Commercial oyster stocks as a potential source of larvae in the regeneration of Ostrea edulis in Strangford Lough, Northern Ireland.

Ostrea edulis was extremely rare in the wild in Strangford Lough from the early 1900s until renewed spatfall was observed at a number of sites in the 1990s. A monitoring programme was undertaken to investigate the presence and distribution of planktonic oyster larvae at nine sites around the lough between June and September in 1997 and 1998 as a precursor to studies of spatfall patterns. Larval densities at sites in the northern basin of the lough were significantly higher than those in the southern basin where larvae were lacking or in low numbers. Densities and sizes of oyster larvae showed significant temporal variation suggesting pulsed larval release. Larval densities also showed significant spatial variation with higher densities at sites closer to commercial stocks pointing to these as the main source of oyster larvae. This hypothesis was supported during a larval flux study over a complete tidal cycle which indicated a 90% net tidal movement of O. edulis larvae from the entrance of the bay where commercial stocks were held to the main body of the lough. Thus the maintenance of dense commercial stocks of flat oysters may provide the key to the redevelopment of native oyster beds in Strangford Lough and elsewhere by providing an initial broodstock nucleus from which larvae can be exported.

Exporting Europeanisation to the Wider Europe: the Twinning Excercise and Administrative Reform in the Candidate Countries and Beyond

This article looks at the EU's efforts to assist administrative reform in Eastern Europe, with particular attention to the twinning exercise, conceptually linked to Europeanization. The article argues that much of the debate on Europeanization has focused predominantly on the way in which existing member states are being transformed as a result of their participation in EU structures. Yet the political importance attached to EU membership by the accession applicants, as well as EU's determination to ensure compliance with the acquis communautaire prior to entry, indicates that Europeanization is not only confined to existing EU member states, but can be exported outside the geographical borders of the EU. Against this background the article argues that extending the scope of the Europeanization thesis beyond existing members can not only help us understand better the process of transformation in Eastern Europe and the ongoing accession negotiations, but can also contribute towards the refinement of the term's rather blurred conceptual content.

Nitrogen budget for the Oldman River Basin, southern Alberta, Canada

The Oldman River Basin (OMRB), located in southern Alberta (Canada), with an area of 28,200 km2, is mainly forested in its western part and is used for intensive agriculture in its eastern part. The objective of this paper is to estimate the nitrogen (N) budget for the Oldman River Basin as a whole and its sub-basins, and to discuss differences in the N budget between various sub-basins. Better knowledge of the N budget in this watershed may be also utilized for understanding N dynamics in similar watersheds within semi-arid climatic regions. The model used is a mass balance spreadsheet model that takes into account N inputs and N export through surface water. During the last 120 years, anthropogenic N inputs to the OMRB have increased circa 40 fold. By the end of the 20th century, the OMRB received an annualN input of about 5174 kg N km-2 yr-1, whereas only about 25 kg N km-2 yr-1 were exported via riverine flow. For the sub-basins, annual N inputs ranged from 2516 to 19011 kg N km-2 yr-1, and annual N export via riverine flows varied between 6 and 277 kg N km-2 yr-1. Over 85% of total N inputs to the OMRB are due to anthropogenic activities, including manure (55%), synthetic fertilizer (27%), and N fixation on agricultural lands (4%). Sewage accounted for less than 1%, and N inputs from atmospheric deposition and fixation in forests represented 6 and 8% respectively. Despite increasing anthropogenic N inputs, N export with riverine flow currently accounts for only 1% of the inputs, indicating thatmost of theNinputs are currently retained in the OMRB or are re-emitted into the atmosphere.

Selective extracellular vesicle-mediated export of an overlapping set of microRNAs from multiple cell types

Background: MicroRNAs (miRNAs) are a class of small RNA molecules that regulate expression of specific mRNA targets. They can be released from cells, often encapsulated within extracellular vesicles (EVs), and therefore have the potential to mediate intercellular communication. It has been suggested that certain miRNAs may be selectively exported, although the mechanism has yet to be identified. Manipulation of the miRNA content of EVs will be important for future therapeutic applications. We therefore wished to assess which endogenous miRNAs are enriched in EVs and how effectively an overexpressed miRNA would be exported.

Results: Small RNA libraries from HEK293T cells and vesicles before or after transfection with a vector for miR-146a overexpression were analysed by deep sequencing. A subset of miRNAs was found to be enriched in EVs; pathway analysis of their predicted target genes suggests a potential role in regulation of endocytosis. RT-qPCR in additional cell types and analysis of publicly available data revealed that many of these miRNAs tend to be widely preferentially exported. Whilst overexpressed miR-146a was highly enriched both in transfected cells and their EVs, the cellular:EV ratios of endogenous miRNAs were not grossly altered. MiR-451 was consistently the most highly exported miRNA in many different cell types. Intriguingly, Argonaute2 (Ago2) is required for miR-451 maturation and knock out of Ago2 has been shown to decrease expression of other preferentially exported miRNAs (eg miR-150 and miR-142-3p).

Conclusion: The global expression data provided by deep sequencing confirms that specific miRNAs are enriched in EVs released by HEK293T cells. Observation of similar patterns in a range of cell types suggests that a common mechanism for selective miRNA export may exist.

An Escherichia coli undecaprenyl-pyrophosphate phosphatase implicated in undecaprenyl phosphate recycling

Undecaprenyl phosphate (Und-P) is a universal lipid carrier of glycan biosynthetic intermediates for carbohydrate polymers that are exported to the bacterial cell envelope. Und-P arises from the dephosphorylation of undecaprenyl pyrophosphate (Und-PP) molecules produced by de novo synthesis and also from the recycling of released Und-PP after the transfer of the glycan component to other acceptor molecules. The latter reactions take place at the periplasmic side of the plasma membrane, while cytoplasmic enzymes catalyse the de novo synthesis. Four Und-PP pyrophosphatases were recently identified in Escherichia coli. One of these, UppP (formerly BacA), accounts for 75 % of the total cellular Und-PP pyrophosphatase activity and has been suggested to participate in the Und-P de novo synthesis pathway. Unlike UppP, the other three pyrophosphatases (YbjG, YeiU and PgpB) have a typical acid phosphatase motif also found in eukaryotic dolichyl-pyrophosphate-recycling pyrophosphatases. This study shows that double and triple deletion mutants in the genes uppP and ybjG, and uppP, ybjG and yeiU, respectively, are supersensitive to the Und-P de novo biosynthesis inhibitor fosmidomycin. In contrast, single or combined deletions including pgpB have no effect on fosmidomycin supersensitivity. Experimental evidence is also presented that the acid phosphatase motifs of YbjG and YeiU face the periplasmic space. Furthermore, the quadruple deletion mutant DeltauppP-DeltaybjG-DeltayeiU-DeltawaaL has a growth defect and abnormal cell morphology, suggesting that accumulation of unprocessed Und-PP-linked O antigen polysaccharides is toxic for these cells. Together, the results support the notion that YbjG, and to a lesser extent YeiU, exert their enzymic activity on the periplasmic side of the plasma membrane and are implicated in the recycling of periplasmic Und-PP molecules.

Characterizing Pb mobilization from upland soils to streams using (206)Pb/(207)Pb isotopic ratios

Anthropogenically deposited lead (Pb) binds efficiently to soil organic matter, which can be mobilized through hydrologically mediated mechanisms, with implications for ecological and potable quality of receiving waters. Lead isotopic ((206)Pb/(207)Pb) ratios change down peat profiles as a consequence of long-term temporal variation in depositional sources, each with distinctive isotopic signatures. This study characterizes differential Pb transport mechanisms from deposition to streams at two small catchments with contrasting soil types in upland Wales, U.K., by determining Pb concentrations and (206)Pb/(207)Pb ratios from soil core profiles, interstitial pore waters, and stream water. Hydrological characteristics of soils are instrumental in determining the location in soil profiles of exported Pb and hence concentration and (206)Pb/(207)Pb ratios in surface waters. The highest Pb concentrations from near-surface soils are mobilized, concomitant with high dissolved organic carbon (DOC) exports, from hydrologically responsive peat soils with preferential shallow subsurface flows, leading to increased Pb concentrations in stream water and isotopic signatures more closely resembling recently deposited Pb. In more minerogenic soils, percolation of water allows Pb, bound to DOC, to be retained in mineral horizons and combined with other groundwater sources, resulting in Pb being transported from throughout the profile with a more geogenic isotopic signature. This study shows that (206)Pb/(207)Pb ratios can enhance our understanding of the provenances and transport mechanisms of Pb and potentially organic matter within upland soils.

Chlorobenzenes in rivers draining industrial catchments

Eleven chlorobenzenes (out of a total of 12 in the congener series) were monitored weekly on four industrialized rivers (Aire, Calder, Don and Trent) of the Southern Humber Catchment in whole water samples. 1,2- and 1,4-dichlorobenzene were present at relatively high levels on both the Aire and Calder, having mean concentrations of approximately 30 ng/l. They were both at lower concentrations on the Don and Trent, although the 1,4-isomer dominated. All other chlorobenzenes monitored were routinely found on all the rivers, with the exception of hexachlorobenzene, which was only regularly detected on the Trent. Again, the rivers fell into two classes with respect to their total chlorobenzene concentrations, with the Aire and Calder being more polluted. The higher levels of chlorobenzenes (excluding hexachlorobenzene which was used widely as a agricultural pesticide) on the Aire and Calder, and the dominance of the 1,4-dichlorobenzene congener (accounting for 60-70% of sigma chlorobenzenes) on the Don and Trent, indicated that the Aire and Calder were predominately contaminated with chlorobenzenes through industrial sources, while the Don and Trent were mainly contaminated through domestic sources (1,4-dichlorobenzene is widely used as a toilet deodorant). 1,4-Dichlorobenzene dominated flux, with the Aire, Don and Trent exporting 52.5 kg/year into the Humber estuary, followed by the 1,2-dichlorobenzene at 38.8 kg/year. Sigma chlorobenzenes exported to the Humber was 133 kg/year. This is the first study to calculate chlorobenzene fluxes to the North Sea from a UK catchment.

The Bdellovibrio bacteriovorus twin-arginine transport system has roles in predatory and prey-independent growth

Bdellovibrio bacteriovorus grows in one of two ways: either (i) predatorily [in a host-dependent (HD) manner], when it invades the periplasm of another Gram-negative bacterium, exporting into the prey co-ordinated waves of soluble enzymes using the prey cell contents for growth; or (ii) in a host-independent (HI) manner, when it grows (slowly) axenically in rich media. Periplasmic invasion potentially exposes B. bacteriovorus to extremes of pH and exposes the need to scavenge electron donors from prey electron transport components by synthesis of metalloenzymes. The twin-arginine transport system (Tat) in other bacteria transports folded metalloenzymes and the B. bacteriovorus genome encodes 21 potential Tat-transported substrates and Tat transporter proteins TatA1, TatA2 and TatBC. GFP tagging of the Tat signal peptide from Bd1802, a high-potential iron-sulfur protein (HiPIP), revealed it to be exported into the prey bacterium during predatory growth. Mutagenesis showed that the B. bacteriovorus tatA2 and tatC gene products are essential for both HI and HD growth, despite the fact that they partially complement (in SDS resistance assays) the corresponding mutations in Escherichia coli where neither TatA nor TatC are essential for life. The essentiality of B. bacteriovorus TatA2 was surprising given that the B. bacteriovorus genome encodes a second tatA homologue, tatA1. Transcription of tatA1 was found to be induced upon entry to the bdelloplast, and insertional inactivation of tatA1 showed that it significantly slowed the rates of both HI and HD growth. B. bacteriovorus is one of a few bacterial species that are reliant on a functional Tat system and where deletion of a single tatA1 gene causes a significant growth defect(s), despite the presence of its tatA2 homologue.

An Integrated Toolkit for the Conservation of Stone-Built Heritage

Rapid in situ diagnosis of damage is a key issue in the preservation of stone-built cultural heritage. This is evident in the increasing number of congresses, workshops and publications dealing with this issue. With this increased activity has come, however, the realisation that for many culturally significant artefacts it is not possible either to remove samples for analysis or to affix surface markers for measurement. It is for this reason that there has been a growth of interest in non-destructive and minimally invasive techniques for characterising internal and external stone condition. With this interest has come the realisation that no single technique can adequately encompass the wide variety of parameters to be assessed or provide the range of information required to identify appropriate conservation. In this paper we describe a strategy to address these problems through the development of an integrated `tool kit' of measurement and analytical techniques aimed specifically at linking object-specific research to appropriate intervention. The strategy is based initially upon the acquisition of accurate three-dimensional models of stone-built heritage at different scales using a combination of millimetre accurate LiDAR and sub-millimetre accurate Object Scanning that can be exported into a GIS or directly into CAD. These are currently used to overlay information on stone characteristics obtained through a combination of Ground Penetrating Radar, Surface Permeametry, Colorimetry and X-ray Fluorescence, but the possibility exists for adding to this array of techniques as appropriate. In addition to the integrated three-dimensional data array provided by superimposition upon Digital Terrain Models, there is the capability of accurate re-measurement to show patterns of surface loss and changes in material condition over time. Thus it is possible to both record and base-line condition and to identify areas that require either preventive maintenance or more significant pre-emptive intervention. In pursuit of these goals the authors are developing, through a UK Government supported collaboration between University Researchers and Conservation Architects, commercially viable protocols for damage diagnosis, condition monitoring and eventually mechanisms for prioritizing repairs to stone-built heritage. The understanding is, however, that such strategies are not age-constrained and can ultimately be applied to structures of any age.

The Fate of Terrestrial Carbon in a Complex Lake System: Lough Erne

Lake food webs were in the past viewed as being fuelled solely by primary production – i.e. by photosynthetic plants and algae. However this has changed as the exports of terrestrial areas into lakes have been taken into account. Previously, terrestrial carbon in lakes was thought to have been buried in sediments or exported to the atmosphere, however recent studies have indicated that terrestrial carbon can supplement primary production in some lakes, or in others be the dominant source of production for the lake food web. In this study radiocarbon has been used in conjunction with stable carbon and nitrogen isotopes to show the utilisation of terrestrial carbon in the food web. The fate of terrestrial carbon in the lake will be discussed as well as the possible mechanisms for the transfer of terrestrial carbon for utilisation in the lake.

Parametric CAD model based shape optimization using adjoint functions

Adjoint methods have proven to be an efficient way of calculating the gradient of an objective function with respect to a shape parameter for optimisation, with a computational cost nearly independent of the number of the design variables [1]. The approach in this paper links the adjoint surface sensitivities (gradient of objective function with respect to the surface movement) with the parametric design velocities (movement of the surface due to a CAD parameter perturbation) in order to compute the gradient of the objective function with respect to CAD variables.
For a successful implementation of shape optimization strategies in practical industrial cases, the choice of design variables or parameterisation scheme used for the model to be optimized plays a vital role. Where the goal is to base the optimization on a CAD model the choices are to use a NURBS geometry generated from CAD modelling software, where the position of the NURBS control points are the optimisation variables [2] or to use the feature based CAD model with all of the construction history to preserve the design intent [3]. The main advantage of using the feature based model is that the optimized model produced can be directly used for the downstream applications including manufacturing and process planning.
This paper presents an approach for optimization based on the feature based CAD model, which uses CAD parameters defining the features in the model geometry as the design variables. In order to capture the CAD surface movement with respect to the change in design variable, the “Parametric Design Velocity” is calculated, which is defined as the movement of the CAD model boundary in the normal direction due to a change in the parameter value.
The approach presented here for calculating the design velocities represents an advancement in terms of capability and robustness of that described by Robinson et al. [3]. The process can be easily integrated to most industrial optimisation workflows and is immune to the topology and labelling issues highlighted by other CAD based optimisation processes. It considers every continuous (“real value”) parameter type as an optimisation variable, and it can be adapted to work with any CAD modelling software, as long as it has an API which provides access to the values of the parameters which control the model shape and allows the model geometry to be exported. To calculate the movement of the boundary the methodology employs finite differences on the shape of the 3D CAD models before and after the parameter perturbation. The implementation procedure includes calculating the geometrical movement along a normal direction between two discrete representations of the original and perturbed geometry respectively. Parametric design velocities can then be directly linked with adjoint surface sensitivities to extract the gradients to use in a gradient-based optimization algorithm.
The optimisation of a flow optimisation problem is presented, in which the power dissipation of the flow in an automotive air duct is to be reduced by changing the parameters of the CAD geometry created in CATIA V5. The flow sensitivities are computed with the continuous adjoint method for a laminar and turbulent flow [4] and are combined with the parametric design velocities to compute the cost function gradients. A line-search algorithm is then used to update the design variables and proceed further with optimisation process.