Design, modelling and analysis of a six component force balance for hypervelocity wind tunnel testing

A combination of modelling and analysis techniques was used to design a six component force balance. The balance was designed specifically for the measurement of impulsive aerodynamic forces and moments characteristic of hypervelocity shock tunnel testing using the stress wave force measurement technique. Aerodynamic modelling was used to estimate the magnitude and distribution of forces and finite element modelling to determine the mechanical response of proposed balance designs. Simulation of balance performance was based on aerodynamic loads and mechanical responses using convolution techniques. Deconvolution was then used to assess balance performance and to guide further design modifications leading to the final balance design. (C) 2001 Elsevier Science Ltd. All rights reserved.

Three-dimensional orthotropic viscoelastic finite element model of a human ligament

Ligaments undergo finite strain displaying hyperelastic behaviour as the initially tangled fibrils present straighten out, combined with viscoelastic behaviour (strain rate sensitivity). In the present study the anterior cruciate ligament of the human knee joint is modelled in three dimensions to gain an understanding of the stress distribution over the ligament due to motion imposed on the ends, determined from experimental studies. A three dimensional, finite strain material model of ligaments has recently been proposed by Pioletti in Ref. [2]. It is attractive as it separates out elastic stress from that due to the present strain rate and that due to the past history of deformation. However, it treats the ligament as isotropic and incompressible. While the second assumption is reasonable, the first is clearly untrue. In the present study an alternative model of the elastic behaviour due to Bonet and Burton (Ref. [4]) is generalized. Bonet and Burton consider finite strain with constant modulii for the fibres and for the matrix of a transversely isotropic composite. In the present work, the fibre modulus is first made to increase exponentially from zero with an invariant that provides a measure of the stretch in the fibre direction. At 12% strain in the fibre direction, a new reference state is then adopted, after which the material modulus is made constant, as in Bonet and Burton's model. The strain rate dependence can be added, either using Pioletti's isotropic approximation, or by making the effect depend on the strain rate in the fibre direction only. A solid model of a ligament is constructed, based on experimentally measured sections, and the deformation predicted using explicit integration in time. This approach simplifies the coding of the material model, but has a limitation due to the detrimental effect on stability of integration of the substantial damping implied by the nonlinear dependence of stress on strain rate. At present, an artificially high density is being used to provide stability, while the dynamics are being removed from the solution using artificial viscosity. The result is a quasi-static solution incorporating the effect of strain rate. Alternate approaches to material modelling and integration are discussed, that may result in a better model.

Novel colloidal materials for high-throughput screening applications in drug discovery and genomics

Tracking the reaction history is the means of choice to identify bioactive compounds in large combinatorial libraries. The authors describe two approaches to synthesis on silica beads: a) addition of a reporter dye tag during each synthesis step (see Figure), which attaches itself to the bead by colloidal forces, and b) encapsulating arrays of fluorescent dyes into the beads to encode them uniquely, for recognition with a flow cytometer after each reaction step.

Individual and societal bases of national identity - A comparative multi-level analysis

In a previous study (Jones and Smith, 1999) we established that much the same core pattern of national identity characterizes many developed countries. Using the national identity module from the 1995 International Social Survey Programme, we identified two dimensions of national identity: an ascriptive dimension resembling the concept of ethnic identity described in the historical and theoretical literature, and a voluntarist dimension closer to the notion of civic identity. Some writers view these dimensions in terms of a historical sequence but we find that both constructs coexist in the minds of individual respondents in the nations we examine (we exclude Bulgaria and the Philippines from the present but not the earlier analysis). The dataset used for the multilevel analyses reported here consists of 28 589 respondents in the remaining 21 countries included in the national identity database for the 1995 round of surveys. The macrosociological literature on national identity does not offer well-defined predictions about what precise patterns of national identification we might expect to find among the masses of the developed countries. There are, however, recurring themes from which one can construct plausible hypotheses about how countries might differ according to their level of development, broadly conceived. Thus, we hypothesize that forces such as post-industrialism and globalization tend to favour the more open voluntaristic form of national identity over the more restrictive ascribed form. We develop different multi-level models in order to evaluate specific hypotheses pertaining to such issues, by simultaneously relating individual and societal characteristics to the relative strength of individual commitment to these different types of national identity.

The K5 gamble: National defence and nation building under the People's Republic of Kampuchea

The K5 Plan for the defence of the Cambodian-Thai border was the response of the People's Republic of Kampuchea and its Vietnamese mentors to the threat posed by the resistance forces, particularly the Khmer Rouge, to its efforts to rebuild the nation and consolidate its administration. The very real defence gains, however, were made at the cost of bitter popular resentment over the way those gains were made.

Mark-recapture may reveal more about ecology than about population trends: Demography of a threatened ghost bat (Macroderma gigas) population

Since European settlement in Australia, the geographical range of ghost bats (Macroderma gigas) has contracted northwards. Ghost bats are thought to occur in disjunct populations with little interpopulation migration, raising concerns over the current status and future viability of the southernmost colony, which has also been threatened by mining activity. To address these concerns, demographic parameters of the southernmost colony were estimated from a mark-recapture study conducted during 1975-1981. Female bats gave birth to a single young in late spring, but only 40% (22-70%, 95% CI) of females bred in their second year, increasing to 93% (87-97%, 95% CI) for females greater than or equal to 2 years old. Sixty-five percent of juveniles caught were female. Annual adult survival ranged between 0.57-0.77 for females and 0.43-0.66 for males, and was lowest over winter-spring and greatest in autumn-winter. Juvenile survival for the first year ranged between 0.35-0.46 for females and 0.29-0.42 for males. Adult survival varied among seasons, was negatively associated with rainfall, but was not associated with temperature beyond being lower in late winter. Poor survival may result from the inferior daytime roosts that bats must use if water seepage forces them to leave their normal roosts. Although these age-specific rates of fecundity and survival suggested a declining population, mark-recapture estimates of the population trend indicated stability over the study period. Counts at daytime roosts also suggested a population decline, but were considered unreliable because of an increasing tendency of bats to avoid detection. It is therefore likely that some assumptions in estimating survival were violated. These results provide a caution against the uncritical use of population projections derived from mark-recapture estimates of demographic parameters, and the use of untested indices as the basis for conservation decisions.

A flexible method for rapid force computation in elliptical magnets

The design of open-access elliptical cross-section magnet systems has recently come under consideration. Obtaining values for the forces generated within these unusual magnets is important to progress the designs towards feasible instruments. This paper presents a novel and flexible method for the rapid computation of forces within elliptical magnets. The method is demonstrated by the analysis of a clinical magnetic resonance imaging magnet of elliptical cross-section and open design. The analysis reveals the non-symmetric nature of the generated Maxwell forces, which are an important consideration, particularly in the design of superconducting systems.

The stochastic design of force-minimized compact magnets for high-field magnetic resonance imaging applications

New designs for force-minimized compact high-field clinical MRI magnets are described. The design method is a modified simulated annealing (SA) procedure which includes Maxwell forces in the error function to be minimized. This permits an automated force reduction in the magnet designs while controlling the overall dimensions of the system. As SA optimization requires many iterations to achieve a final design, it is important that each iteration in the procedure is rapid. We have therefore developed a rapid force calculation algorithm. Novel designs for short 3- and 4-T clinical MRI systems are presented in which force reduction has been invoked. The final designs provide large homogeneous regions and reduced stray fields in remarkable short magnets. A shielded 4-T design that is approximately 30% shorter than current designs is presented. This novel magnet generates a full 50-cm diameter homogeneous region.

Experimental investigation of liquid flow shift due to gas cross flow in non-wetted packed beds

An experimental study has been carried out for the gas-liquid two-phase flow in a packed bed simulating conditions of the gas and liquid flows in the lower part of blast furnace. The localised liquid flow phenomenon in presence of gas cross flow, which usually occurs around the cohesive zone and raceway in blast furnace, was investigated in detail. Such liquid flow is characterised in terms of liquid shift distance or liquid shift angle that can effectively be measured by the experiments involved in the current study. It is found that liquid shift angle does not significantly increase or decrease with different packing depth. This finding supports the hypothesis of the force balance model where a vectorial relationship among acting forces, i.e. gas drag force, gravitational force and solid-liquid friction force, and liquid shift angle does exist. Liquid shift angle is inversely proportional to particle size and liquid density, and proportional to square of gas superficial velocity, but is almost independent on liquid flowrate and liquid viscosity. The gas-liquid drag coefficient, an important aspect for quantifying the interaction between gas and liquid flows, was conceptually modified based on the discrete feature of liquid flow through a packed bed and evaluated by the combined theoretical and experimental investigation. Experimental measurements suggest that the gas-liquid drag coefficient is approximately a constant (C-DG(')=5.4+/-1.0) and is independent on liquid properties, gas velocity and packing structure. The result shows a good agreement with previous experimental data and prediction of the existing liquid flow model.

EVA mouthguards: how thick should they be?

A major consideration in the performance of mouthguards is their ability to absorb energy and reduce transmitted forces when impacted. This is especially important to participants in contact sports such as hockey or football. The thickness of mouthguard materials is directly related to energy absorption and inversely related to transmitted forces when impacted. However, wearer comfort is also an important factor in their use. Thicker mouthguards are not user-friendly. While thickness of material over incisal edges and cusps of teeth is critical, just how thick should a mouthguard be and especially in these two areas? Transmitted forces through different thicknesses of the most commonly used mouthguard material, ethylene vinyl acetate (EVA) (Shore A Hardness of 80) were compared when impacted with identical forces which were capable of damaging the oro-facial complex. The constant impact force used in the tests was produced by a pendulum and had an energy of 4.4 joules and a velocity of 3 meters per second. Improvements in energy absorption and reductions in transmitted forces were observed with increasing thickness. However, these improvements lessened when the mouthguard material thickness was greater than 4 mm. The results show that the optimal thickness for EVA mouthguard material with a Shore A Hardness of 80 is around 4 mm. Increased thickness, while improving performance marginally, results in less wearer comfort and acceptance.

Limits to squeezing in the degenerate optical parametric oscillator

We develop a systematic theory of quantum fluctuations in the driven optical parametric oscillator, including the region near threshold. This allows us to treat the limits imposed by nonlinearities to quantum squeezing and noise reduction in this nonequilibrium quantum phase transition. In particular, we compute the squeezing spectrum near threshold and calculate the optimum value. We find that the optimal noise reduction occurs at different driving fields, depending on the ratio of damping rates. The largest spectral noise reductions are predicted to occur with a very high-Q second-harmonic cavity. Our analytic results agree well with stochastic numerical simulations. We also compare the results obtained in the positive-P representation, as a fully quantum-mechanical calculation, with the truncated Wigner phase-space equation, also known as the semiclassical theory.

The damped and coherently-driven Jaynes-Cummings model

We investigate the influence of a single-mode cavity on the Autler-Townes doublet that arises when a three-level atom is strongly driven by a laser field tuned to one of the atomic transitions and probed by a tunable, weak field coupled to the other transition. We assume that the cavity mode is coupled to the driven transition and the cavity and laser frequencies are equal to the atomic transition frequency. We find that the Autler-Townes spectrum can have one, two or three peaks depending on the relative magnitudes of the Rabi frequencies of the cavity and driving fields. We show that, in order to understand the three-peaked spectrum, it is necessary to go beyond the secular approximation, leading to interesting quantum interference effects. We find that the positions and relative intensities of the three spectral components are affected strongly by the atom-cavity coupling strength g and the cavity damping K. For an increasing g and/or decreasing K the triplet evolves into a single peak. This results in 'undressing' of the system such that the atom collapses into its ground state. We interpret the spectral features in terms of the semiclassical dressed-atom model, and also provide complementary views of the cavity effects in terms of quantum Langevin equations and the fully quantized, 'double -dressing' model.

Experimental evidence that partner choice is a driving force in the payoff distribution among cooperators or mutualists: the cleaner fish case

Supply and demand largely determine the price of goods on human markets. It has been proposed that in animals, similar forces influence the payoff distribution between trading partners in Sexual selection, intraspecific cooperation and interspecific mutualism. Here we present the first experimental evidence supporting biological market theory in it study on cleaner fish, Labroides dimidiatus. Cleaners interact with two classes of clients: choosy client species with access to several cleaners usually do not queue for service and do not return if ignored, while resident client species with access to only one cleaning station do queue or return. We used plexiglas plates with equal amounts of food to stimulate these behaviours of the two client classes. Cleaners soon inspected 'choosy' plates before 'resident' plates. This supports previous field observations that suggest that client species with access to several cleaners exert choice to receive better(immediate) service.

The nexus of value chain integration and e-business applications on public sector agriculture R&D management

We examine the potential impact of interconnectivity of value chain partnerships through electronic means (e-business practices) on the management of Public Sector Agriculture R&D in Australia. We review the changing forms of managing research and development, the forces driving these changes, and R&D processes that are theoretically consistent with the move towards value chain involvement and the increase in active constituents in Public Sector Agriculture R&D. We then explore the potential of emerging e-business models to change the patterns of inter-connectivity, speed and omnipresence of partners in the value chain. Three e-business R&D management practices are identified that provide the prerequisite flexibility necessary to take advantage of opportunistic markets. These R&D business practices are: compressing R&D to reduce time to market, fostering co-development to enter a market at the last moment and building flexible products that allow adjustment at the last possible moment. Some fundamental reallocation of existing resources will be required to meet these markets. Implications of these e-business practices for R&D management are discussed.

Linear ketenimines. Variable structures of C,C-dicyanoketenimines and C,C-bis-sulfonylketenimines

C,C-Dicyanoketenimines 10a-c were generated by flash vacuum thermolysis of ketene NS-acetals 9a-c or by thermal or photochemical decomposition of alpha-azido-,beta-cyanocinnamonitrile 11. In the latter reaction, 3,3-dicyano-2-phenyl-1-azirine 12 is also formed. IR spectroscopy of the keteniminines isolated in Ar matrixes or as neat films, NMR spectroscopy of 10c, and theoretical calculations (B3LYP/6-31G*) demonstrate that these ketenimines have variable geometry, being essentially linear along the CCN-R framework in polar media (neat films and solution), but in the gas phase or Ar matrix they are bent, as is usual for ketenimines. Experiments and calculations agree that a single CN substituent as in 13 is not enough to enforce linearity, and sulfonyl groups are less effective that cyano groups in causing linearity. C,C-Bis(methylsulfonyl)ketenimines 4-5 and a C-cyano-C-(methylsulfonyl)ketenimine 15 are not linear. The compound p-O2NC6H4N=C= C(COOMe)2 previously reported in the literature is probably somewhat linearized along the CCNR moiety. A computational survey (B3LYP/6-31G*) of the inversion barrier at nitrogen indicates that electronegative C-substituents dramatically lower the barrier; this is also true of N-acyl substituents. Increasing polarity causes lower barriers. Although N-alkylbis(methylsulfonyl)ketenimines are not calculated to be linear, the barriers are so low that crystal lattice forces can induce planarity in N-methylbis(methylsulfonyl)ketenimine 3.