Quantifying stresses and support requirements in the undercut and production level drifts of block and panel caving mines

A numerical modelling strategy has been developed in order to quantify the magnitude of induced stresses at the boundaries of production level and undercut level drifts for various in situ stress environments and undercut scenarios. The results of the stress modelling were in line with qualitative experiential guidelines and a limited number of induced stress measurements documented from caving sites. A number of stress charts were developed which quantify the maximum boundary stresses in drift roofs for varying in situ stress regimes, depths and undercut scenarios. This enabled many of the experiential guidelines to be quantified and bounded. A limited number of case histories of support and support performance in cave mine drifts were compared to support recommendations using the NGI classification system, The stress charts were used to estimate the Stress Reduction Factor for this system. The back-analyses suggested that the NGI classification system might be able to give preliminary estimates of support requirements in caving mines with modifications relating to rock bolt length and the support of production level intersections. (C) 2002 Elsevier Science Ltd. All rights reserved.

A decision support system for selecting sanitation systems in developing countries

Due to the socio-economic inhomogeneity of communities in developing countries, the selection of sanitation systems is a complex task. To assist planners and communities in assessing the suitability of alternatives, the decision support system SANEX™ was developed. SANEX™ evaluates alternatives in two steps. First, Conjunctive Elimination, based on 20 mainly technical criteria, is used to screen feasible alternatives. Subsequently, a model derived from Multiattribute Utility Technique (MAUT) uses technical, socio-cultural and institutional criteria to compare the remaining alternatives with regard to their implementability and sustainability. This paper presents the SANEX™ algorithm, examples of its application in practice, and results obtained from field testing.

Partitioned Bremer support and multiple trees

Partitioned Bremer support (PBS) is a valuable means of assessing congruence in combined data sets, but some aspects require clarification. When more than one equally parsimonious tree is found during the constrained search for trees lacking the node of interest, averaging PBS for each data set across these trees can conceal conflict, and PBS should ideally be examined for each constrained tree. Similarly, when multiple most parsimonious trees (MPTs) are generated during analysis of the combined data, PBS is usually calculated on the consensus tree. However, extra information can be obtained if PBS is calculated on each of the MPTs or even suboptimal trees. (C) 2002 The Willi Hennig Society. Published by Elsevier Science (USA). All rights reserved.

Improving attitude-behavior correspondence through exposure to normative support from a salient ingroup

Two experiments were conducted to test predictions derived from social identity/self-categorization theory concerning the role of group norms in attitude-behavior consistency. In Experiment 1, 160 students who could be classified as having a more or less certain target attitude were exposed to attitude congruent versus incongruent normative support from a relevant reference group (own university) under conditions of low versus high group salience. Experiment 2 was very similar in design and methodology (N=180), but a different correlate of attitude accessibility was used (an experimental manipulation of repeated expression), the target attitude was changed, and the reference group was gender. Across the 2 experiments there was consistent support for the hypothesis that participants would behave more in accordance with their attitudes when they received normative support for, rather than opposition to, their original attitude from a relevant reference group (i.e., their ingroup, not an outgroup). There was slightly weaker support for the second hypothesis that this effect would be stronger under high-than low-salience conditions. The third hypothesis (see Fazio, 1986), that attitude certainty and repeated expression of the attitude would strengthen attitude-behavior consistency, was well supported, as was the expectation that accessibility effects would be independent of reference group norm effects on attitude-behavior consistency.

Beneficial effects of air inclusions on the performance of ethylene vinyl acetate (EVA) mouthguard material

Objective: To investigate the impact characteristics of an ethylene vinyl acetate (EVA) mouthguard material with regulated air inclusions, which included various air cell volumes and wall thickness between air cells. In particular, the aim was to identify the magnitude and direction of forces within the impacts. Method: EVA mouthguard material, A mm thick and with and without air inclusions, was impacted with a constant force impact pendulum with an energy of 4.4 J and a velocity of 3 m/s. Transmitted forces through the EVA material were measured using an accelerometer, which also allowed the determination of force direction and magnitude within the impacts. Results: Statistically significant reductions in the transmitted forces were observed with all the air inclusion materials when compared with EVA without air inclusions. Maximum transmitted force through one air inclusion material was reduced by 32%. Force rebound was eliminated in one material, and reduced second force impulses were observed in all the air inclusion materials. Conclusion: The regulated air inclusions improved the impact characteristics of the EVA mouthguard material, the material most commonly used in mouthguards world wide.

Effect of ethylene vinyl acetate (EVA) closed cell foam on transmitted forces in mouthguard material

Objectives: To compare transmitted forces through ethylene vinyl acetate (EVA) mouthguard material and the same EVA material with gas inclusions in the form of a closed cell foam. Method: EVA mouthguard materials with and without foam gas inclusions and 4 mm thick were impacted with a constant force from an impact pendulum. Various porosity levels in the foam materials were produced by 1%, 5%, and 10% by weight foaming agent. The forces transmitted through the EVA after energy absorption by the test materials were measured with a force sensor and compared. Results: Only minor non-significant differences in transmitted forces through the EVA with and without foam were shown. Conclusions: The inclusion of gas in the form of a closed cell foam in 4 mm thick EVA mouthguard materials did not improve the impact performance of the EVA mouthguard material.

Recoverable reserves and support effects when optimizing open pit mine designs

Orebody modelling, support effects and the estimation of recoverable reserves are key parts of open pit optimization studies. A case study is presented on the estimation of recoverable reserves using an implementation of indicator kriging where metal quantity is used to select cutoffs, and support corrections founded on a conditional simulation approach. Mining selectivity is explored in the subsequent optimization study to compare results from indicator kriging of grade estimates on a regular size blocks and indicator kriging estimates on small size blocks. The use of indicator kriging models adjusted for a given selectivity and the use of grade proportions in each block for the optimization study, provide a presentation of the expected ore recovery for a predefined level of selectivity. The case study shows that indicator kriging estimation with full accounting of block grade distributions generates substantially better results in the pit optimization study. In addition, the adverse effects of small blocks and over-smoothing on optimization results are illustrated.