Multi-standard reconfigurable wireless transmitter architectures

The continuous demand for highly efficient wireless transmitter systems has triggered an increased interest in switching mode techniques to handle the required power amplification. The RF carrier amplitude-burst transmitter, i.e. a wireless transmitter chain where a phase-modulated carrier is modulated in amplitude in an on-off mode, according to some prescribed envelope-to-time conversion, such as pulse-width or sigma-delta modulation, constitutes a promising architecture capable of efficiently transmitting signals of highly demanding complex modulation schemes. However, the tested practical implementations present results that are way behind the theoretically advanced promises (perfect linearity and efficiency). My original contribution to knowledge presented in this thesis is the first thorough study and model of the power efficiency and linearity characteristics that can be actually achieved with this architecture. The analysis starts with a brief revision of the theoretical idealized behavior of these switched-mode amplifier systems, followed by the study of the many sources of impairments that appear when the real system is implemented. In particular, a special attention is paid to the dynamic load modulation caused by the often ignored interaction between the narrowband signal reconstruction filter and the usual single-ended switched-mode power amplifier, which, among many other performance impairments, forces a two transistor implementation. The performance of this architecture is clearly explained based on the presented theory, which is supported by simulations and corresponding measured results of a fully working implementation. The drawn conclusions allow the development of a set of design rules for future improvements, one of which is proposed and verified in this thesis. It suggests a significant modification to this traditional architecture, where now the phase modulated carrier is always on – and thus allowing a single transistor implementation – and the amplitude is impressed into the carrier phase according to a bi-phase code.

Nonlinear distortion generation mechanisms in Doherty amplifiers

Nowadays, wireless communications systems demand for greater mobility and higher data rates. Moreover, the need for spectral efficiency requires the use of non-constant envelope modulation schemes. Hence, power amplifier designers have to build highly efficient, broadband and linear amplifiers. In order to fulfil these strict requirements, the practical Doherty amplifier seems to be the most promising technique. However, due to its complex operation, its nonlinear distortion generation mechanisms are not yet fully understood. Currently, only heuristic interpretations are being used to justify the observed phenomena. Therefore, the main objective of this work is to provide a model capable of describing the Doherty power amplifier nonlinear distortion generation mechanisms, allowing the optimization of its design according to linearity and efficiency criteria. Besides that, this approach will allow a bridge between two different worlds: power amplifier design and digital pre-distortion since the knowledge gathered from the Doherty operation will serve to select the most suitable pre-distortion models.

Amplificador de RF Doherty assimétrico de 2-vias

Os atuais esquemas de modulação e acesso ao meio, tais como o Wide- Band Code-Division Multiple Access (WCDMA) ou Orthogonal Frequency- Division Multiple Access (OFDMA), que são otimizados para a gestão eficiente do espetro electromagnético e elevada taxa de transmissão, originam sinais de elevado Peak-to-Average Power Ratio (PAPR) e requisitos de linearidade rigorosos. As arquiteturas de amplificação tradicionais, i.e. baseadas no operação em modo de corrente do dispositivo ativo, são incapazes de satisfazer estes requisitos em simultâneo. Assim, o amplificador de potência (do inglês, Power Ampli_er (PA)) incorre numa degradação significativa de rendimento energético em favor de maior linearidade, aumentando simultaneamente os custos de operação das estacões base para os operadores de telecomunicações móveis e o impacte ambiental. Este trabalho foca-se no estudo da arquitetura Doherty, a principal solução encontrada para melhorar o compromisso linearidade/rendimento para aplicações em estações-base de comunicações móveis. Para tal, são expostos os princípios básicos de amplificadores de rádio frequência assim como a análise teórica do tradicional PA Doherty (do inglês, Doherty Power Amplifier (DhPA)) de duas vias e suas variantes. O estudo _e complementado com o projeto e implementação de um PA excitador, em classe-AB, e de um DhPA de elevada potência, colocando-se em prática a teoria e técnicas de projeto estudadas ao longo deste trabalho, aliadas aos desafios da implementação com dispositivos reais de elevada potência.