Heller's myotomy and pneumatic dilatation in the treatment of achalasia: a population-based case–control study assessing long-term quality of life

Long-term health-related quality-of-life (HRQL) outcomes have not been widely reported in the
treatment of achalasia. The aims of this study were to examine long-term disease-specific and general HRQL in
achalasia patients using a population-based case–control method, and to assess HRQL between treatment interventions.
Manometrically diagnosed achalasia cases (n = 120) were identified and matched with controls (n = 115)
using a population-based approach. Participants completed general (SF-12) and disease-specific (Achalasia Severity
Questionnaire [ASQ]) HRQL questionnaires, as appropriate, in a structured interview. Mean composite scores
for SF-12 (Mental Component Summary score [MCS-12] and Physical Component Summary score [PCS-12]) and
ASQ were compared between cases and controls, or between intervention groups, using an independent t-test.
Adjusted mean differences in HRQL scores were evaluated using a linear regression model. Achalasia cases were
treated with a Heller’s myotomy (n = 43), pneumatic dilatation (n = 44), or both modalities (n = 33). The median
time from last treatment to HRQL assessment was 5.7 years (interquartile range 2.4–11.5). Comparing achalasia
patients with controls, PCS-12 was significantly worse (40.9 vs. 44.2, P = 0.01), but MCS-12 was similar. However,
both PCS-12 (39.9 vs. 44.2, P = 0.03) and MCS-12 (46.7 vs. 53.5, P = 0.004) were significantly impaired in those
requiring dual treatment compared with controls. Overall however, there was no difference in adjusted HRQL
between patients treated with Heller’s myotomy, pneumatic dilatation or both treatment modalities. In summary,
despite treatment achalasia patients have significantly worse long-term physical HRQL compared with population
controls. No HRQL differences were observed between the treatment modalities to suggest a benefit of one
treatment over another.

Pseudophakic retinal detachment

Pseudophakic retinal detachment is a rare, but potentially serious, complication of cataract surgery. The incidence of pseudophakic retinal detachment following current surgical techniques of cataract extraction, including extracapsular cataract extraction by nuclear expression and phacoemulsification, is lower than that found after intracapsular cataract extraction. The risk of pseudophakic retinal detachment appears to be increased in myopic patients, in those patients in whom vitreous loss had occurred at the time of cataract surgery, and in patients undergoing Nd:YAG posterior capsulotomy. Most cases present to the clinician when the macula is already detached and the central vision is affected. When evaluating patients with pseudophakic retinal detachment, the fundal view is often impaired by anterior or posterior capsular opacification, reflections related to the intraocular lens, or poor mydriasis. Scleral buckling, pneumatic retinopexy, and primary pars plana vitrectomy, with or without combined scleral buckling, are the surgical techniques used to treat pseudophakic retinal detachment. Anatomical success rates are high after vitreo-retinal surgery for pseudophakic retinal detachment, although a smaller proportion of patients recover good vision following surgery. © 2003 Elsevier Inc. All rights reserved.

Achalasia: A review of clinical diagnosis, epidemiology, treatment and outcomes

Achalasia is a neurodegenerative motility disorder of the oesophagus resulting in deranged oesophageal peristalsis and loss of lower oesophageal sphincter function. Historically, annual achalasia incidence rates were believed to be low, approximately 0.5-1.2 per 100000. More recent reports suggest that annual incidence rates have risen to 1.6 per 100000 in some populations. The aetiology of achalasia is still unclear but is likely to be multi-factorial. Suggested causes include environmental or viral exposures resulting in inflammation of the oesophageal myenteric plexus, which elicits an autoimmune response. Risk of achalasia may be elevated in a sub-group of genetically susceptible people. Improvement in the diagnosis of achalasia, through the introduction of high resolution manometry with pressure topography plotting, has resulted in the development of a novel classification system for achalasia. This classification system can evaluate patient prognosis and predict responsiveness to treatment. There is currently much debate over whether pneumatic dilatation is a superior method compared to the Heller's myotomy procedure in the treatment of achalasia. A recent comparative study found equal efficacy, suggesting that patient preference and local expertise should guide the choice. Although achalasia is a relatively rare condition, it carries a risk of complications, including aspiration pneumonia and oesophageal cancer. The risk of both squamous cell carcinoma and adenocarcinoma of the oesophagus is believed to be significantly increased in patients with achalasia, however the absolute excess risk is small. Therefore, it is currently unknown whether a surveillance programme in achalasia patients would be effective or cost-effective.

Water spray cooling of polymers

The cooling process in conventional rotomolding is relatively long due to poor thermal conductivity of plastics. The lack of internal cooling is a major limitation although rapid external cooling is possible. Various internal cooling methodologies have been studied to reduce the cycle time. These include the use of compressed air, cryogenic liquid nitrogen, chilled water coils, and cryogenic liquid carbon dioxide, all of which have limitations. However, this article demonstrates the use of water spray cooling of polymers as a viable and effective method for internal cooling in rotomolding. To this end, hydraulic, pneumatic, and ultrasonic nozzles were applied and evaluated using a specially constructed test rig to assess their efficiency. The effects of nozzle type and different parametric settings on water droplet size, velocity, and mass flow rate were analyzed and their influence on cooling rate, surface quality, and morphology of polymer exposed to spray cooling were characterized. The pneumatic nozzle provided highest average cooling rate while the hydraulic nozzle gave lowest average cooling rate. The ultrasonic nozzle with medium droplet size traveling at low velocity produced satisfactory surface finish. Water spray cooling produced smaller spherulites compared to ambient cooling whilst increasing the cooling rate decreases the percentage crystallinity. © 2011 Society of Plastics Engineers Copyright © 2011 Society of Plastics Engineers.