Practical scheme for error control using feedback

We describe a scheme for quantum-error correction that employs feedback and weak measurement rather than the standard tools of projective measurement and fast controlled unitary gates. The advantage of this scheme over previous protocols [for example, Ahn Phys. Rev. A 65, 042301 (2001)], is that it requires little side processing while remaining robust to measurement inefficiency, and is therefore considerably more practical. We evaluate the performance of our scheme by simulating the correction of bit flips. We also consider implementation in a solid-state quantum-computation architecture and estimate the maximal error rate that could be corrected with current technology.

Global control and fast solid-state donor electron spin quantum computing

We propose a scheme for quantum information processing based on donor electron spins in semiconductors, with an architecture complementary to the original Kane proposal. We show that a naive implementation of electron spin qubits provides only modest improvement over the Kane scheme, however through the introduction of global gate control we are able to take full advantage of the fast electron evolution timescales. We estimate that the latent clock speed is 100-1000 times that of the nuclear spin quantum computer with the ratio T-2/T-ops approaching the 10(6) level.

High-fidelity measurement and quantum feedback control in circuit QED

Circuit QED is a promising solid-state quantum computing architecture. It also has excellent potential as a platform for quantum control-especially quantum feedback control-experiments. However, the current scheme for measurement in circuit QED is low efficiency and has low signal-to-noise ratio for single-shot measurements. The low quality of this measurement makes the implementation of feedback difficult, and here we propose two schemes for measurement in circuit QED architectures that can significantly improve signal-to-noise ratio and potentially achieve quantum-limited measurement. Such measurements would enable the implementation of quantum feedback protocols and we illustrate this with a simple entanglement-stabilization scheme.

A bang-bang PLL employing dynamic gain control for low jitter and fast lock times

Bang-bang phase detector based PLLs are simple to design, suffer no systematic phase error, and can run at the highest speed a process can make a working flip-flop. For these reasons designers are employing them in the design of very high speed Clock Data Recovery (CDR) architectures. The major drawback of this class of PLL is the inherent jitter due to quantized phase and frequency corrections. Reducing loop gain can proportionally improve jitter performance, but also reduces locking time and pull-in range. This paper presents a novel PLL design that dynamically scales its gain in order to achieve fast lock times while improving fitter performance in lock. Under certain circumstances the design also demonstrates improved capture range. This paper also analyses the behaviour of a bang-bang type PLL when far from lock, and demonstrates that the pull-in range is proportional to the square root of the PLL loop gain.

Biologically inspired joint control for a humanoid robot

The GuRm is a 1.2m tall, 23 degree of freedom humanoid consuucted at the University of Queensland for research into humanoid robotics. The key challenge being addressed by the GuRw projcct is the development of appropriate learning strategies for control and coodinadon of the robot’s many joints. The development of learning strategies is Seen as a way to sidestep the inherent intricacy of modeling a multi-DOP biped robot. This paper outlines the approach taken to generate an appmpria*e control scheme for the joinis of the GuRoo. The paper demonsrrates the determination of local feedback control parameters using a genetic algorithm. The feedback loop is then augmented by a predictive modulator that learns a form of feed-fonward control to overcome the irregular loads experienced at each joint during the gait cycle. The predictive modulator is based on thc CMAC architecture. Results from tats on the GuRoo platform show that both systems provide improvements in stability and tracking of joint control.

A reference architecture for instructional educational software

Our extensive research has indicated that high-school teachers are reluctant to make use of existing instructional educational software (Pollard, 2005). Even software developed in a partnership between a teacher and a software engineer is unlikely to be adopted by teachers outside the partnership (Pollard, 2005). In this paper we address these issues directly by adopting a reusable architectural design for instructional educational software which allows easy customisation of software to meet the specific needs of individual teachers. By doing this we will facilitate more teachers regularly using instructional technology within their classrooms. Our domain-specific software architecture, Interface-Activities-Model, was designed specifically to facilitate individual customisation by redefining and restructuring what constitutes an object so that they can be readily reused or extended as required. The key to this architecture is the way in which the software is broken into small generic encapsulated components with minimal domain specific behaviour. The domain specific behaviour is decoupled from the interface and encapsulated in objects which relate to the instructional material through tasks and activities. The domain model is also broken into two distinct models - Application State Model and Domainspecific Data Model. This decoupling and distribution of control gives the software designer enormous flexibility in modifying components without affecting other sections of the design. This paper sets the context of this architecture, describes it in detail, and applies it to an actual application developed to teach high-school mathematical concepts.