Nanosensor for assessing the risk of a cardiovascular disease

The incidence of cardiovascular diseases (CVD) has been increasing according to the European and global statistics. Thus, the development of new analytical devices, such as biosensors for assessing the risk of CVD could become a valuable approach for the improvement of healthcare service. In latest years, the nanotechnology has provided new materials with improved electronic properties which have an important contribution in the transduction mechanism of biosensors. Thus, in this thesis, biosensors based on field effect transistors with single-walled carbon nanotubes (NTFET) were developed for the detection of C-reactive protein (CRP) in clinical samples, that is, blood serum and saliva from a group of control patients and a group of CVD risk patients. CRP is an acute-phase protein, which is commonly known as the best validated biomarker for the assessment of CVD, the single-walled carbon nanotubes (SWCNT) were applied as transduction components, and the immunoreaction (interaction between the CRP antigen and the antibodies specific to CRP) was used as the mechanism of molecular recognition for the label-free detection of CRP. After the microfabrication of field effect transistors (FET), the screening of the most important variables for the dispersion of SWCNT, the assemblage of NTFET, and their application on standard solutions of CRP, it was found that NTFET respond accurately to CRP both in saliva and in serum samples, since similar CRP levels were found with the NTFET and the traditional methodology (ELISA technique). On the other hand, a strong correlation between salivary and serum CRP was found with NTFET, which means that saliva could be used, based on non-invasive sampling, as an alternative fluid to blood serum. It was also shown that NTFET could discriminate control patients from CVD risk patients, allowing the determination of a cut-off value for salivary CRP of 1900 ng L-1, which corresponds to the well established cut-off of 3 mg L-1 for CRP in serum, constituting an important finding for the possible establishment of a new range of CRP levels based on saliva. According to the data provided from the volunteer patients regarding their lipoprotein profile and lifestyle factors, it was concluded that the control and the CVD risk patients could be separated taking into account the various risk factors established in literature as strong contributors for developing a CVD, such as triglycerides, serum CRP, total cholesterol, LDL cholesterol, body mass index, Framingham risk score, hypertension, dyslipidemia, and diabetes mellitus. Thus, this work could provide an additional contribution to the understanding of the association of biomarkers levels in serum and saliva samples, and above all, cost-effective, rapid, label-free, and disposable NTFET were developed, based on a noninvasive sampling, for the assessment of CVD risk, thus constituting a potential point-of-care technology.

Phthalocyanines : interaction with carbon structures and as PDT agents

This dissertation describes the synthesis and characterization of different phthalocyanine (Pc) derivatives, as well as some porphyrins (Pors), for supramolecular interaction with different carbon nanostructures, to evaluate their potential application in electronic nanodevices. Likewise, it is also reported the preparation and biological evaluation of interesting phthalocyanine conjugates for cancer photodynamic therapy (PDT) and microorganisms photodynamic inactivation (PDI). The phthalonitrile precursors were prepared from commercial phthalonitriles by nucleophilic substitution of -NO2, -Cl, or -F groups, present in the phthalonitrile core, by thiol or pyridyl units. After the synthesis of these phthalonitriles, the corresponding Pcs were prepared by ciclotetramerization using a metallic salt as template at high temperatures. A second strategy involved the postfunctionalization of hexadecafluorophthalocyaninato zinc(II) through the adequate substituents of mercaptopyridine or cyclodextrin units on the macrocycle periphery. The different compounds were structurally characterized by diverse spectroscopic techniques, namely 1H, 13C and 19F nuclear magnetic resonance spectroscopies (attending the elemental composition of each structure); absorption and emission spectroscopy, and mass spectrometry. For the specific photophysical studies were also used electrochemical characterization, femtosecond and raman spectroscopy, transmission electron and atomic force microscopy. It was highlighted the noncovalent derivatisation of carbon nanostructures, mainly single wall carbon nanotubes (SWNT) and graphene nanosheets with the prepared Pc conjugates to study the photophysical properties of these supramolecular nanoassemblies. Also, from pyridyl-Pors and ruthenium phthalocyanines (RuPcs) were performed Por-RuPcs arrays via coordination chemistry. The results obtained of the novel supramolecular assemblies showed interesting electron donor-acceptor interactions and might be considered attractive candidates for nanotechnological devices. On the other hand, the amphiphilic phthalocyanine-cyclodextrin (Pc-CD) conjugates were tested in biological trials to assess their ability to inhibit UMUC- 3 human bladder cancer cells. The results obtained demonstrated that these photoactive conjugates are highly phototoxic against human bladder cancer cells and could be applied as promising PDT drugs.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Propriedades de lamas de salinas de Aveiro, tendo em vista aplicações dermoterapêuticas e dermocosméticas

Desde tempos históricos que diferentes tipos de lama são utilizados para aplicações externas no corpo humano, para fins terapêuticos e cosméticos. As lamas cuja beneficiação e caracterização físico-química são apresentadas nesta dissertação são formadas no ambiente hipersalino que existe nas salinas da Troncalhada e de São Tiago da Fonte, localizadas no estuário do rio Vouga, em Aveiro, Portugal. As salinas são constituídas por uma sequência de tanques onde, no período de verão, da água do mar e por evaporação natural, se produz sal marinho que precipita no último tanque (o cristalizador) do qual é extraído. Na base dos tanques ocorrem lamas que correspondem a sedimentos constituídos por material argiloso de cor preto-cinzento e que incorporam argila, silte, areia, bioclastos, sal, matéria orgânica e gás. A componente inorgânica da lama extraída do cristalizador foi estudada por Difracção de Raios-X (DRX) e Fluorescência de Raios-X (FRX), enquanto a componente orgânica da mesma lama foi estudada por Cromatografia de Gás- Espectrometria de Massa (GC-MS). Os estudos efectuados incidiram sobre amostras representativas de lama, obtidas antes e após refinação e beneficiação a que foi submetida a lama tal-qual colhida nas salinas. Foram utilizados métodos geofísicos para caracterizar e distinguir as lamas depositadas na época de safra e no período de interregno. Para o efeito, foram cravados tubos amostradores no sedimento que reveste o fundo dos tanques, tubos que seguidamente foram transportados para o laboratório para medição da condutividade eléctrica do topo até à base da coluna de sedimento amostrado. A refinação foi efectuada por elutriação de suspensões aquosas de lama utilizando um equipamento desenvolvido para o efeito e que permitiu concentrar a lama fina no overflow. Após floculação, sifonagem da água sobrenadante, dessalinização e centrifugação a lama refinada e beneficiada pôde ser incorporada em formulações com objectivos terapêuticos e cosméticos. O estudo microbiológico efectuado nas amostras de lama com sal e sem sal e na água das salinas permitiu identificar diversos tipos de bactérias e colónias presentes na lama e avaliar também os processos de esterilização testados. Concluiu-se que a lama hipersalina ou dessalinizada resultante do processamento a que foram submetidas, não deve ser aplicada ou incorporada em formulações tal-qual, pelo facto de em ambas terem sido identificadas bactérias como é o caso de Clostridium perfringens. Não obstante, se submetidas a esterilização utilizando autoclave a lama salina refinada e beneficiada poderá ser aplicada como peloide extemporâneo. Assim sendo foram desenvolvidas formulações dermoterapêuticas e dermocosméticas contendo lama beneficiada e dessalinizada e esterilizada termicamente.

Propriedades intrínsecas e de processamento de termoplásticos elastoméricos incorporando borracha de pneu reciclada

O trabalho apresentado tem por objetivo contribuir para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental. A abordagem adotada para a concretização deste objetivo consiste na incorporação de borracha de pneus em formulações de base termoplástica e elastomérica (TPE), adequadas ao processo de moldação por injeção. São desenvolvidos estudos sobre a morfologia, propriedades mecânicas, térmicas e reológicas das ligas poliméricas à base de granulado de borracha de pneu (GTR). A falta de adesão entre o GTR e a matriz polimérica leva à degradação das propriedades mecânicas dos materiais obtidos. A estratégia explorada passa pela utilização de um elastómero para promover o encapsulamento do GTR e, desta forma, procurar obter ligas com propriedades mecânicas características de um TPE. São analisadas ligas ternárias (TPEGTR) compostas por polipropileno (PP) de elevada fluidez, GTR e elastómero virgem. O efeito da presença de diferentes elastómeros nas ligas é analisado neste trabalho: um elastómero de etilenopropileno- dieno (EPDM), e um novo elastómero de etileno-propileno (EPR) obtido por catálise metalocénica. O estudo da morfologia das ligas obtidas mostra haver interação entre os materiais, sendo possível inferir a viabilidade da estratégia adotada para promover a adesão do GTR. A incorporação de elastómero promove o aumento da resistência ao impacto e da extensão na rotura nas ligas, o que é atribuído, fundamentalmente, ao encapsulamento do GTR e ao aumento da tenacidade da matriz termoplástica. Com o objetivo de avaliar a influência da estrutura cristalina das ligas TPEGTR no seu comportamento mecânico, procede-se à análise do processo de cristalização sob condições isotérmicas e não isotérmicas. Neste estudo, é avaliado o efeito da presença dos materiais que constituem a fase elastomérica na cinética de cristalização. Para cada uma das ligas desenvolvidas, recorre-se ao modelo de Avrami para avaliar o efeito da temperatura no mecanismo de nucleação, na morfologia das estruturas cristalinas e na taxa de cristalização. Recorre-se à reometria capilar para estudar, sob condições estacionárias, o comportamento reológico das ligas TPEGTR. O modelo de Cross-WLF é utilizado para avaliar o comportamento reológico de todos os materiais, obtendo-se resultados similares àqueles obtidos experimentalmente. O comportamento reológico dos polímeros PP, EPR e EPDM é do tipo reofluidificante, tendo o EPR um comportamento reológico similar ao do PP e o EPDM um comportamento reo-fluidificante mais pronunciado. Em todas as ligas analisadas o comportamento reológico revela-se do tipo reo-fluidificante, sendo que a presença de GTR promove o aumento da viscosidade. Os parâmetros obtidos do modelo de Cross-WLF são utilizados para realizar a simulação da etapa de injeção recorrendo a um software comercial. Os resultados obtidos são validados experimentalmente pelo processo de moldação por injeção, evidenciando uma boa adequabilidade da aplicação deste modelo a estas ligas. O trabalho desenvolvido sobre ligas TPEGTR, constitui um contributo para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental.