The influence of the atmosphere on the sintering of aluminum

Alloys of Al, Al-0.15Mg, and Al-12Sn made using air atomized aluminum powder and pressed to green densities of 75 to 98 pet were sintered under argon or nitrogen. Sintering in argon is only effective at high green densities when magnesium is present. In contrast, highly porous aluminum can be sintered in nitrogen without the need for magnesium. The oxygen concentration in the gas is reduced by the aluminum through a self-gettering process. The outer layers of the porous powder compact serve as a getter for the inner layers such that the oxygen partial pressure is reduced deep within the pore network. Aluminum nitride then forms, either by direct reaction with the metal or by reduction of the oxide layer, and sintering follows.

Interability interactions: Impact of type and visibility of disability on perceptions

Research on perceptions of people with disabilities has in general focussed on a single disability or on unspecified 'disability.' The aim of this study was to compare perceptions of several acquired disabilities from an intergroup perspective. It was hypothesised that the type (sensory or motor) and visibility of the disability would influence perceptions, and that prior contact would increase the positivity of perceptions. Participants were 155 students who gave their own, other, perceived self, and communication perceptions of male and female targets (with deafness, blindness, aphasia, or paraplegia) in vignettes. Results indicated that for most measures, people with motor disabilities were perceived more negatively than those with sensory ones, visible sensory disabilities more negatively than invisible sensory, but contrary to predictions, invisible motor more negatively than visible motor. There was some support for the association between prior contact and more positive perceptions.

Airborne Pinus pollen in the atmosphere of Brisbane, Australia and relationships with meteorological parameters

Relationships between weather parameters andairborne pollen loads of Pinus inBrisbane, Australia have been investigated overthe five-year period, June 1994–May 1999.Pinus pollen accounts for 4.5% of the annualairborne pollen load in Brisbane where thePinus season is confined to the winter months,July–early September. During the samplingperiod loads of 11–>100 grains m3 wererecorded on 24 days and 1–10 grains m3 on204 days. The onset and peak dates wereconsistent across each season, whereas the enddates varied. The onset of the Pinuspollen season coincided with the coolestaverage monthly temperatures (< 22°C),lowest rainfall (< 7mm), and four weeks afterdaily minimum temperatures fell to 5–9°Cin late autumn. Correlations obtained betweendaily airborne Pinus pollen counts andtemperature/rainfall parameters show thatdensities of airborne Pinus pollen arenegatively correlated with maximum temperature(p < 0.0001), minimum temperature (p < 0.0001)and rainfall (p < 0.05) during the mainpollination period. The mean duration of eachpollen season was 52 days; longer seasons wereshown to be directly related to lower averageseasonal maximum temperatures (r2 = 0.85,p = 0.025). These results signify that maximumand minimum temperatures are the majorparameters that influence the onset andduration of the Pinus pollen season inthe environs of Brisbane. Respiratory allergyis an important health issue in Brisbane,Australia, but it remains unknown whether ornot airborne Pinus pollen is acontributing factor.

SubCM: A tool for improved visibility of software change in an industrial setting

Software Configuration Management is the discipline of managing large collections of software development artefacts from which software products are built. Software configuration management tools typically deal with artefacts at fine levels of granularity - such as individual source code files - and assist with coordination of changes to such artefacts. This paper describes a lightweight tool, designed to be used on top of a traditional file-based configuration management system. The add-on tool support enables users to flexibly define new hierarchical views of product structure, independent of the underlying artefact-repository structure. The tool extracts configuration and change data with respect to the user-defined hierarchy, leading to improved visibility of how individual subsystems have changed. The approach yields a range of new capabilities for build managers, and verification and validation teams. The paper includes a description of our experience using the tool in an organization that builds large embedded software systems.

Effect of modified atmosphere packaging on the quality of minimally processed pineapple cv.'Smooth Cayenne' fruit

The effects of modified atmosphere (MA) conditions on the quality of minimally processed pineapple slices were determined. Commercial pineapple slice packs sealed with 40 pm thick polyester film were kept at 4.5 degrees C for 14 d. The oxygen transmission rate of the film was 23 ml m(-2) day(-1) atm(-1) (at 25 degrees C, 75% RH). In-built atmospheres and the quality of the products were determined. O-2 concentrations within the packs stabilised at 2%, while CO2 concentrations increased to 70% by day 14. The high CO2 level suggested an inappropriate lidding film permeability for the product, and hence affected its quality. Three batches of pineapple slices were packed in the laboratory using lidding films with oxygen transmission rate of 75, 2790 or 5000 ml m(-2) day(-1) atm(-1) (at 23 degrees C, 0% RH). Headspace atmospheres from laboratory-packed pineapple slices suggested an optimum equilibrium modified atmosphere of ca. 2% O-2 and 15% CO2. Respiration data from the laboratory-prepared packs were pooled together and used to develop a correlation model relating respiration rates to O-2 and CO2 concentrations. The model showed a decrease in respiration rate with decreasing O-2 and increasing CO2 concentrations. Respiration rate stabilised at 2% 02 and 10% CO2. The high concentrations of CO2 observed in the commercial packs did not fit the range in the respiration model. The model could aid in selection of MA conditions for minimally processed pineapple fruit.

The effect of the atmosphere and the role of pore filling on the sintering of aluminium

Alloys of Al-3.8Cu-1Mg-0.7Si, Al-4Cu-0.6Si-0.1Mg, Al-4Cu-1.2Mg and Al-1.9Mg-1.9Si were made using air atomised powder and conventional press-and-sinter powder metallurgy techniques. These were sintered under nitrogen with a controlled water content which varied from 3 to 630 ppm (a dew point of -69 to -25 degrees C), nitrogen-5%hydrogen, argon and argon-5% hydrogen, all at atmospheric pressure, or a vacuum of

Diagnostics of A Range of Highly Superorbital Carbon Dioxide Flows

Expansion tubes are impulse facilities capable of generating highly energetic hyper-sonic flows. This work surveys a broad range of flow conditions produced in the facility X1 with carbon dioxide test gas, for simulation of spacecraft entry into the Martian atmosphere. Conditions with nominal flow speeds of 7, 9, 11 and 13 km/s were tested. The freestream conditions were calibrated using static/Pitot pressure measurements and advanced optical diagnostics. An extensive set of holographic interferometry experiments was performed on flows over wedges for quantitative study of freestream and post-shock densities, and post-shock ionisation. A one-dimensional code with frozen and equilibrium chemistry capabilities was used to estimate the freestream conditions. An equilibrium chemistry model produced a good match to measured freestream quantities at the high enthalpy conditions which are a major aim of this facility's operation. The freestream in the lower enthalpy conditions was found to be heavily influenced by chemical non-equilibrium. Non-equilibrium in the final unsteady expansion process of flow generation was accounted for by switching from equilibrium to frozen chemistry at a predetermined point. Comparison between the freestream density results of holographic interferometry, pressure measurements and computations shows good agreement.

Embedded Voxel Colouring

The reconstruction of a complex scene from multiple images is a fundamental problem in the field of computer vision. Volumetric methods have proven to be a strong alternative to traditional correspondence-based methods due to their flexible visibility models. In this paper we analyse existing methods for volumetric reconstruction and identify three key properties of voxel colouring algorithms: a water-tight surface model, a monotonic carving order, and causality. We present a new Voxel Colouring algorithm which embeds all reconstructions of a scene into a single output. While modelling exact visibility for arbitrary camera locations, Embedded Voxel Colouring removes the need for a priori threshold selection present in previous work. An efficient implementation is given along with results demonstrating the advantages of posteriori threshold selection.

Oxidation mechanism of Si3N4-bonded SiC ceramics by CO, CO2 and steam

This paper presents a theoretical and experimental investigation into the oxidation reactions of Si3N4-bonded SiC ceramics. Such ceramics which contain a small amount of silicon offer increased oxidation and wear resistance and are widely used as lining refractories in blast furnaces. The thermodynamics of oxidation reactions were studied using the JANAF tables. The weight gain was measured using a thermogravimetric analysis technique to study the kinetics. The temperature range of oxidation measurements is from 1073 to 1573 K and the oxidation atmosphere is water vapour, pure CO and CO-CO2 gas mixtures with various CO-to-CO2 ratios. Thermodynamic simulations showed that the oxidation mechanism of Si3N4-bonded SiC ceramics is passive oxidation and all components contribute to the formation of a silica film. The activated energies of the reactions follow the sequence Si3N4>SiC>Si. The kinetic study revealed that the oxidation of Si3N4-bonded SiC ceramics occurred in a mixed regime controlled by both interface reaction and diffusion through the silica film. Under the atmosphere conditions prevailing in the blast furnace, this ceramic is predicted to be passively oxidized with the chemical reaction rate becoming more dominant as the CO concentration increases. (C) 1998 Chapman & Hall.