Electrowetting movement of an aqueous droplet between two three-dimensional electrode surfaces

In an effort to develop a novel electronic paper image display technology based on the electrowetting principle, a 3-D electrowetting cell is designed and fabricated, which consists of two 3-D bent electrodes, each having a horizontal surface made of gold and a vertical surface made of indium tin oxide (ITO) glass as a color display window, a layer of dielectric material on the 3-D electrodes, and a highly fluorinated hydrophobic layer on the surface of the dielectric layer. Results of this work show that an electrowetting-induced motion of an aqueous droplet in immiscible oils can be achieved reversibly across the boundary of the horizontal and vertical surfaces of the 3-D electrode surface. It is also shown that the droplet can maintain its wetting state on a vertical sidewall electrode free of a power supplier when the voltage is removed. This phenomenon may form the basis for color contrast modulation applications, where a power-free image display is required, such as electronic paper display technology in the future. (C) 2009 Society of Photo-Optical Instrumentation Engineers. [DOI: 10.1117/1.3100201]

A note on the prediction of liquid hold-up with the stratified roll wave regime for gas/liquidco-current flow in horizontal pipes.

This note presents a simple model for prediction of liquid hold-up in two-phase horizontal pipe flow for the stratified roll wave (St+RW) flow regime. Liquid hold-up data for horizontal two-phase pipe flow [1, 2, 3, 4, 5 and 6] exhibit a steady increase with liquid velocity and a more dramatic fall with increasing gas rate as shown by Hand et al. [7 and 8] for example. In addition the liquid hold-up is reported to show an additional variation with pipe diameter. Generally, if the initial liquid rate for the no-gas flow condition gives a liquid height below the pipe centre line, the flow patterns pass successively through the stratified (St), stratified ripple (St+R), stratified roll wave, film plus droplet (F+D) and finally the annular (A+D, A+RW, A+BTS) regimes as the gas rate is increased. Hand et al. [7 and 8] have given a detailed description of this progression in flow regime development and definitions of the patterns involved. Despite the fact that there are over one hundred models which have been developed to predict liquid hold-up, none have been shown to be universally useful, while only a handful have proven to be applicable to specific flow regimes [9, 10, 11 and 12]. One of the most intractable regimes to predict has been the stratified roll wave pattern where the liquid hold-up shows the most dramatic change with gas flow rate. It has been suggested that the momentum balance-type models, which give both hold-up and pressure drop prediction, can predict universally for all flow regimes but particularly in the case of the difficult stratified roll wave pattern. Donnelly [1] recently demonstrated that the momentum balance models experienced some difficulties in the prediction of this regime. Without going into lengthy details, these models differ in the assumed friction factor or shear stress on the surfaces within the pipe particularly at the liquid–gas interface. The Baker–Jardine model [13] when tested against the 0.0454 m i.d. data of Nguyen [2] exhibited a wide scatter for both liquid hold-up and pressure drop as shown in Fig. 1. The Andritsos–Hanratty model [14] gave better prediction of pressure drop but a wide scatter for liquid hold-up estimation (cf. Fig. 2) when tested against the 0.0935 m i.d. data of Hand [5]. The Spedding–Hand model [15], shown in Fig. 3 against the data of Hand [5], gave improved performance but was still unsatisfactory with the prediction of hold-up for stratified-type flows. The MARS model of Grolman [6] gave better prediction of hold-up (cf. Fig. 4) but deterioration in the estimation of pressure drop when tested against the data of Nguyen [2]. Thus no method is available that will accurately predict liquid hold-up across the whole range of flow patterns but particularly for the stratified plus roll wavy regime. The position is particularly unfortunate since the stratified-type regimes are perhaps the most predominant pattern found in multiphase lines.

A cephalometric study of class II malocclusions treated with mandibular surgery

INTRODUCTION:

Class II malocclusion is often associated with retrognathic mandible. Some of these problems require surgical correction. The purposes of this study were to investigate treatment outcomes in patients with Class II malocclusions whose treatment included mandibular advancement surgery and to identify predictors of good outcomes.
METHODS:

Pretreatment and posttreatment cephalometric radiographs of 90 patients treated with mandibular advancement surgery by 57 consultant orthodontists in the United Kingdom before September 1998 were digitized, and cephalometric landmarks were identified. Paired samples t tests were used to compare the pretreatment and posttreatment cephalometric values for each patient. For each cephalometric variable, the proportion of patients falling within the ideal range was identified. Multiple logistic regression analysis was performed to identify predictors of achieving ideal range outcomes for the key skeletal (ANB and SNB angles), dental (overjet and overbite), and soft-tissue (Holdaway angle) measurements.
RESULTS:

An overjet within the ideal range of 1 to 4 mm was achieved in 72% of patients and was more likely with larger initial ANB angles. Horizontal correction of the incisor relationship was achieved by a combination of 75% skeletal movement and 25% dentoalveolar change. An ideal posttreatment ANB angle was achieved in 42% of patients and was more likely in females and those with larger pretreatment ANB angles. Ideal soft-tissue Holdaway angles (7 degrees to 14 degrees ) were achieved in 49% of patients and were more likely in females and those with smaller initial SNA angles. Mandibular incisor decompensation was incomplete in 28% of patients and was more likely in females and patients with greater pretreatment mandibular incisor proclination. Correction of increased overbite was generally successful, although anterior open bites were found in 16% of patients at the end of treatment. These patients were more likely to have had initial open bites.
CONCLUSIONS:

Mandibular surgery had a good success rate in normalizing the main dental and skeletal relationships. Less ideal soft-tissue profile outcomes were associated with larger pretreatment SNA-angle values, larger final mandibular incisor inclinations, and smaller final maxillary incisor inclinations. The use of mandibular surgery to correct anterior open bite was associated with poor outcomes.