PMMA-co-EHA cements for osteoprotheses

The main purpose of this thesis was to produce new formulations of PMMA-co- EHA and study its feasibility as being an alternative to traditional PMMA bone cements. Thus, were originally produced several co-polymers of PMMA-co-EHA and its mechanical properties and in vitro behaviour were evaluated. The copolymers were obtained by radical polymerization and several formulations were produced by partial replacement of MMA (up to about 50%) for EHA. Overall, the results suggest that the partial replacement of MMA by EHA decreased the modulus of the materials and, consequently, increased its flexibility. Then, PMMA commercial beads were added to PMMA-co-EHA formulations (to get bone cement) and the general properties of the resulting bone cements were evaluated. In general, the results revealed that the partial replacement of MMA by EHA led to beneficial changes in curing parameters (there was a reduction of the peak temperature and an increase of curing/setting time), in the in vitro behaviour (the water capacity increased) and in the mechanical properties (the bending strength increased) of new cements. The in vitro cellular response of new formulations of PMMA-co-EHA was compared with that of traditional PMMA bone cement. To this end, we tested the cell adhesion and proliferation of osteoblast-like MG63 cells and human cells from bone marrow. The results revealed that both types of cells were able to attach and proliferate in both formulations. The only exception was observed for the formulation prepared with the highest percentage of EHA, where a few cells that adhere failed to proliferate. Moreover, it was found that increasing the amount of EHA in cement led to an increasing inhibition of cell growth, especially during the first week of culture. This was related to increased water uptake capacity by the new formulations and consequent release of some of its toxic components. Finally, PMMA commercial beads were partially replaced by HA particles and the influence of this substitution on the curing parameters, the mechanical properties and in vitro behaviour of the resulting composites was also evaluated. Incorporation of HA into the bone cements induced a number of significant changes in its final properties: 1) decrease the peak temperature; 2) increase of curing time, 3) increasing the value of elastic modulus accompanied by decrease of the strength/tension. This last finding was related to poor interfacial adhesion between the various components of the bone cements and a heterogeneous distribution (possible agglomeration) of HA particles.

Nanocompósitos de PMMA/HA/grafeno para aplicações biomédicas

Os cimentos ósseos à base de PMMA para aplicações em artroplastia da anca apresentam como grande limitação o facto do seu constituinte principal ser um elemento bioinerte o que leva à falta de integração entre as interfaces cimento ósseo/tecido ósseo, comprometendo assim o desempenho mecânico da prótese ortopédica ao longo do tempo. Esta dissertação tem como objetivo principal a preparação de novas formulações de cimentos ósseos com a capacidade de estabelecer interações com os tecidos vivos circundantes. De modo a melhorar a bioatividade do sistema e facilitar a sua osseointegração, os cimentos ósseos comerciais foram reforçados com cargas significativas de HA. No entanto o recurso a elevadas cargas de HA (~60% m/m) no cimento ósseo promove debilidades do ponto de vista estrutural, levando a uma baixa resistência mecânica do material final. No sentido de ultrapassar esta limitação, foram inseridas nanoestruturas de carbono (GO ou CNTs) em baixas percentagens na matriz polimérica por forma a maximizar a sua performance mecânica através da perfeita integração de todos os componentes. A primeira fase deste trabalho consistiu no desenvolvimento de metodologias que permitissem a síntese de GO através da exfoliação química da grafite em solução aquosa. Os resultados obtidos demonstraram a obtenção de folhas de GO em larga escala e com número de camadas uniforme. A funcionalização orgânica superficial via ATRP do GO obtido, com cadeias de PMMA possibilitou o desenvolvimento de novos materiais nanocompósitos, no entanto alguns fatores de natureza tecnológica inviabilizaram o seu uso como agente de reforço na matriz idealizada. O desenvolvimento de novas formulações de cimentos ósseos consistiu numa matriz de PMMA/HA (1:2 (m/m)) reforçada com pequenas percentagens de GO ou CNTs (0,01, 0,1, 0,5 e 1,0% m/m). A síntese destes materiais nanocompósitos resultou da combinação de diversas técnicas: ultrassons, granulação por congelamento e liofilização. A análise estrutural dos nanocompósitos obtidos demonstrou a eficácia da metodologia desenvolvida na homogeneização de todos os elementos do sistema. Os estudos desenvolvidos após a conformação e caracterização estrutural dos novos materiais nanocompósitos permitiram verificar que as nanoestruturas de carbono apresentavam efeitos adversos na polimerização via radicalar do PMMA. A análise da fração orgânica permitiu verificar a presença de espécies oligoméricas o que reduziu significativamente o comportamento mecânico dos nanocompósitos. Através do estudo do aumento da concentração das espécies radicalares iniciais foi possível suplantar este problema e tirar o máximo rendimento dos agentes de reforço, tendo-se destacado os nanocompósitos reforçados com GO. A validação do ponto de vista mecânico das novas formulações de cimentos ósseos recaiu sobre o procedimento descrito na norma europeia ISO 5833 de 2002 – Implantes para cirurgia – cimentos acrílicos, tendo sido realizados os testes de compressão e de flexão. A avaliação biológica do comportamento dos cimentos ósseos assentou em duas abordagens complementares: estudos de mineralização em SBF e estudos de biocompatibilidade em meios celulares. Após a incubação das amostras em SBF ficou demonstrada a excelente capacidade para promoverem a integração de uma camada apatítica. Através de estudos celulares com Fibroblastos L929 e Osteoblastos Saos-2, nos quais foram avaliados a proliferação celular, viabilidade celular, espécies reativas de oxigénio, apoptose e morfologia celular, foi possível verificar bons níveis de biocompatibilidade para os materiais devolvidos.

Evaluation of the matabolic response of osteosarcoma cells to conventional and new anticancer drugs by NMR metabolomics

The main scope of this work was to evaluate the metabolic effects of anticancer agents (three conventional and one new) in osteosarcoma (OS) cells and osteoblasts, by measuring alterations in the metabolic profile of cells by nuclear magnetic resonance (NMR) spectroscopy metabolomics. Chapter 1 gives a theoretical framework of this work, beginning with the main metabolic characteristics that globally describe cancer as well as the families and mechanisms of action of drugs used in chemotherapy. The drugs used nowadays to treat OS are also presented, together with the Palladium(II) complex with spermine, Pd2Spm, potentially active against cancer. Then, the global strategy for cell metabolomics is explained and the state of the art of metabolomic studies that analyze the effect of anticancer agents in cells is presented. In Chapter 2, the fundamentals of the analytical techniques used in this work, namely for biological assays, NMR spectroscopy and multivariate and statistical analysis of the results are described. A detailed description of the experimental procedures adopted throughout this work is given in Chapter 3. The biological and analytical reproducibility of the metabolic profile of MG-63 cells by high resolution magic angle spinning (HRMAS) NMR is evaluated in Chapter 4. The metabolic impact of several factors (cellular integrity, spinning rate, temperature, time and acquisition parameters) on the 1H HRMAS NMR spectral profile and quality is analysed, enabling the definition of the best acquisition parameters for further experiments. The metabolic consequences of increasing number of passages in MG-63 cells as well as the duration of storage are also investigated. Chapter 5 describes the metabolic impact of drugs conventionally used in OS chemotherapy, through NMR metabolomics studies of lysed cells and aqueous extracts analysis. The results show that MG-63 cells treated with cisplatin (cDDP) undergo a strong up-regulation of lipid contents, alterations in phospholipid constituents (choline compounds) and biomarkers of DNA degradation, all associated with cell death by apoptosis. Cells exposed to doxorubicin (DOX) or methotrexate (MTX) showed much slighter metabolic changes, without any relevant alteration in lipid contents. However, metabolic changes associated with altered Krebs cycle, oxidative stress and nucleotides metabolism were detected and were tentatively interpreted at the light of the known mechanisms of action of these drugs. The metabolic impact of the exposure of MG-63 cells and osteoblasts to cDDP and the Pd2Spm complex is described in Chapter 6. Results show that, despite the ability of the two agents to bind DNA, the metabolic consequences that arise from exposure to them are distinct, namely in what concerns to variation in lipid contents (absent for Pd2Spm). Apoptosis detection assays showed that, differently from what was seen for MG-63 cells treated with cDDP, the decreased number of living cells upon exposure to Pd2Spm was not due to cell death by apoptosis or necrosis. Moreover, the latter agent induces more marked alterations in osteoblasts than in cancer cells, while the opposite seemed to occur upon cDDP exposure. Nevertheless, the results from MG-63 cells exposure to combination regimens with cDDP- or Pd2Spm-based cocktails, described in Chapter 7, revealed that, in combination, the two agents induce similar metabolic responses, arising from synergy mechanisms between the tested drugs. Finally, the main conclusions of this thesis are summarized in Chapter 8, and future perspectives in the light of this work are presented.

Development and characterization of Poly(L-lactic acid) (PLLA) platforms for bone tissue engineering

The development of scaffolds based on biomaterials is a promising strategy for Tissue Engineering and cellular regeneration. This work focuses on Bone Tissue Engineering, the aim is to develop electrically tailored biomaterials with different crystalline and electric features, and study their impacts onto cell biological behavior, so as to predict the materials output in the enhancement of bone tissue regeneration. It is accepted that bone exhibits piezoelectricity, a property that has been proved to be involved in bone growth/repair mechanism regulation. In addition electrical stimulations have been proved to influence bone growth and repair. Piezoelectric materials are therefore widely investigated for a potential use in bone tissue engineering. The main goal is the development of novel strategies to produce and employ piezoelectric biomaterials, with detailed knowledge of mechanisms involved in cell-material interaction. In the current work, poly (L-lactic) acid (PLLA), a synthetic semi-crystalline polymer, exhibiting biodegradibility, biocompatibility and piezoelectricity is studied and proposed as a promoter of enhanced tissue regeneration. PLLA has already been approved for implantation in human body by the Food and Drug Administration (FDA), and at the moment it is being used in several clinical strategies. The present study consists of first preparing films with different degrees of crystallinity and characterizing these PLLA films, in terms of surface and structural properties, and subsequently assessing the behavior of cells in terms of viability, proliferation, morphology and mineralization for each PLLA configuration. PLLA films were prepared using the solvent cast technique and submitted to different thermal treatments in order to obtain different degrees of crystallinity. Those platforms were then electrically poled, positively and negatively, by corona discharge in order to tailor their electrical properties. The cellular assays were conducted by using two different osteoblast cell lines grown directly onto the PLLA films:Human osteoblast Hob, a primary cell culture and Human osteosarcoma MG-63 cell line. This thesis gives also a comprehensive introduction to the area of Bone Tissue Engineering and provides a review of the work done in this field in the past until today, in that same field, including the one related with bone’s piezoelectricity. Then the experimental part deals with the effects of the crystallinity degrees and of the polarization in terms of surface properties and cellular bio assays. Three different degrees of crystallinity, and three different polarization conditions were prepared; which results in 9 different configurations under investigation.