Optimisation of time/temperature treatment, for heat treated soft wheat flour

Chlorination of wheat flour in the EU countries has been replaced in recent years, to some extent, by heat treated flour which is used to produce high ratio cakes. Heat treated flour allows high ratio recipes to be developed which generate products with longer shelf life, finer texture, moist crumb and sweeter taste. The mechanism by which heat treatment improves the flour is not fully understood, but it is known that during the heat treatment process, protein denaturation and partial gelatinisation of the starch granules occurs, as well as an increase in batter viscosity. Therefore, it is important to optimize the flour heat treatment process, in order to enhance baking quality. Laboratory preparation of heat treated base wheat flour (culinary, soft, low protein) was carried out in a fluidised bed drier using a range of temperatures and times. The gluten was extracted from the final product and its quality was tested, to obtain objective and comparative information on the extent of protein denaturation. The results indicated that heat treatment of flour decreases gluten extensibility and partial gelatinisation of the starch granules occurred. After heat treatment the gluten appeared to retain moisture. The optimum time/temperature for the heat treatment of base flour was 120-130°C for 30 min with moisture content of ˜12.5%.© 2012 Elsevier Ltd. All rights reserved.

Assessment of the solubility and bioaccessibility of arsenic in realgar wine using a simulated gastrointestinal system

Consumption of arsenic (As) wine is a traditional activity during the classic Chinese festival of Duanwu, colloquially known worldwide as the Dragon Boat Day. Arsenic wine is drunk on the morning of the fifth day of the fifth lunar calendar month to commemorate the death of Qu Yuan, a famed Chinese poet who drowned himself in protest of a corrupt government, and to protect against ill fortune. Although realgar minerals are characteristically composed of sparingly soluble tetra-arsenic tetra-sulfides (As(4)S(4)), purity does vary with up to 10% of As being present as non-sulfur bound species, such as arsenate (As(v)) and arsenite (As(III)). Despite, the renewed interest in As speciation and the bioaccessibility of the active As components in realgar based Chinese medicines, little is known about the safety surrounding the cultural practice of drinking As wine. In a series of experiments the speciation and solubility of As in a range of wines were investigated. Furthermore, a simulated gastrointestinal system was employed to predict the impact of digestive processes on As bioavailability. The predominant soluble As species found in all the wines were As(III) and As(v). Based on typical As wine recipes employing 0.1 g realgar mL(-1) wine, the concentration of dissolved As ranged from ca. 100 to 400 mg L(-1) depending on the ethanol content of the preparation: with the As solubility found to be higher in wines with a lower proportion of ethanol. Based on a common 100 mL measure of wine with a concentration of 400 mg As L(-1), the amount of soluble As would equate to around half of the acute minimal lethal dose for adults. This is likely an underestimate of the bioaccessible concentration, as a three-fold increase in bioaccessibility could be observed in the intestinal phase based on the results from the stimulated gastrointestinal system. (C) 2011 Elsevier B.V. All rights reserved.

The Role of Water Content and Paste Proportion on Physico-mechanical Properties of Alkali Activated Fly Ash–Ggbs Concrete

The growth of the construction industry worldwide poses a serious concern on the sustainability of the building material production chain, mainly due to the carbon emissions related to the production of Portland cement. On the other hand, valuable materials from waste streams, particularly from the metallurgical industry, are not used at their full potential. Alkali activated concrete (AAC) has emerged in the last years as a promising alternative to traditional Portland cement based concrete for some applications. However, despite showing remarkable strength and durability potential, its utilisation is not widespread, mainly due to the lack of broadly accepted standards for the selection of suitable mix recipes fulfilling design requirements, in particular workability, setting time and strength. In this paper, a contribution towards the design development of AAC synthetized from pulverised fuel ash (60%) and ground granulated blast furnace slag (40%) activated with a solution of sodium hydroxide and sodium silicate is proposed. Results from a first batch of mixes indicated that water content influences the setting time and that paste content is a key parameter for controlling strength development and workability. The investigation indicated that, for the given raw materials and activator compositions, a minimum water to solid (w/s) ratio of 0.37 was needed for an initial setting time of about 1 hour. Further work with paste content in the range of 30% to 33% determined the relationship between workability and strength development and w/s ratio and paste content. Strengths in the range of 50 - 60 MPa were achieved.