Freeform fabrication of aluminum metal-matrix composites

A series of metal-matrix composites were formed by extrusion freeform, fabrication of a sinterable aluminum alloy in combination with silicon carbide particles and whiskers, carbon fibers, alumina particles, and hollow flyash cenospheres. Silicon carbide particles were most successful in that the composites retained high density with up to 20 vol% of reinforcement and the strength approximately doubles over the strength of the metal matrix alone. Comparison with simple models suggests that this unexpectedly high degree of reinforcement can be attributed to the concentration of small silicon carbide particles around the larger metal powder. This fabrication method also allows composites to be formed with hollow spheres that cannot be formed by other powder or melt methods.

The effect of trace elements on the sintering of an Al-Zn-Mg-Cu alloy

Trace elements can have a significant effect on the processing and properties of aluminium alloys, including sintered alloys. As little as 0.07 wt% (100 ppm) lead, tin or indium promotes sintering in an Al-Zn-Mg-Cu alloy produced from mixed elemental powders. This is a liquid phase sintering system and thin liquid films form uniformly throughout the alloy in the presence of the trace elements, but liquid pools develop in their absence. Analytical transmission electron microscopy indicates that the trace elements are confined to the interparticle and grain boundary regions. The sintering enhancement is attributed to the segregation of the microalloying addition to the liquid-vapour interface. Because the microalloying elements have a low surface tension, they lower the effective surface tension of the liquid. This reduces the wetting angle and extends the spreading of the liquid through the matrix. An improvement in sintering results. (C) 2001 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Cold worked Cu-Fe-Cr alloys

The aim of this project was to investigate the properties of copper rich Cu-Fe-Cr alloys for the purpose of developing a new cost effective, high-strength, high-conductivity copper alloy. This paper reports on the influence of cold work. The age hardening response of the Cu-0.7%Cr-2.0%Fe alloy was minimal, but the resistance to softening was superior to that reported for any commercial high-strength, high-conductivity (HSHC) copper alloy with comparable mechanical and electrical properties. For example, an excess of 85% of the original hardness of the 40% cold worked alloy is retained after holding at 700 degreesC for 1 hour, whereas commercial HSHC Cu-Fe-P alloys have been reported to soften significantly after 1 hours exposure at less than 500 degreesC. The Cu-0.7Cr-2.0Fe alloy would therefore be expected to be more suitable for applications with a significant risk of exposure to elevated temperatures. Optical microscope examination of cold worked and aged microstructures confirmed the high resistance to recrystallization for Cu-0.7%Cr-2.0%Fe. The Zener-Smith drag term, predicting the pinning effect of second phase particles on dislocations in cold worked microstructures, was calculated using the precipitate characteristics obtained from TEM, WDS and resistivity measurements. The pinning effect of the precipitate dispersions in the peak-aged condition was determined to be essentially equivalent for the Cu-0.7%Cr-0.3%Fe and Cu-0.7%Cr-2.0%Fe alloys. A lower recrystallisation temperature in the Cu-0.7%Cr-0.3%Fe alloy was therefore attributed to faster coarsening kinetics of the secondary precipitates resulting from a higher Cr concentration in the precipitates at lower iron content. (C) 2001 Kluwer Academic Publishers.

Using postoperative cardiac troponin-I (cTi) levels to detect myocardial ischaemia in patients undergoing vascular surgery

Background, Cardiac complications occur commonly in vascular surgery patients. Diagnosis of cardiac complications is difficult because of the inaccuracies associated with traditional cardiac enzyme measurements. CTi, a highly sensitive and specific marker of myocardial injury, may be able to detect cardiac complications with greater ease and accuracy. Methods. The study prospectively examined 100 consecutive patients who underwent major vascular surgery between 6/7/98 and 31/12/98 at the Royal Brisbane Hospital. Daily measurements of cTi, creatine kinase (CK), creatine kinase MB (CKMB), CKMB index, renal function and haemoglobin were taken for three postoperative days. One postoperative electrocardiograph (ECC) was taken. An extensive cardiac history was taken. Intraoperative and postoperative events were recorded. Findings. There were 100 patients, 18 patients (18%) had a cTi elevation. On the basis of classical diagnostic criteria, 15 patients (15%) suffered one or more cardiac complication (either myocardial infarction, congestive cardiac failure, unstable angina or atrial fibrillation), One patient (1%) who had a cTi elevation died. CTI elevation occurred in five patients (5%) who were not diagnosed with cardiac complications based on traditional criteria. Despite not meeting specific diagnostic criteria for cardiac complications, all patients showed signs and symptoms that could be attributed to myocardial ischaemia, Every patient who developed congestive cardiac failure or atrial fibrillation had a cTi elevation. A Chi-square analysis revealed a significant association between cTi elevation and postoperative cardiac complications. Four variables contributed small but significant amounts of unique variance to the prediction of peak cTi on linear regression analysis. These were peak CKMB index, postoperative congestive cardiac failure, postoperative chest pain and postoperative cardiac complications. Conclusions. Routine cTi monitoring of postoperative vascular patients would be an effective and inexpensive way to detect patients with cardiac complications. The relationship between postoperative cTi elevation and significant coronary artery disease remains to be shown, (C) 2001 The international Society for Cardiovascular Surgery. Published by Elsevier Science Ltd. All rights reserved.

How different is Mediterranean Caulerpa taxifolia (Caulerpales : Chlorophyta) to other populations of the species?

The green macroalgal species Caulerpa taxifolia is indigenous to tropical/subtropical Australia, ranging as far south as 28degrees and 29degrees 15' S on the Australian mainland east and west coasts, respectively. The origin of disjunct populations of the species, discovered in 2000 on the Australian mainland east coast at localities to 35degrees S remains unknown, variously attributed to introduced exotic strains or range extensions from other eastern Australian populations. Some naturally occurring Australian populations of C. taxifolia are similar to Mediterranean C. taxifolia. In Australia, large broad forms of the species, which have been known in the region since 1860, grow luxuriantly in sheltered seagrass meadows, with some of these populations tolerating minimum surface seawater temperatures in winter of 12.5 to 14.5degreesC. Accordingly, the contention that the Mediterranean has been invaded by a genetically-modified, large, cold-adapted strain of C. taxifolia may be incorrect. It is crucial that genetic markers (DNA fingerprinting, microsatellites) sensitive at the population level are used to accurately determine the genetic relatedness of C. taxifolia populations.

Mobile digital technology: Emerging issues for marketing

The growth of direct marketing has been attributed to rapid advances in technology and the changing market context. The fundamental ability of direct marketers to communicate with consumers and to elicit a response, combined with the ubiquitous nature and power of mobile digital technology, provides a synergy that will increase the potential for the success of direct marketing. The aim of this paper is to provide an analytical framework identifying the developments in the digital environment from e-marketing to m-marketing, and to alert direct marketers to the enhanced capabilities available to them.

Overcrowding and Infant Mortality: A Tale of Two Cities

Using detailed historical data for the cities of Glasgow and Edinhurgh, evidence is found in support of the hypothesis that overcrowding is a significant cause of infant mortality. We distinguish between voluntary overcrowding (due to the budgetary choices of poor families) and involuntary overcrowding (due to market failure in the provision of an adequate supply of appropriate housing). We found that, over the fifty year period, 1911-1961, Glasgow's infant mortality rate was significantly higher than that of Edinburgh, despite their close geographical proximity, and that a large part of the difference can he attributed to involuntary overcrowding in the first half of the twentieth century. We argue that this was due to the distinctly different housing policies adopted by the two cities, with important lessons for present day public authorities.

Capacity utilisation and profitability: A decomposition of short-run profit efficiency

The principal aim of this paper is to measure the amount by which the profit of a multi-input, multi-output firm deviates from maximum short-run profit, and then to decompose this profit gap into components that are of practical use to managers. In particular, our interest is in the measurement of the contribution of unused capacity, along with measures of technical inefficiency, and allocative inefficiency, in this profit gap. We survey existing definitions of capacity and, after discussing their shortcomings, we propose a new ray economic capacity measure that involves short-run profit maximisation, with the output mix held constant. We go on to describe how the gap between observed profit and maximum profit can be calculated and decomposed using linear programming methods. The paper concludes with an empirical illustration, involving data on 28 international airline companies. The empirical results indicate that these airline companies achieve profit levels which are on average US$815m below potential levels, and that 70% of the gap may be attributed to unused capacity. (C) 2002 Elsevier Science B.V. All rights reserved.

Genetic and environmental contributions to cannabis dependence in a national young adult twin sample

Background. This paper examines genetic and environmental contributions to risk of cannabis dependence. Method. Symptoms of cannabis dependence and measures of social, family and individual risk factors were assessed in a sample of 6265 young adult male and female Australian twins born 1964-1971. Results. Symptoms of cannabis dependence were common: 11(.)0% of sample (15(.)1% of men and 7(.)8% of women) reported two or more symptoms of dependence. Correlates of cannabis dependence included educational attainment, exposure to parental conflict, sexual abuse, major depression, social anxiety and childhood conduct disorder. However, even after control for the effects of these factors, there was evidence of significant genetic effects on risk of cannabis dependence. Standard genetic modelling indicated that 44(.)7% (95% CI = 15-72(.)2) of the variance in liability to cannabis dependence could be accounted for by genetic factors, 20(.)1% (95 CI = 0-43(.)6) could be attributed to shared environment factors and 35(.)3% (95% CI = 26(.)4-45(.)7) could be attributed to non-shared environmental factors. However, while there was no evidence of significant gender differences in the magnitude of genetic and environmental influences, a model which assumed both genetic and shared environmental influences on risks of cannabis dependence among men and shared environmental but no genetic influences among women provided an equally good fit to the data. Conclusions. There was consistent evidence that genetic risk factors are important determinants of risk of cannabis dependence among men. However, it remains uncertain whether there are genetic influences on liability to cannabis dependence among women.

Economics teaching in Australian universities: Rewards and outcomes

This paper presents evidence from two survey's to help explain the poor ratings consistently given to the teaching of economics at Australian universities. The evidence suggests that the Poor ratings of economics teaching can be attributed to two related factors: inappropriate pedagogical practices and lack of rewards for allocating additional time to teaching. The survey data oil pedagogy, in economics consist of 205 responses from graduates from two Queensland universities. The time elapsed since graduation ranges from 1 to 10 years. The survey data on academics' time allocation consist of 290 responses from academic economists across a wide range of Australian universities.

Diving behaviour of two Australian bimodally respiring turtles, Rheodytes leukops and Emydura macquarii, in a natural setting

Time-depth recorders were used to investigate the diving performance and behaviour of two bimodally respiring turtle species, Rheodytes leukops and Emydura niacquarii, known to have a high and low reliance on aquatic respiration, respectively. Significant differences in diving performance between R. leukops and E. macquarii were observed in the number of dives/day (39.3 +/- 5.38 vs 112.2 +/- 11.73 dives/day; mean +/- SE), mean dive length (33.1 +/- 7.33 min vs 9.6 +/- 2.26 min) and maximum dive length (623 +/- 104.74 min vs 67.1 +/- 8.14 min), respectively. Differences in diving performance between R. leukops and E macquarii are attributed to the species' reliance (or lack thereof) upon aquatic respiration. Rheodytes leukops displayed a weak bimodal pattern of increased surfacing frequency in the early morning (05:00-07:00) and late afternoon (14:00-18:00), while E. macquarii displayed a strong bimodal pattern of elevated surfacing frequency over similar time periods. Daily patterns of increased surfacing frequency for both species failed to correlate with fluctuating aquatic Po-2 levels or water temperature, and may instead be explained by the heightened activity levels of both species during twilight.

Cleaner fish Labroides dimidiatus recognise familiar clients

Individual recognition has been attributed a crucial role in the evolution of complex social systems such as helping behaviour and cooperation. A classical example for interspecific cooperation is the mutualism between the cleaner fish Labroides dimidiatus and its client reef fish species. For stable cooperation to evolve, it is generally assumed that partners interact repeatedly and remember each other's past behaviour. Repeated interactions may be achieved by site fidelity or individual recognition. However, as some cleaner fish have more than 2,300 interactions per day with various individuals per species and various species of clients, basic assumptions of cooperation theory might be violated in this mutualism. We tested the cleaner L. dimidiatus and its herbivorous client, the surgeon fish Ctenochaetus striatus, for their ability to distinguish between a familiar and an unfamiliar partner in a choice experiment. Under natural conditions, cleaners and clients have to build up their relationship, which is probably costly for both. We therefore predicted that both clients and cleaners should prefer the familiar partner in our choice experiment. We found that cleaners spent significantly more time near the familiar than the unfamiliar clients in the first 2 minutes of the experiment. This indicates the ability for individual recognition in cleaners. In contrast, the client C. striatus showed no significant preference. This could be due to a sampling artefact, possibly due to a lack of sufficient motivation. Alternatively, clients may not need to recognise their cleaners but instead remember the defined territories of L. dimidiatus to achieve repeated interactions with the same individual.

Transpecific microsatellites for hard pines M. Shepherd, M. Cross, T. Maguire, M. Dieters, C. Williams, R. Henry

Microsatellites are difficult to recover from large plant genomes so cross-specific utilisation is an important source of markers. Fifty micro satellites were tested for cross-specific amplification and polymorphism to two New World hard pine species, slash pine (Pinus elliottii var. elliottii) and Caribbean pine (R caribaea var. hondurensis). Twenty-nine (58%) markers amplified in both hard pine species, and 23 of these 29 were polymorphic. Soft pine (subgenus Strobus) microsatellite markers did amplify, but none were polymorphic. Pinus elliottii var. elliottii and R caribaea var. hondurensis showed mutational changes in the flanking regions and the repeat motif that were informative for Pinus spp. phylogenetic relationships. Most allele length variation could be attributed to variability in repeat unit number. There was no evidence for ascertainment bias.

Reversible luminescence thermochromism in dipotassiumsodium tris[dicyanoargentate(I)] and the role of structural phase transitions

As a function of temperature, the layered compound K2Na[Ag(CN)213 displays dramatic variations in luminescence thermochromism with major trend changes occurring around 80 K. In order to understand these interesting optical properties, high-resolution neutron diffraction investigations were performed on a polycrystalline sample of this material in the temperature range from 1.5 to 300 K, and previous synchrotron X-ray data of Larochelle et al. (Solid State Commun. 114, 155 (2000)) were reinterpreted. The corresponding significant structural changes were found to be continuous with an anomalous increase of the monoclinic c-lattice parameter with decreasing temperature, associated with slight reorientations of two inequivalent, approximately linear N-C-Ag-C-N units. In the whole temperature range, the crystal structure is monoclinic with the space group C2/m. Based on the structural results, the major luminescence thermochromism changes around 80 K are attributed to the dominance of a back energy transfer process from low- to high-energy excitons at high temperatures. (E) 2002 Elsevier Science (USA).

History and nomenclature of the theropod dinosaur tracks Bueckeburgichnus and Megalosauripus

The most recent account of Bueckeburgichnus maximus Kuhn 1958, a distinctive theropod dinosaur track from the Lower Cretaceous of Germany, is shown to be based on a referred specimen mistakenly identified as the holotype and the correct name of this taxon is deemed to be Megalosauripus maximus (Kuhn 1958). This minor revision has important consequences for nomenclature of the many European, Asian, North American and Australian dinosaur tracks attributed to megalosaurian theropods. Many of those tracks were named Megalosauripus, but that name has a confusing multiplicity of meanings and it should be restricted to the highly characteristic dinosaur track formerly identified as Bueckeburgichnus. Other tracks named "Megalosauripus”; (in its several other senses) will require new nomenclature, despite their extensive and repeated revision since 1996. It is recommended that future revision should adopt conventions of the International Code of Zoological Nomenclature. Although previous revisions expressed an intention to adhere to those conventions, these were not put into practice, with the unfortunate result of multiplying the problems that surround the nomenclature of megalosaur tracks. Introduction of the name Megalosauripus maximus (Kuhn 1958) eliminates those burgeoning problems and permits the introduction of new and objective nomenclature for presumed megalosaur tracks.