Assessing the combined effect of land management and wildfire on runoff and soil erosion in north central Portugal

Strong and sometimes extreme responses in runoff and soil erosion following wildfires have been reported worldwide. However, in the case of North-Central Portugal, little research had been carried out regarding the hydrologic and erosive impacts of several land management activities in recently burnt areas (such as ground preparation, post-fire logging or post-fire mitigation treatments). This study aims to assess post-fire runoff and soil erosion response on Eucalypt and Maritime pine plantations during the first, second and third years following wildfires. The effect of several pre-fire ground preparation operations (ploughed down-slope, contour ploughed and inclined terraces), post-fire logging activities (on both the eucalypt and pine plantations), as well as the application of hydromulch (a post-fire emergency treatment) on overland flow and soil erosion were compared to burnt but undisturbed and untreated areas. The intensive monitoring of runoff, soil erosion and selected soil properties served to determine the main factors involved in post-fire runoff and soil erosion and their spatial and temporal variation. Soil water repellency deserved special attention, due to its supposed important role for overland flow generation. Repeated rainfall simulation experiments (RSE’s), micro-scale runoff plots and bounded sediment fences were carried out and/or installed immediately after the wildfire on seven burnt slopes. Micro-scale runoff plots results under natural rainfall conditions were also compared to the RSE’s results, which was useful for assessing the representativeness of the data obtained with artificial rainfall. The results showed comparable runoff coefficient (20-60%) but lower sediment losses (125-1000 g m-2) than prior studies in Portugal, but especially outside Portugal. Lower sediment losses were related with the historic intensive land use in the area. In evaluating these losses, however, the shallowness and stoniness of the soils, as well as the high organic matter fraction of the eroded sediments (50%) must not be overlooked. Sediment limited erosion was measured in all the ploughed sites, probably due to the time since ploughing (several years). The disturbance of the soil surface cover due to post-fire logging and wood extraction substantially increased sediment losses at both the pine and eucalypt sites. Hydromulch effectiveness in reducing the runoff (70%) and sediment losses (83%) was attributed to the protective high coverage provided by hydromulch. The hydromulch significantly affected the soil cover and other soil properties and these changes also reduced the soil erosion risk. The rainfall amount was the main factor explaining the variance in runoff. However, a shift from rainfall amount to rainfall intensity was detected when either the surface cover or the infiltration capacity (hydrophilic conditions) increased. Sediment losses were controlled by rainfall intensity and surface cover. The role of soil water repellency on runoff generation was not consistent; the overall repellency levels alone were not enough to assess its hydrological impact. Soil water repellency explained runoff generation in the specific-sites model better than in the overall model. Additionally, soil moisture content was a better predictor for soil water repellency than antecedent rainfall. The natural rainfall results confirmed that RSE’s were able to capture the specific sediment losses and its organic matter content as well as the differences between the ploughed and unploughed sites. Repeated RSE’s also captured the seasonal variations in runoff and sediment losses attributed to soil water repellency. These results have implications for post-fire soil erosion modelling and soil conservation practices in the region, or areas with the same land use, climate and soil characteristics. The measured sediment loss, as well as the increasing frequency of ploughing in recently burnt and unburnt eucalypt stands, suggests ploughing is not an effective as a soil conservation measure. Logging activities with less impact are recommended in order to maintain the forest litter protecting the soil surface. Due to its high effectiveness in reducing runoff and soil erosion, hydromulch is recommended for highly sensitive and vulnerable areas.

Multilayered micro/nanocrystalline CVD diamond coatings for biotribology

In the present work multilayered micro/nanocrystalline (MCD/NCD) diamond coatings were developed by Hot Filament Chemical Vapour Deposition (HFCVD). The aim was to minimize the surface roughness with a top NCD layer, to maximize adhesion onto the Si3N4 ceramic substrates with a starting MCD coating and to improve the mechanical resistance by the presence of MCD/NCD interfaces in these composite coatings. This set of features assures high wear resistance and low friction coefficients which, combined to diamond biocompatibility, set this material as ideal for biotribological applications. The deposition parameters of MCD were optimized using the Taguchi method, and two varieties of NCD were used: NCD-1, grown in a methane rich gas phase, and NCD-2 where a third gas, Argon, was added to the gas mixture. The best combination of surface pre-treatments in the Si3N4 substrates is obtained by polishing the substrates with a 15 μm diamond slurry, further dry etching with CF4 plasma for 10 minutes and final ultrasonic seeding in a diamond powder suspension in ethanol for 1 hour. The interfaces of the multilayered CVD diamond films were characterized with high detail using HRTEM, STEM-EDX and EELS. The results show that at the transition from MCD to NCD a thin precursor graphitic film is formed. On the contrary, the transition of the NCD to MCD grade is free of carbon structures other than diamond, as a result of the richer atomic hydrogen content and of the higher substrate temperature for MCD deposition. At those transitions, WC nanoparticles were found due to contamination from the filament, being also present at the first interface of the MCD layer with the silicon nitride substrate. In order to study the adhesion and mechanical resistance of the diamond coatings, indentation and particle jet blasting tests were conducted, as well as tribological experiments with homologous pairs. Indentation tests proved the superior behaviour of the multilayered coatings that attained a load of 800 N without delamination, when compared to the mono and bilayered ones. The multilayered diamond coatings also reveal the best solid particle erosion resistance, due to the MCD/NCD interfaces that act as crack deflectors. These results were confirmed by an analytical model on the stress field distribution based on the von Mises criterion. Regarding the tribological testing under dry sliding, multilayered coatings also exhibit the highest critical load values (200N for Multilayers with NCD-2). Low friction coefficient values in the range μ=0.02- 0.09 and wear coefficient values in the order of ~10-7 mm3 N-1 m-1 were obtained for the ball and flat specimens indicating a mild wear regime. Under lubrication with physiological fluids (HBSS e FBS), lower wear coefficient values ~10-9-10-8 mm3 N-1 m-1) were achieved, governed by the initial surface roughness and the effective contact pressure.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.