The effect of grain refinement and cooling rate on the hot tearing of wrought aluminium alloys

Using modifications to the Rappaz-Drezet-Gremaud hot tearing model, and using empirical equations developed for grain size and dendrite arm spacing (DAS) on the addition of grain refiner for a range of cooling rates, the effect of grain refinement and cooling rate on hot tearing susceptibility has been analysed. It was found that grain refinement decreased the grain size and made the grain morphology more globular. Therefore refining the grain size of an equiaxed dendritic grain decreased the hot tearing susceptibility. However, when the alloy was grain refined such that globular grain morphologies where obtained, further grain refinement increased the hot tearing susceptibility. Increasing the cooling decreased the grain size and made the grain morphology more dendritic and therefore increased the likelihood of hot tearing. The effect was particularly strong for equiaxed dendritic grain morphologies; hence grain refinement is increasingly important at high cooling rates to obtain more globular grain morphologies to reduce the hot tearing susceptibility.

Dendrite coherency of Al-Si-Cu alloys

The dendrite coherency point of Al-Si-Cu alloys was determined by thermal analysis and rheological measurement methods by performing parallel measurements at two cooling rates for aluminum alloys across a wide range of silicon and copper contents. Contrary to previous findings, the two methods yield significantly different values for the fraction solid at the dendrite coherency point. This disparity is greatest for alloys of low solute concentration. The results from this study also contradict previously reported tl ends in the effect of cooling rate on the dendritic coherency point. Consideration of the results shows that thermal analysis is not a valid technique for the measurement of coherency. Analysis of the results from rheological testing indicates that silicon concentration has a dominant effect on grain size and dendritic morphology, independent of cooling rate and copper content, and thus is the factor that determines the fraction solid at dendrite coherency for Al-Si-Cu alloys.

Grain coarsening of magnesium alloys by beryllium

A trace of beryllium can lead to dramatic grain coarsening in Mg-Al alloys at normal cooling rates. It is, however, unclear whether this effect applies to aluminium-free magnesium alloys or not. This work shows that a trace of beryllium also causes considerable grain coarsening in Mg-Zn, Mg-Ca, Mg-Ce and Mg-Nd alloys and hinders grain refinement of magnesium alloys by zirconium as well. (C) 2004 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Non-Equilibrium Reaction Rates in the Macroscopic Chemistry Method for DSMC Calculations

The Direct Simulation Monte Carlo (DSMC) method is used to simulate the flow of rarefied gases. In the Macroscopic Chemistry Method (MCM) for DSMC, chemical reaction rates calculated from local macroscopic flow properties are enforced in each cell. Unlike the standard total collision energy (TCE) chemistry model for DSMC, the new method is not restricted to an Arrhenius form of the reaction rate coefficient, nor is it restricted to a collision cross-section which yields a simple power-law viscosity. For reaction rates of interest in aerospace applications, chemically reacting collisions are generally infrequent events and, as such, local equilibrium conditions are established before a significant number of chemical reactions occur. Hence, the reaction rates which have been used in MCM have been calculated from the reaction rate data which are expected to be correct only for conditions of thermal equilibrium. Here we consider artificially high reaction rates so that the fraction of reacting collisions is not small and propose a simple method of estimating the rates of chemical reactions which can be used in the Macroscopic Chemistry Method in both equilibrium and non-equilibrium conditions. Two tests are presented: (1) The dissociation rates under conditions of thermal non-equilibrium are determined from a zero-dimensional Monte-Carlo sampling procedure which simulates ‘intra-modal’ non-equilibrium; that is, equilibrium distributions in each of the translational, rotational and vibrational modes but with different temperatures for each mode; (2) The 2-D hypersonic flow of molecular oxygen over a vertical plate at Mach 30 is calculated. In both cases the new method produces results in close agreement with those given by the standard TCE model in the same highly nonequilibrium conditions. We conclude that the general method of estimating the non-equilibrium reaction rate is a simple means by which information contained within non-equilibrium distribution functions predicted by the DSMC method can be included in the Macroscopic Chemistry Method.

Frequency stabilised grating feedback laser diode for atom cooling applications

The free running linewidth of an external cavity grating feedback diode laser is on the order of a few megahertz and is limited by the mechanical and acoustic vibrations of the external cavity. Such frequency fluctuations can be removed by electronic feedback. We present a hybrid stabilisation technique that uses both a Fabry-Perot confocal cavity and an atomic resonance to achieve excellent short and long term frequency stability. The system has been shown to reduce the laser linewidth of an external cavity diode laser by an order of magnitude to 140 kHz, while limiting frequency excursions to 60 kHz relative to an absolute reference over periods of several hours. The scheme also presents a simple way to frequency offset two lasers many gigahertz apart which should find a use in atom cooling experiments, where hyperfine ground-state frequency separations are often required.

Information internalization and hurdle rates in small and medium enterprise internationalization

We investigate the role of information in the internationalization of small and medium enterprises (SMEs). Information internalization is fundamentally antecedent to SME internationalization and is being facilitated increasingly by recent important trends. We offer a conceptual explanation and related propositions on information internalization, emphasizing hurdle rate theory for ascertaining the acceptability of firms' internationalization projects.

Whole-body pre-cooling and heat storage during self-paced cycling performance in warm humid conditions

The aim of this study was to establish the effect that pre-cooling the skin without a concomitant reduction in core temperature has on subsequent self-paced cycling performance under warm humid (31 degrees C and 60% relative humidity) conditions. Seven moderately trained males performed a 30 min self-paced cycling trial on two separate occasions. The conditions were counterbalanced as control or whole-body pre-cooling by water immersion so that resting skin temperature was reduced by approximate to 5-6 degrees C. After pre-cooling, mean skin temperature was lower throughout exercise and rectal temperature was lower (P < 0.05) between 15 and 25 min of exercise. Consequently, heat storage increased (P < 0.003) from 84.0 +/- 8.8 W . m(-2) to 153 +/- 13.1 W . m(-2) (mean +/- s((x) over bar)) after pre-cooling, while total body sweat fell from 1.7 +/- 0.1 1 . h(-1) to 1.2 +/- 0.1 1 . h(-1) (P < 0.05). The distance cycled increased from 14.9 +/- 0.8 to 15.8 +/- 0.7 km (P < 0.05) after pre-cooling. The results indicate that skin pre-cooling in the absence of a reduced rectal temperature is effective in reducing thermal strain and increasing the distance cycled in 30 min under warm humid conditions.

Estimation of contribution of changes in classic risk factors to trends in coronary-event rates across the WHO MONICA Project populations

Background From the mid-1980s to mid-1990s, the WHO MONICA Project monitored coronary events and classic risk factors for coronary heart disease (CHD) in 38 populations from 21 countries. We assessed the extent to which changes in these risk factors explain the variation in the trends in coronary-event rates across the populations. Methods In men and women aged 35-64 years, non-fatal myocardial infarction and coronary deaths were registered continuously to assess trends in rates of coronary events. We carried out population surveys to estimate trends in risk factors. Trends in event rates were regressed on trends in risk score and in individual risk factors. Findings Smoking rates decreased in most male populations but trends were mixed in women; mean blood pressures and cholesterol concentrations decreased, body-mass index increased, and overall risk scores and coronary-event rates decreased. The model of trends in 10-year coronary-event rates against risk scores and single risk factors showed a poor fit, but this was improved with a 4-year time lag for coronary events. The explanatory power of the analyses was limited by imprecision of the estimates and homogeneity of trends in the study populations. Interpretation Changes in the classic risk factors seem to partly explain the variation in population trends in CHD. Residual variance is attributable to difficulties in measurement and analysis, including time lag, and to factors that were not included, such as medical interventions. The results support prevention policies based on the classic risk factors but suggest potential for prevention beyond these.

Comparison of trends in method-specific suicide rates in Australia and England & Wales, 1968-97

Objective: To compare secular trends in method-specific suicide rates among young people in Australia and England & Wales between 1968 and 1997. Methods: Australian data were obtained from the Australian Bureau of Statistics, and for England & Wales from the Office for National Statistics. Overall and method-specific suicide rates for 15-34 year old males and females were calculated using ICD codes E950-9 and E980-9 except E988.8. Results: In both settings, suicide rates have almost doubled in young males over the past 30 years (from 16.8 to 32.9 per 100,000 in Australia and from 10.1 to 19.0 in England & Wales). Overall rates have changed little in young females. In both sexes and in both settings there have been substantial increases in suicide by hanging (5-7 fold increase in Australia and four-fold increase in England & Wales). There have also been smaller increases in gassing in the 1980s and '90s. In females, the impact of these increases on overall rates has been offset by a decline in drug overdose, the most common method in females. Conclusions: Rates of male suicide have increased substantially in both settings in recent years, and hanging has become an increasingly common method of suicide. The similarity in observed trends in both settings supports the view that such changes may have common causes. Research should focus on understanding why hanging has increased in popularity and what measures may be taken to diminish it.

Numerical modelling of double diffusion driven reactive flow transport in deformable fluid-saturated porous media with particular consideration of temperature-dependent chemical reaction rates

Numerical methods ave used to solve double diffusion driven reactive flow transport problems in deformable fluid-saturated porous media. in particular, thp temperature dependent reaction rate in the non-equilibrium chemical reactions is considered. A general numerical solution method, which is a combination of the finite difference method in FLAG and the finite element method in FIDAP, to solve the fully coupled problem involving material deformation, pore-fluid flow, heat transfer and species transport/chemical reactions in deformable fluid-saturated porous media has been developed The coupled problem is divided into two subproblems which are solved interactively until the convergence requirement is met. Owing to the approximate nature of the numerical method, if is essential to justify the numerical solutions through some kind of theoretical analysis. This has been highlighted in this paper The related numerical results, which are justified by the theoretical analysis, have demonstrated that the proposed solution method is useful for and applicable to a wide range of fully coupled problems in the field of science and engineering.

Evolution of stress deficit and changing rates of seismicity in cellular automaton models of earthquake faults

We investigate the internal dynamics of two cellular automaton models with heterogeneous strength fields and differing nearest neighbour laws. One model is a crack-like automaton, transferring ail stress from a rupture zone to the surroundings. The other automaton is a partial stress drop automaton, transferring only a fraction of the stress within a rupture zone to the surroundings. To study evolution of stress, the mean spectral density. f(k(r)) of a stress deficit held is: examined prior to, and immediately following ruptures in both models. Both models display a power-law relationship between f(k(r)) and spatial wavenumber (k(r)) of the form f(k(r)) similar tok(r)(-beta). In the crack model, the evolution of stress deficit is consistent with cyclic approach to, and retreat from a critical state in which large events occur. The approach to criticality is driven by tectonic loading. Short-range stress transfer in the model does not affect the approach to criticality of broad regions in the model. The evolution of stress deficit in the partial stress drop model is consistent with small fluctuations about a mean state of high stress, behaviour indicative of a self-organised critical system. Despite statistics similar to natural earthquakes these simplified models lack a physical basis. physically motivated models of earthquakes also display dynamical complexity similar to that of a critical point system. Studies of dynamical complexity in physical models of earthquakes may lead to advancement towards a physical theory for earthquakes.

Variation in mortality rates in Australia: correlation with Indigenous status, remoteness and socio-economic deprivation

Background The aim of this study was to study ecological correlations between age-adjusted all-cause mortality rates in Australian statistical divisions and (1) the proportion of residents that self-identify as Indigenous, (2) remoteness, and (3) socio-economic deprivation. Methods All-cause mortality rates for 57 statistical divisions were calculated and directly standardized to the 1997 Australian population in 5-year age groups using Australian Bureau of Statistics (ABS) data. The proportion of residents who self-identified as Indigenous was obtained from the 1996 Census. Remoteness was measured using ARIA (Accessibility and Remoteness Index for Australia) values. Socioeconomic deprivation was measured using SEIFA (Socio-Economic index for Australia) values from the ABS. Results Age-standardized all-cause mortality varies twofold from 5.7 to 11.3 per 1000 across Australian statistical divisions. Strongest correlation was between Indigenous status and mortality (r = 0.69, p < 0.001). correlation between remoteness and mortality was modest (r = 0.39, p = 0.002) as was correlation between socio-economic deprivation and mortality (r = -0.42, p = 0.001). Excluding the three divisions with the highest mortality, a multiple regression model using the logarithm of the adjusted mortality rate as the dependent variable showed that the partial correlation (and hence proportion of the variance explained) for Indigenous status was 0.03 (9 per cent; p = 0.03), for SEIFA score was -0.17 (3 per cent; p = 0.22); and for remoteness was -0.22 (5 per cent; p = 0.13). Collectively, the three variables studied explain 13 per cent of the variability in mortality. Conclusions Ecological correlation exists between all-cause mortality, Indigenous status, remoteness and disadvantage across Australia. The strongest correlation is with indigenous status, and correlation with all three characteristics is weak when the three statistical divisions with the highest mortality rates are excluded. intervention targeted at these three statistical divisions could reduce much of the variability in mortality in Australia.

Estimating HIV incidence rates from age prevalence data in epidemic situations

We present a method of estimating HIV incidence rates in epidemic situations from data on age-specific prevalence and changes in the overall prevalence over time. The method is applied to women attending antenatal clinics in Hlabisa, a rural district of KwaZulu/Natal, South Africa, where transmission of HIV is overwhelmingly through heterosexual contact. A model which gives age-specific prevalence rates in the presence of a progressing epidemic is fitted to prevalence data for 1998 using maximum likelihood methods and used to derive the age-specific incidence. Error estimates are obtained using a Monte Carlo procedure. Although the method is quite general some simplifying assumptions are made concerning the form of the risk function and sensitivity analyses are performed to explore the importance of these assumptions. The analysis shows that in 1998 the annual incidence of infection per susceptible woman increased from 5.4 per cent (3.3-8.5 per cent; here and elsewhere ranges give 95 per cent confidence limits) at age 15 years to 24.5 per cent (20.6-29.1 per cent) at age 22 years and declined to 1.3 per cent (0.5-2.9 per cent) at age 50 years; standardized to a uniform age distribution, the overall incidence per susceptible woman aged 15 to 59 was 11.4 per cent (10.0-13.1 per cent); per women in the population it was 8.4 per cent (7.3-9.5 per cent). Standardized to the age distribution of the female population the average incidence per woman was 9.6 per cent (8.4-11.0 per cent); standardized to the age distribution of women attending antenatal clinics, it was 11.3 per cent (9.8-13.3 per cent). The estimated incidence depends on the values used for the epidemic growth rate and the AIDS related mortality. To ensure that, for this population, errors in these two parameters change the age specific estimates of the annual incidence by less than the standard deviation of the estimates of the age specific incidence, the AIDS related mortality should be known to within +/-50 per cent and the epidemic growth rate to within +/-25 per cent, both of which conditions are met. In the absence of cohort studies to measure the incidence of HIV infection directly, useful estimates of the age-specific incidence can be obtained from cross-sectional, age-specific prevalence data and repeat cross-sectional data on the overall prevalence of HIV infection. Several assumptions were made because of the lack of data but sensitivity analyses show that they are unlikely to affect the overall estimates significantly. These estimates are important in assessing the magnitude of the public health problem, for designing vaccine trials and for evaluating the impact of interventions. Copyright (C) 2001 John Wiley & Sons, Ltd.