of the magnetite segregation is 32 gm, which is expected with superfine magnetite feed size distribution. At higher feed densities the agreement between the [Dungilson, 1999; Wood, J.C., 1990. A performance model for coal-washing dense medium cyclones, Ph.D. Thesis, JKMRC, University of Queensland] correlations and the CFD are reasonably good, but the overflow density is lower than the model predictions. It is believed that the excessive underflow volumetric flow rates are responsible for under prediction of the overflow density. (c) 2006 Elsevier Ltd. All rights reserved.