SCC initiation for X65 pipeline steel in the "high" pH carbonate/bicarbonate solution

The initiation of stress corrosion cracking (SCC) was studied using scanning electron microscope observations of linearly increasing stress test specimens. SCC initiation from the following surfaces was studied: (i) initiation from the commercial pipe surface covered by the Zn coating, (ii) initiation from a mechanically polished surface with a deformed layer, and (iii) initiation from an electro-polished surface. SCC initiation involved different features for these surfaces as follows. (i) For the Zn coated commercial pipe surface, a crack in the Zn coating led to the dissolution of the deformed layer and when the deformed layer was penetrated, intergranular SCC initiation became possible. (ii) For a mechanically polished surface with a deformed layer, cracks in the surface oxide concentrated the anodic dissolution to such an extent that there was transgranular SCC in the deformed layer. SCC was intergranular when the deformed layer had been penetrated. Transgranular stress corrosion cracks were stopped at ferrite grain boundaries (GBs) oriented perpendicular to the SCC propagation direction. (iii) For an electro-polished surface, the surface oxide film was cracked at many locations, but intergranular SCC only propagated into the steel when the oxide crack corresponded to a GB. An oxide crack away from a GB is expected to be healed. The observed SCC initiation mechanism was not associated with simple preferential chemical attack of the ferrite GBs. (C) 2003 Elsevier Ltd. All rights reserved.

Impact of alternative initiation, splicing, and termination on the diversity of the mRNA transcripts encoded by the mouse transcriptome

We analyzed the FANTOM2 clone set of 60,770 RIKEN full-length mouse cDNA sequences and 44,122 public mRNA sequences. We developed a new computational procedure to identify and classify the forms of splice variation evident in this data set and organized the results into a publicly accessible database that can be used for future expression array construction, structural genomics, and analyses of the mechanism and regulation of alternative splicing. Statistical analysis shows that at least 41% and possibly as much as 60% of multiexon genes in mouse have multiple splice forms. Of the transcription units with multiple splice forms, 49% contain transcripts in which the apparent use of an alternative transcription start (stop) is accompanied by alternative splicing of the initial (terminal) exon. This implies that alternative transcription may frequently induce alternative splicing. The fact that 73% of all exons with splice variation fall within the annotated coding region indicates that most splice variation is likely to affect the protein form. Finally, we compared the set of constitutive (present in all transcripts) exons with the set of cryptic (present only in some transcripts) exons and found statistically significant differences in their length distributions, the nucleoticle distributions around their splice junctions, and the frequencies of occurrence of several short sequence motifs.

Engineering mRNA translation initiation to enhance transient gene expression in Chinese hamster ovary cells

To increase transient expression of recombinant proteins in Chinese hamster ovary cells, we have engineered their protein synthetic capacity by directed manipulation of mRNA translation initiation. To control this process we constructed a nonphosphorylatable Ser51Ala site-directed mutant of eIF2, a subunit of the trimeric eIF2 complex that is implicated in regulation of the global rate of mRNA translation initiation in eukaryotic cells. Phosphorylation of eIF2 by protein kinases inhibits eIF2 activity and is known to increase as cells perceive a range of stress conditions. Using single-and dual-gene plasmids introduced into CHO cells by electroporation, we found that transient expression of the eIF2 Ser51Ala mutant with firefly luciferase resulted in a 3-fold increase in reporter activity, relative to cells transfected with reporter only. This effect was maintained in transfected cells for at least 48 h after transfection. Expression of the wild-type eIF2 protein had no such effect. Elevated luciferase activity was associated with a reduction in the level of eIF2 phosphorylation in cells transfected with the mutant eIF2 construct. Transfection of CHO cells with the luciferase-only construct resulted in a marked decrease in the global rate of protein synthesis in the whole cell population 6 h post-transfection. However, expression of the mutant Ser51Ala or wild-type eIF2 proteins restored the rate of protein synthesis in transfected cells to a level equivalent to or exceeding that of control cells. Associated with this, entry of plasmid DNA into cells during electroporation was visualized by confocal microscopy using a rhodamine-labeled plasmid construct expressing green fluorescent protein. Six hours after transfection, plasmid DNA was present in all cells, albeit to a variable extent. These data suggest that entry of naked DNA into the cell itself functions to inhibit protein synthesis by signaling mechanisms affecting control of mRNA translation by eIF2. This work therefore forms the basis of a rational strategy to generically up-regulate transient expression of recombinant proteins by simultaneous host cell engineering.

The epidemiology and genetics of smoking initiation and persistence: Crosscultural comparisons of twin study results

We examined whether there are crosscultural differences in the magnitude of genetic and environmental contributions to risk of becoming a regular smoker and of persistence in smoking in men and women. Standard methods of epidemiologic and genetic analysis were applied to questionnaire data on history of cigarette use obtained from large samples of male and female like-sex twins from three different countries: Australia (N = 2284 pairs), Sweden (N = 8651 pairs), and Finland (N = 10,948 pairs). Samples were subdivided into three age groups (AG), 18-25 years, 26-35 years, and 36-46 years of age. The magnitude of genetic influence for lifetime smoking was found to be consistent across country and AG for women (46%) and men (57%), and estimates of the contribution from environmental influences shared by twin and co-twin could be equated across all countries by AG for the women (from youngest to oldest AG: 45%, 35%, and 26%), but not for men, with separate estimates obtained for the Scandinavian (33%, 29%, and 19%) and the Australian men (26%, 9%, and 11 %). There was no evidence for an important role for shared environmental influences on persistent smoking, and the genetic contribution was found to be consistent in magnitude in men and women, and the same across country and AG (52%). There are strong genetic influences on smoking behavior, and that risk of becoming a smoker (but not persistence in smoking) may be modified by experiences shared by twins that differ by AG and, at least for men, cultural background.

Initiation of fungal epizootics in diamondback moth populations within a large field cage: proof of concept for auto-dissemination

Adult diamondback moths (DBM), Plutella xylostella L. (Lepidoptera: Plutellidae), inoculated with the fungus Zoophthora radicans, were released within a large field cage containing DBM-infested potted broccoli plants. Larvae and pupae on exposed and caged control plants were examined on five occasions over the next 48 days for evidence of Z. radicans infection. Infected larvae were first detected on exposed plants 4 days after the initial release of adults, and after 48 days the infection level reached 79%. Aerially borne conidia were a factor in transmission of the fungus. Infection had no effect on possible losses of larval and adult cadavers due to scavengers in field crops. In a trial to measure the influence of infection on dispersal, twice as many non-infected as infected males were recaptured in pheromone traps, although the difference in cumulative catch only became significant 3 days after release of the males. In a separate experiment, when adult moths were inoculated with Beauveria bassiana conidia and released into the field cage, DBM larvae collected from 37 of 96 plants sampled 4 days later subsequently died from B. bassiana infection. The distribution of plants from which the infected larvae were collected was random, but the distribution of infected larvae was clustered within the cage. These findings suggest that the auto-dissemination of fungal pathogens may be a feasible strategy for DBM control, provided that epizootics can be established and maintained when DBM population densities are low.

Initiation of evasive manoeuvres during self-motion: a test of three hypotheses

To understand performance of evasive and interceptive actions it is important to know how people decide when to initiate a movement - initiating at the 'right' moment is often essential for successful performance. It has been proposed that initiation is triggered when a perceptually derived quantity reaches an invariant criterion value. Candidate quantities include time-to-collision (TTC), distance, and rate of image expansion ( ROE), all of which have received empirical support. We studied initiation of an evasive manoeuvre in a computer-simulated steering task in which the observer was required to steer through a stationary visual environment and avoid colliding with an obstacle in their path. The results could not be explained by hypotheses which propose that evasive manoeuvre initiation is based on a fixed criterion value of TTC or distance. The overall pattern was, however, consistent with the use of a criterion ROE value. This was further tested by analyses designed to directly evaluate whether the ROE value used to initiate the response was the same across experimental conditions. Only two of the six participants showed evidence for using the ROE strategy.

Effect of addition of maltodextrin on drying kinetics and stickiness of sugar and acid-rich foods during convective drying: experiments and modelling

The effect of addition of maltodextrin on drying kinetics of drops containing fructose, glucose, sucrose and citric acid individually and in mixtures was studied experimentally using single drop drying experiments and numerically by solving appropriate mass and heat transfer equations. The numerical predictions agreed with the experimental moisture and temperature histories within 5-6% average relative (absolute) errors and average differences of +/- 1degreesC, respectively. The stickiness of these drops was determined using the glass transition temperature (T-g) of the drops' surface layer as an indicator. The experimental stickiness histories followed the model predictions with reasonable accuracy. A safe drying (non-sticky) regime in a spray drying environment has been proposed, and used to estimate the optimum amount of addition of maltodextrin for successful spray drying of 120 micron diameter droplets of fruit juices. (C) 2003 Elsevier Ltd. All rights reserved.

Theoretical investigation of convective instability in inclined and fluid-saturated three-dimensional fault zones.

The convective instability of pore-fluid flow in inclined and fluid-saturated three-dimensional fault zones has been theoretically investigated in this paper. Due to the consideration of the inclined three-dimensional fault zone with any values of the inclined angle, it is impossible to use the conventional linear stability analysis method for deriving the critical condition (i.e., the critical Rayleigh number) which can be used to investigate the convective instability of the pore-fluid flow in an inclined three-dimensional fault zone system. To overcome this mathematical difficulty, a combination of the variable separation method and the integration elimination method has been used to derive the characteristic equation, which depends on the Rayleigh number and the inclined angle of the inclined three-dimensional fault zone. Using this characteristic equation, the critical Rayleigh number of the system can be numerically found as a function of the inclined angle of the three-dimensional fault zone. For a vertically oriented three-dimensional fault zone system, the critical Rayleigh number of the system can be explicitly derived from the characteristic equation. Comparison of the resulting critical Rayleigh number of the system with that previously derived in a vertically oriented three-dimensional fault zone has demonstrated that the characteristic equation of the Rayleigh number is correct and useful for investigating the convective instability of pore-fluid flow in the inclined three-dimensional fault zone system. The related numerical results from this investigation have indicated that: (1) the convective pore-fluid flow may take place in the inclined three-dimensional fault zone; (2) if the height of the fault zone is used as the characteristic length of the system, a decrease in the inclined angle of the inclined fault zone stabilizes the three-dimensional fundamental convective flow in the inclined three-dimensional fault zone system; (3) if the thickness of the stratum is used as the characteristic length of the system, a decrease in the inclined angle of the inclined fault zone destabilizes the three-dimensional fundamental convective flow in the inclined three-dimensional fault zone system; and that (4) the shape of the inclined three-dimensional fault zone may affect the convective instability of pore-fluid flow in the system. (C) 2004 Published by Elsevier B.V.

Observation of crack initiation during hot tearing

While the general mechanisms of hot tearing are understood, i.e. the inability of liquid to feed imposed strain on the mushy material, work continues on improving the understanding of the mechanisms at play. A hot tear test rig that measures the temperature and load imposed on the mushy zone during solidification has been successfully used to study hot tearing. The mould has now been modified to incorporate a window above the hot spot region to allow observation of hot tear formation and growth. Combining information from visual observation with load and temperature data has led to a better understanding of the mechanism of hot tearing. Tests were carried out on an Al-0.5 wt-% Cu alloy. It was found that load development began at about 90% solid and a hot tear formed a short time later, at between 93% and 96% solid. Hot tearing started at a very low load.

The implications of simultaneous smoking initiation for inferences about the genetics of smoking behavior from twin data

We examined early social influences across stages of smoking within the context of a twin study using an environmental exposure specific to smoking: whether twins started smoking at the same time (simultaneous smoking initiation: SSI). We expected that SSI would be a good index of shared social influences on smoking initiation. Rates of SSI were indeed significantly higher in MZ twins and in twins who shared peers and classes, as well as in male twins. With the exception of regular smoking in females, we found no significant difference in estimates of genetic and environmental parameters between SSI and non-SSI pairs for any of the smoking measures that we examined (DSM-IV and Fagerstrom HSI measures of nicotine dependence; DSM-IV nicotine withdrawal; heavy smoking; and in males, regular smoking). For regular smoking in females, allowing for additional shared environmental influences associated with SSI only modestly reduced our estimates of additive genetic variance (56% vs. 68%). These results indicate the important social influences that may occur for smoking initiation do not appear to seriously bias estimates of genetic effects on later stages of smoking.

Changes in the initiation of heroin use after a reduction in heroin supply

Increasing heroin use in Australia over the past 30 years has been associated with a decline in the age of initiation to heroin use. The 2001 Australian heroin shortage was used to assess the effects of a reduction in heroin supply on age of initiation into heroin injecting. Data collected from regular injecting drug users (IDU) over the period 1996-2004 as part of the Australian Illicit Drug Reporting System were examined for changes in self- reported age of first heroin use after the onset of the heroin shortage. Estimates were also made of the number of young people who may not have commenced injecting heroin during the heroin shortage. The proportion of IDU interviewed in the IDRS who were aged

Experimental and analytical study of the effect of contact angle on liquid convective heat transfer in microchannels

In this paper we examine the effect of contact angle (or surface wettability) on the convective heat transfer coefficient in microchannels. Slip flow, where the fluid velocity at the wall is non-zero, is most likely to occur in microchannels due to its dependence on shear rate or wall shear stress. We show analytically that for a constant pressure drop, the presence of slip increases the Nusselt number. In a microchannel heat exchanger we modified the surface wettability from a contact angle of 20 degrees-120 degrees using thin film coating technology. Apparent slip flow is implied from pressure and flow rate measurements with a departure from classical laminar friction coefficients above a critical shear rate of approximately 10,000 s(-1). The magnitude of this departure is dependant on the contact angle with higher contact angles surfaces exhibiting larger pressure drop decreases. Similarly, the non-dimensional heat flux is found to decrease relative to laminar non-slip theory, and this decrease is also a function of the contact angle. Depending on the contact angle and the wall shear rate, variations in the heat transfer rate exceeding 10% can be expected. Thus the contact angle is an important consideration in the design of micro, and even more so, nano heat exchangers. (c) 2006 Elsevier Ltd. All rights reserved.

Genetic and Cultural Transmission of Smoking Initiation: An Extended Twin Kinship Model

Background Considerable evidence from twin and adoption studies indicates that genetic and shared environmental factors play a significant role in the initiation of smoking behavior. Although twin and adoption designs are powerful to detect genetic and environmental influences, they do not provide information on the processes of assortative mating and parent–offspring transmission and their contribution to the variability explained by genetic and/or environmental factors. Methods We examined the role of genetic and environmental factors for smoking initiation using an extended kinship design. This design allows the simultaneous testing of additive and non-additive genetic, shared and individual-specific environmental factors, as well as sex differences in the expression of genes and environment in the presence of assortative mating and combined genetic and cultural transmission. A dichotomous lifetime smoking measure was obtained from twins and relatives in the Virginia 30,000 sample. Results Results demonstrate that both genetic and environmental factors play a significant role in the liability to smoking initiation. Major influences on individual differences appeared to be additive genetic and unique environmental effects, with smaller contributions from assortative mating, shared sibling environment, twin environment, cultural transmission and resulting genotype–environment covariance. The finding of negative cultural transmission without dominance led us to investigate more closely two possible mechanisms for the lower parent–offspring correlations compared to the sibling and DZ twin correlations in subsets of the data: (i) age × gene interaction, and (ii) social homogamy. Neither mechanism provided a significantly better explanation of the data, although age regression was significant. Conclusions This study showed significant heritability, partly due to assortment, and significant effects of primarily non-parental shared environment on smoking initiation.

A longitudinal controlled study of factors associated with mutans streptococci infection and caries lesion initiation in children 21 to 72 months old

Purpose: The purpose of this longitudinal study was to determine factors associated with mutans streptococci (MS) infection and development of caries lesions in a group of children 21 to 72 months old. Methods: The 63 caries-free children, recruited since birth, were divided into: (1) a study group of 24 children who were colonized with MS; and (2) a control group of 39 children without MS. The children were recalled every 3 months for approximately 24 months, and their social, medical, and dental histories were updated. At each recall, the teeth were checked for presence or absence of plaque, enamel hypoplasia, and caries lesions, and their MS status was assessed using a commercial test kit. Results: MS infection was associated with: (1) visible plaque (P < .01); (2) enamel hypoplasia (P < .05); (3) commencement of tooth-brushing after 12 months of age (P < .05); (4) lack of parental assistance with tooth-brushing (P < .025); and (5) increased hours of child care/school (P < .05). Four children (20%) were colonized at an age range of 21 to 36 months, 9 (45%) at 37 to 48 months, and 7 (35%) at 49 to 72 months (P < .001). Eight children who developed caries lesions: (1) had more hypoplastic teeth (P < .001); (2) ate sugar-containing snacks (P < .05); and (3) did not brush regularly with chlorhexidine gel (P < .01) compared to those who remained free of caries lesions. Conclusions: Lack of oral hygiene, consumption of sugar-containing snacks, and enamel hypoplasia are significant factors for both MS infection and caries lesion initiation.