Treatment of aqueous effluents contaminated with ionic liquids

Ionic liquids are a class of solvents that, due to their unique properties, have been proposed in the past few years as alternatives to some hazardous volatile organic compounds. They are already used by industry, where it was possible to improve different processes by the incorporation of this kind of non-volatile and often liquid solvents. However, even if ionic liquids cannot contribute to air pollution, due to their negligible vapour pressures, they can be dispersed thorough aquatic streams thus contaminating the environment. Therefore, the main goals of this work are to study the mutual solubilities between water and different ionic liquids in order to infer on their environmental impact, and to propose effective methods to remove and, whenever possible, recover ionic liquids from aqueous media. The liquid-liquid phase behaviour of different ionic liquids and water was evaluated in the temperature range between (288.15 and 318.15) K. For higher melting temperature ionic liquids a narrower temperature range was studied. The gathered data allowed a deep understanding on the structural effects of the ionic liquid, namely the cation core, isomerism, symmetry, cation alkyl chain length and the anion nature through their mutual solubilities (saturation values) with water. The experimental data were also supported by the COnductor-like Screening MOdel for Real Solvents (COSMO-RS), and for some more specific systems, molecular dynamics simulations were also employed for a better comprehension of these systems at a molecular level. On the other hand, in order to remove and recover ionic liquids from aqueous solutions, two different methods were studied: one based on aqueous biphasic systems, that allowed an almost complete recovery of hydrophilic ionic liquids (those completely miscible with water at temperatures close to room temperature) by the addition of strong salting-out agents (Al2(SO4)3 or AlK(SO4)2); and the other based on the adsorption of several ionic liquids onto commercial activated carbon. The first approach, in addition to allowing the removal of ionic liquids from aqueous solutions, also makes possible to recover the ionic liquid and to recycle the remaining solution. In the adsorption process, only the removal of the ionic liquid from aqueous solutions was attempted. Nevertheless, a broad understanding of the structural effects of the ionic liquid on the adsorption process was attained, and a final improvement on the adsorption of hydrophilic ionic liquids by the addition of an inorganic salt (Na2SO4) was also achieved. Yet, the development of a recovery process that allows the reuse of the ionic liquid is still required for the development of sustainable processes.

Regional and urban air quality modelling under a climate change scenario

The better understanding of the interactions between climate change and air quality is an emerging priority for research and policy. Climate change will bring changes in the climate system, which will affect the concentration and dispersion of air pollutants. The main objective of the current study is to assess the impacts of climate change on air quality in 2050 over Portugal and Porto urban area. First, an evaluation and characterization of the air quality over mainland Portugal was performed for the period between 2002 and 2012. The results show that NO2, PM10 and O3 are the critical pollutants in Portugal. Also, the influence of meteorology on O3, NO2 and PM10 levels was investigate in the national main urban areas (Porto and Lisboa) and was verified that O3 has a statistically significant relationship with temperature in most of the components. The results also indicate that emission control strategies are primary regulators for NO2 and PM10 levels. After, understanding the national air quality problems and the influence that meteorology had in the historical air quality levels, the air quality modelling system WRF-CAMx was tested and the required inputs for the simulations were prepared to fulfil the main goal of this work. For the required air quality modelling inputs, an Emission Projections under RCP scenarios (EmiPro-RCP) model was developed to assist the estimation of future emission inventories for GHG and common air pollutants. Also, the current emissions were estimated for Portugal with a higher detailed disaggregation to improve the performance of the air quality simulations. The air quality modelling system WRF/CAMx was tested and evaluated over Portugal and Porto urban area and the results point out that is an adequate tool for the analysis of air quality under climate change. For this purpose, regional simulations of air quality during historical period and future (2045-2050) were conducted with CAMx version 6.0 to evaluate the impacts of simulated future climate and anthropogenic emission projections on air quality over the study area. The climate and the emission projections were produced under the RCP8.5 scenario. The results from the simulations point out, that if the anthropogenic emissions keep the same in 2050, the concentrations of NO2, PM10 and O3 will increase in Portugal. When, besides the climate change effects, is consider the projected anthropogenic emissions the annual mean concentrations of NO2 decrease significantly in Portugal and Porto urban area, and on the contrary the annual mean PM10 concentrations increases in Portugal and decrease in Porto urban area. The O3 results are mainly caused by the reduction of ozone precursors, getting the higher reductions in urban areas and increases in the surrounding areas. All the analysis performed for both simulations for Porto urban area support that, for PM10 and O3, there will be an increase in the occurrence of extreme values, surpassing the annual legislated parameters and having more daily exceedances. This study constitutes an innovative scientific tool to help in future air quality management in order to mitigate future climate change impacts on air quality.

Assessing the effectiveness of chemical treatment with nanomaterials in improving the quality of different industrial effluents

Industrial activities are the major sources of pollution in all environments. Depending on the type of industry, various levels of organic and inorganic pollutants are being continuously discharged into the environment. Although, several kinds of physical, chemical, biological or the combination of methods have been proposed and applied to minimize the impact of industrial effluents, few have proved to be totally effective in terms of removal rates of several contaminants, toxicity reduction or amelioration of physical and chemical properties. Hence, it is imperative to develop new and innovative methodologies for industrial wastewater treatment. In this context nanotechnology arises announcing the offer of new possibilities for the treatment of wastewaters mainly based on the enhanced physical and chemical proprieties of nanomaterials (NMs), which can remarkably increase their adsorption and oxidation potential. Although applications of NMs may bring benefits, their widespread use will also contribute for their introduction into the environment and concerns have been raised about the intentional use of these materials. Further, the same properties that make NMs so appealing can also be responsible for producing ecotoxicological effects. In a first stage, with the objective of selecting NMs for the treatment of organic and inorganic effluents we first assessed the potential toxicity of nanoparticles of nickel oxide (NiO) with two different sizes (100 and 10-20 nm), titanium dioxide (TiO2, < 25 nm) and iron oxide (Fe2O3, ≈ 85x425 nm). The ecotoxicological assessment was performed with a battery of assays using aquatic organisms from different trophic levels. Since TiO2 and Fe2O3 were the NMs that presented lower risks to the aquatic systems, they were selected for the second stage of this work. Thus, the two NMs pre-selected were tested for the treatment of olive mill wastewater (OMW). They were used as catalyst in photodegradation systems (TiO2/UV, Fe2O3/UV, TiO2/H2O2/UV and Fe2O3/H2O2/UV). The treatments with TiO2 or Fe2O3 combined with H2O2 were the most efficient in ameliorating some chemical properties of the effluent. Regarding the toxicity to V. fischeri the highest reduction was recorded for the H2O2/UV system, without NMs. Afterwards a sequential treatment using photocatalytic oxidation with NMs and degradation with white-rot fungi was applied to OMW. This new approach increased the reduction of chemical oxygen demand, phenolic content and ecotoxicity to V. fischeri. However, no reduction in color and aromatic compounds was achieved after 21 days of biological treatment. The photodegradation systems were also applied to treat the kraft pulp mill and mining effluents. For the organic effluent the combination NMs and H2O2 had the best performances in reduction the chemical parameters as well in terms of toxicity reduction. However, for the mine effluent the best (TiO2/UV and Fe2O3/UV) were only able to significantly remove three metals (Zn, Al and Cd). Nonetheless the treatments were able of reducing the toxicity of the effluent. As a final stage, the toxicity of solid wastes formed during wastewater treatment with NMs was assessed with Chironomus riparius larvae, a representative species of the sediment compartment. Certain solid wastes showed the potential to negatively affect C. riparius survival and growth, depending on the type of effluent treated. This work also brings new insights to the use of NMs for the treatment of industrial wastewaters. Although some potential applications have been announced, many evaluations have to be performed before the upscaling of the chemical treatments with NMs.