Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Functional alkali tantalate 2D structures for microelectronics and related applications

Alkali tantalates and niobates, including K(Ta / Nb)O3, Li(Ta / Nb)O3 and Na(Ta / Nb)O3, are a very promising ferroic family of lead-free compounds with perovskite-like structures. Their versatile properties make them potentially interesting for current and future application in microelectronics, photocatalysis, energy and biomedics. Among them potassium tantalate, KTaO3 (KTO), has been raising interest as an alternative for the well-known strontium titanate, SrTiO3 (STO). KTO is a perovskite oxide with a quantum paraelectric behaviour when electrically stimulated and a highly polarizable lattice, giving opportunity to tailor its properties via external or internal stimuli. However problems related with the fabrication of either bulk or 2D nanostructures makes KTO not yet a viable alternative to STO. Within this context and to contribute scientifically to the leverage tantalate based compounds applications, the main goals of this thesis are: i) to produce and characterise thin films of alkali tantalates by chemical solution deposition on rigid Si based substrates, at reduced temperatures to be compatible with Si technology, ii) to fulfil scientific knowledge gaps in these relevant functional materials related to their energetics and ii) to exploit alternative applications for alkali tantalates, as photocatalysis. In what concerns the synthesis attention was given to the understanding of the phase formation in potassium tantalate synthesized via distinct routes, to control the crystallization of desired perovskite structure and to avoid low temperature pyrochlore or K-deficient phases. The phase formation process in alkali tantalates is far from being deeply analysed, as in the case of Pb-containing perovskites, therefore the work was initially focused on the process-phase relationship to identify the driving forces responsible to regulate the synthesis. Comparison of phase formation paths in conventional solid-state reaction and sol-gel method was conducted. The structural analyses revealed that intermediate pyrochlore K2Ta2O6 structure is not formed at any stage of the reaction using conventional solid-state reaction. On the other hand in the solution based processes, as alkoxide-based route, the crystallization of the perovskite occurs through the intermediate pyrochlore phase; at low temperatures pyrochlore is dominant and it is transformed to perovskite at >800 °C. The kinetic analysis carried out by using Johnson-MehlAvrami-Kolmogorow model and quantitative X-ray diffraction (XRD) demonstrated that in sol-gel derived powders the crystallization occurs in two stages: i) at early stage of the reaction dominated by primary nucleation, the mechanism is phase-boundary controlled, and ii) at the second stage the low value of Avrami exponent, n ~ 0.3, does not follow any reported category, thus not permitting an easy identification of the mechanism. Then, in collaboration with Prof. Alexandra Navrotsky group from the University of California at Davis (USA), thermodynamic studies were conducted, using high temperature oxide melt solution calorimetry. The enthalpies of formation of three structures: pyrochlore, perovskite and tetragonal tungsten bronze K6Ta10.8O30 (TTB) were calculated. The enthalpies of formation from corresponding oxides, ∆Hfox, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -203.63 ± 2.84 kJ/mol, - 358.02 ± 3.74 kJ/mol, and -1252.34 ± 10.10 kJ/mol, respectively, whereas from elements, ∆Hfel, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -1408.96 ± 3.73 kJ/mol, -2790.82 ± 6.06 kJ/mol, and -13393.04 ± 31.15 kJ/mol, respectively. The possible decomposition reactions of K-deficient KTa2.2O6 pyrochlore to KTaO3 perovskite and Ta2O5 (reaction 1) or to TTB K6Ta10.8O30 and Ta2O5 (reaction 2) were proposed, and the enthalpies were calculated to be 308.79 ± 4.41 kJ/mol and 895.79 ± 8.64 kJ/mol for reaction 1 and reaction 2, respectively. The reactions are strongly endothermic, indicating that these decompositions are energetically unfavourable, since it is unlikely that any entropy term could override such a large positive enthalpy. The energetic studies prove that pyrochlore is energetically more stable phase than perovskite at low temperature. Thus, the local order of the amorphous precipitates drives the crystallization into the most favourable structure that is the pyrochlore one with similar local organization; the distance between nearest neighbours in the amorphous or short-range ordered phase is very close to that in pyrochlore. Taking into account the stoichiometric deviation in KTO system, the selection of the most appropriate fabrication / deposition technique in thin films technology is a key issue, especially concerning complex ferroelectric oxides. Chemical solution deposition has been widely reported as a processing method to growth KTO thin films, but classical alkoxide route allows to crystallize perovskite phase at temperatures >800 °C, while the temperature endurance of platinized Si wafers is ~700 °C. Therefore, alternative diol-based routes, with distinct potassium carboxylate precursors, was developed aiming to stabilize the precursor solution, to avoid using toxic solvents and to decrease the crystallization temperature of the perovskite phase. Studies on powders revealed that in the case of KTOac (solution based on potassium acetate), a mixture of perovskite and pyrochlore phases is detected at temperature as low as 450 °C, and gradual transformation into monophasic perovskite structure occurs as temperature increases up to 750 °C, however the desired monophasic KTaO3 perovskite phase is not achieved. In the case of KTOacac (solution with potassium acetylacetonate), a broad peak is detected at temperatures <650 °C, characteristic of amorphous structures, while at higher temperatures diffraction lines from pyrochlore and perovskite phases are visible and a monophasic perovskite KTaO3 is formed at >700 °C. Infrared analysis indicated that the differences are due to a strong deformation of the carbonate-based structures upon heating. A series of thin films of alkali tantalates were spin-coated onto Si-based substrates using diol-based routes. Interestingly, monophasic perovskite KTaO3 films deposited using KTOacac solution were obtained at temperature as low as 650 °C; films were annealed in rapid thermal furnace in oxygen atmosphere for 5 min with heating rate 30 °C/sec. Other compositions of the tantalum based system as LiTaO3 (LTO) and NaTaO3 (NTO), were successfully derived as well, onto Si substrates at 650 °C as well. The ferroelectric character of LTO at room temperature was proved. Some of dielectric properties of KTO could not be measured in parallel capacitor configuration due to either substrate-film or filmelectrode interfaces. Thus, further studies have to be conducted to overcome this issue. Application-oriented studies have also been conducted; two case studies: i) photocatalytic activity of alkali tantalates and niobates for decomposition of pollutant, and ii) bioactivity of alkali tantalate ferroelectric films as functional coatings for bone regeneration. Much attention has been recently paid to develop new type of photocatalytic materials, and tantalum and niobium oxide based compositions have demonstrated to be active photocatalysts for water splitting due to high potential of the conduction bands. Thus, various powders of alkali tantalates and niobates families were tested as catalysts for methylene blue degradation. Results showed promising activities for some of the tested compounds, and KNbO3 is the most active among them, reaching over 50 % degradation of the dye after 7 h under UVA exposure. However further modifications of powders can improve the performance. In the context of bone regeneration, it is important to have platforms that with appropriate stimuli can support the attachment and direct the growth, proliferation and differentiation of the cells. In lieu of this here we exploited an alternative strategy for bone implants or repairs, based on charged mediating signals for bone regeneration. This strategy includes coating metallic 316L-type stainless steel (316L-SST) substrates with charged, functionalized via electrical charging or UV-light irradiation, ferroelectric LiTaO3 layers. It was demonstrated that the formation of surface calcium phosphates and protein adsorption is considerably enhanced for 316L-SST functionalized ferroelectric coatings. Our approach can be viewed as a set of guidelines for the development of platforms electrically functionalized that can stimulate tissue regeneration promoting direct integration of the implant in the host tissue by bone ingrowth and, hence contributing ultimately to reduce implant failure.

Efeito da pressão e temperatura em suspensões de amido

O objetivo do presente trabalho consistiu no estudo das propriedades viscoelásticas de suspensões de amido nativo e processado a alta pressão. Foi utilizado um sensor acústico de forma a analisar as propriedades das suspensões, sendo depois recolhidas informações complementares através de outras técnicas: calorimetria diferencial de varrimento, microscopia de luz polarizada e microscopia eletrónica de varrimento. Neste trabalho foram realizados estudos com amido de milho nativo e processado a alta pressão (500 MPa, 5 minutos, temperatura ambiente), tendo-se verificado que a suspensão do amido processado apresentava propriedades viscoelásticas muito diferentes do amido nativo. A temperatura a que se iniciou o aumento da viscosidade foi mais elevada para o amido processado a alta pressão, e as variações observadas para temperaturas superiores a 70 °C foram menores. Durante o arrefecimento foi detetada uma diminuição da viscosidade, correspondente a um aumento da organização molecular, com maior expressão no amido nativo mas que se dá no mesmo intervalo de temperatura, quer para este quer o processado a alta pressão. Foi também possível concluir que a velocidade de aquecimento da amostra de amido influencia as propriedades viscoelásticas da suspensão e as temperaturas a que ocorrem as variações de viscosidade relacionadas com o processo de gelatinização do amido. De assinalar também que no amido de milho se pode detetar pela variação da frequência do cristal piezoelétrico o rompimento dos grânulos e que apesar do estabelecimento de novas ligações e da reposição de alguma ordem molecular que se pode verificar durante o arrefecimento, a frequência da suspensão depois de arrefecida era muito diferente da suspensão de amido inicial. No amido de arroz, a temperatura a que se inicia o aumento de viscosidade foi superior à que se observou para o amido de milho, indicio da maior resistência do amido de arroz, para o qual não se detetou sinal de rutura dos grânulos. A frequência final da suspensão do mesmo, depois de arrefecido, era igual à inicial. Com o amido de arroz foi feito o estudo da influência da temperatura no processamento de alta pressão, tendo sido processadas suspensões a 400 MPa, durante 15 minutos, a 5, 10, 23 e 34 °C. As propriedades viscoelásticas foram analisadas com recurso a um sensor acústico, tendo-se verificado que quanto maior a temperatura de processamento a alta pressão, mais elevada a temperatura necessária para que se inicie o aumento de viscosidade e menores as temperaturas a que se inicia diminuição da mesma durante o arrefecimento.

Características de cinzas e sua aplicação no tratamento de gases durante a gasificação de biomassa

Na procura de melhores combustíveis para a produção de energia térmica e energia elétrica, a biomassa apresenta-se como uma das fontes de energia renováveis menos prejudiciais ao meio ambiente, esta é considerada como um recurso neutro do ponto de vista de emissões de dióxido de carbono. Atualmente, a tecnologia predominante no domínio da conversão energética de biomassa por via termoquímica é a combustão. Contudo, verifica-se a procura de combustíveis de melhor qualidade produzidos a partir de biomassa, como por exemplo na forma gasosa (gás de combustível). A produção deste tipo de combustíveis gasosos envolvendo processos de gasificação carece do desenvolvimento de tecnologia que permita obter um gás combustível com características adequadas às utilizações pretendidas. Os problemas mais relevantes relacionados com a conversão termoquímica da biomassa incluem a produção de cinzas e de alcatrões, estes podem levar a vários problemas operatórios. O presente trabalho teve dois objetivos, a caracterização das cinzas resultantes do processo de combustão de biomassa e o estudo do efeito da aplicação das cinzas para melhorar as propriedades do gás produzido durante o processo de gasificação de biomassa, principalmente na redução de compostos condensáveis (alcatrões). As cinzas volantes da combustão de biomassa analisadas apresentam na sua constituição elementos químicos característicos da biomassa, onde o cálcio apresenta-se em concentrações mais elevadas. Em menores concentrações encontram-se sódio, magnésio, fósforo, enxofre, cloro, potássio, manganês e ferro. As cinzas de fundo, pelo contributo que a areia do leito tem, são caracterizadas por conterem grandes concentrações de silício. Durante os processos de gasificação de biomassa a concentração de compostos condensáveis diminuiu com o aumento da razão de equivalência. As cinzas, colocadas no reator de leito fixo, apresentam um efeito positivo sobre a qualidade do gás, nomeadamente um aumento de 47,8% no teor de H2 e de 11% de CO, consequentemente obteve-se um gás combustível com PCI (poder calorífico inferior) mais elevado.

Caracterização in vitro de um dosímetro de fibra ótica para braquiterapia de HDR

Recentemente foi desenvolvido um dosímetro baseado em fibras cintilantes (BCF-12 da companhia Saint Gobain Crystals com 1 e 0,5 mm de diâmetro e 5 mm de comprimento) para braquiterapia de baixa taxa de dose, em particular a braquiterapia direcionada para o tratamento do cancro da próstata. Este utiliza um novo fotomultiplicador de estado sólido dado pelo nome de MPPC - MultiPixel Photon Counter da companhia Hamamatsu Photonics (Japão). Nesta dissertação é estudado o mesmo dosímetro para a modalidade de braquiterapia de elevada taxa de dose (HDR). A informação sobre a dose neste tipo de dosímetros é obtida a partir de sinais óticos (em vez de sinais elétricos), que são imunes a interferências elétricas e eletromagnéticas. Adicionalmente as pequenas dimensões das fibras oferecem uma excelente resolução espacial e uma invasão mínima para uso em dosimetria in vivo, permitindo medir a dose diretamente ou próximo ao tumor e em tempo real. A sua utilização em braquiterapia para o cancro da próstata constitui-se assim como uma vantagem, uma vez que as fibras podem ser inseridas diretamente nos aplicadores utilizados neste tipo de tratamentos. Apesar de tudo, este tipo de dosímetros possui algumas desvantagens, como por exemplo a luz de Cherenkov e a fluorescência (forma de ruído dada pelo nome de stem effect) que, e a contrário da luz produzida pela fibra cintilante, não são diretamente proporcionais à energia depositada. Contudo, e para energias praticadas em braquiterapia de HDR, nesta dissertação, mostrou-se que este problema é pouco significativo dado que a percentagem de contribuição destes efeitos para o sinal medido é menor que 1% (ou 5% para distâncias menores que 25 mm). Ao longo desta dissertação é feita a caraterização do dosímetro (em modo corrente e impulso) e das suas várias partes em ambiente de laboratório e clínico. Nestes estudos o dosímetro, além de exibir uma boa reprodutibilidade (variação máxima de 3% entre medidas), mostrou uma alta linearidade para uma ampla gama de doses, assim como uma sensibilidade (µGy) semelhante à de uma câmara de ionização, tornando-o adequado para braquiterapia de HDR (tratamento que envolve altos gradientes de dose). Complementarmente, a sua grande versatilidade e simples utilização possibilita a sua aplicação prática em outras modalidades radioterapêuticas.