Implementação em FPGA de um Modem QPSK

Esta dissertação insere-se num conjunto de trabalhos a decorrer no Instituto de Telecomunicações de Aveiro que tem como objetivo o desenvolvimento de um sistema de comunicação para um UAV. Neste sentido, apresenta a implementação e validação de um modem em banda base aberto e flexível implementado em FPGA, baseado em abordagem SDR, com possibilidade de integraçãoo no sistema de comunicação com o UAV. Ao longo desta dissertação implementou-se, utilizando o MATLAB, um modem de modulação adaptável, ao qual foram integrados algoritmos de sincronismo e de correção de fase. Desta forma, foi possível realizar uma análise ao modelo comportamental dos vários constituintes do modem abstraindose dos tempos de atraso do processamento ou da precisão da representação dos dados, e assim simplificar a sua implementação em hardware. Analisado o modelo comportamental do modem desenvolvido em MATLAB realizou-se a sua implementação em hardware para a modulação QPSK. A sua prototipagem foi realizada, com recurso à ferramenta computacional Vivado Design Suite 2014.2, utilizando o kit de desenvolvimento ZedBoard e o frontend AD-FMCOMMS1-EBZ. O correto funcionamento dos módulos implementados em hardware foi posteriormente avaliado através de uma interface entre o MATLAB e a Zed- Board, sendo que, os resultados obtidos no modelo em MATLAB serviram como termo de comparação. Através da utilização desta interface é possível validar parte do modem implementado em FPGA, mantendo o restante processamento a ser realizado em MATLAB, validando assim os módulos em FPGA de uma forma isolada.

Operating infrastructure for an FPGA and ARM system

Advances in FPGA technology and higher processing capabilities requirements have pushed to the emerge of All Programmable Systems-on-Chip, which incorporate a hard designed processing system and a programmable logic that enable the development of specialized computer systems for a wide range of practical applications, including data and signal processing, high performance computing, embedded systems, among many others. To give place to an infrastructure that is capable of using the benefits of such a reconfigurable system, the main goal of the thesis is to implement an infrastructure composed of hardware, software and network resources, that incorporates the necessary services for the operation, management and interface of peripherals, that coompose the basic building blocks for the execution of applications. The project will be developed using a chip from the Zynq-7000 All Programmable Systems-on-Chip family.

Error correcting codes for visible light communication systems

Over the past few years, the number of wireless networks users has been increasing. Until now, Radio-Frequency (RF) used to be the dominant technology. However, the electromagnetic spectrum in these region is being saturated, demanding for alternative wireless technologies. Recently, with the growing market of LED lighting, the Visible Light Communications has been drawing attentions from the research community. First, it is an eficient device for illumination. Second, because of its easy modulation and high bandwidth. Finally, it can combine illumination and communication in the same device, in other words, it allows to implement highly eficient wireless communication systems. One of the most important aspects in a communication system is its reliability when working in noisy channels. In these scenarios, the received data can be afected by errors. In order to proper system working, it is usually employed a Channel Encoder in the system. Its function is to code the data to be transmitted in order to increase system performance. It commonly uses ECC, which appends redundant information to the original data. At the receiver side, the redundant information is used to recover the erroneous data. This dissertation presents the implementation steps of a Channel Encoder for VLC. It was consider several techniques such as Reed-Solomon and Convolutional codes, Block and Convolutional Interleaving, CRC and Puncturing. A detailed analysis of each technique characteristics was made in order to choose the most appropriate ones. Simulink models were created in order to simulate how diferent codes behave in diferent scenarios. Later, the models were implemented in a FPGA and simulations were performed. Hardware co-simulations were also implemented to faster simulation results. At the end, diferent techniques were combined to create a complete Channel Encoder capable of detect and correct random and burst errors, due to the usage of a RS(255,213) code with a Block Interleaver. Furthermore, after the decoding process, the proposed system can identify uncorrectable errors in the decoded data due to the CRC-32 algorithm.