Post-mortem examination of a wild muntjac from Northern Ireland.

1. Deer are of major concern with regards to impacts on biodiversity, forestry and agriculture as well as human health. The invasive Reeves’ muntjac deer Muntiacus reevesi, native to Asia but established in Great Britain, has recently appeared in the wild in Ireland.

2. The first verified record in the wild in Northern Ireland was confirmed during June 2009 as a result of a road traffic accident near Newtownards, Co. Down. The second record was a culled animal shot in the grounds of Mount Stewart, Co. Down during June 2011.

3. The current report aimed to perform a detailed investigation of the most recently obtained animal to establish a) its age, b) its genetic relationship with the first animal and c) the threat it might pose in terms of carrying endo- or ecto-parasites or other micro-pathogens, principally viruses and bacteria.

4. Analysis of its dentition suggested the culled animal was 56 weeks old (range 55-57 weeks).

5. Genetic analysis indicated that there was no possibility of a father-son relationship with the buck killed in 2009. There was a 6.25% probability of both individuals being full-sibs and a 25% probability of a half-sib relationship.

6. The deer was free from all the major pathogens. Most significantly, a novel species of Gammaherpesvirus was detected most closely matching type 2 ruminant rhadinovirus (Gammaherpesvirinae) from mule deer. Further sequencing is required to provide a definitive classification. There is no evidence suggesting this virus is pathogenic but its detection is nonetheless of concern.

7. During late 2009 (after the first animal was recovered) and early 2010, there were a number of sightings of muntjac within the vicinity of Mount Stewart. Our results indicate that the animal shot in June 2011 could not have been this same animal, as the shot animal must have been born in spring 2010. Moreover, genetic analysis indicates that the two recovered individuals were highly unlikely to share the same mother and father, suggesting they were the offspring of a minimum of three breeding adults (two fathers and one mother or two mothers and one father). This brings the total number of known individuals to 5 including the two offspring. The location of the breeding adults is unknown and may be either in captivity with subsequent escapees, or deliberate releases, or be free living in the wild. However, a further sighting during early 2012 may suggest a wild origin.

Design of an intravaginal ring for the controlled delivery of 17b-estradiol as its 3-acetate ester

Suitable ester prodrugs of 17b-estradiol are identified, thus permitting effective sustained and controlled estrogen replacement therapy (ERT) from an elastomeric, silicone intravaginal ring (IVR). IVR devices of reservoir design were prepared by blending silicone elastomer base with n-propylorthosilicate (cross-linker) and 10% w/w of 17b-estradiol or an ester prodrug, the mix being activated with 0.5% w/w stannous octoate and cured at 808C for 2 min. A rate-controlling membrane was similarly prepared, without the active agent. IVR devices were of cross-sectional diameter 9 mm, outer diameter 54 mm, with core cross-sectional diameter of 2 mm and core length varied as required. Sink conditions were evident for the 17b-estradiol esters in 1.0% aqueous benzalkonium chloride solution. The low release rates into 0.9% w/v saline of the lipophilic valerate and benzoate esters were due to their intrinsically low aqueous solubilities. In vivo, these esters failed to raise plasma estradiol above baseline levels in postmenopausal human volunteers, despite good in vitro release characteristics under sink conditions. The best release rates under sink conditions, in combination with substantial aqueous solubilities as indicated by the release rates into saline, were observed for the acetate and propionate esters. A
combination of drug release characteristics, short plasma half-life and a toxicologically acceptable hydrolysis product indicated that 17b-estradiol-3-acetate was the prodrug of choice for IVR delivery of ERT. In vivo, an IVR device releasing
100 mg/day of estradiol as its 3-acetate ester maintained over 84 days a circulating plasma concentration in the region of 300 pmol l , within the clinically desirable range for ERT.

Integrating allowable design strains in composites with whole life value

Fibre-Reinforced Plastics (FRPs) have been used in civil aerospace vehicles for decades. The current state-of-the-art in airframe design and manufacture results in approximately half the airframe mass attributable to FRP materials. The continual increase in the use of FRP materials over metallic alloys is attributable to the material's superior specific strength and stiffness, fatigue performance and corrosion resistance. However, the full potential of these materials has yet to be exploited as analysis methods to predict physical failure with equal accuracy and robustness are not yet available. The result is a conservative approach to design, but one that can bring benefit via increased inspection intervals and reduced cost over the vehicle life. The challenge is that the methods used in practice are based on empirical tests and real relationships and drivers are difficult to see in this complex process and so the trade-off decision is challenging and uncertain. The aim of this feasibility study was to scope a viable process which could help develop some rules and relationships based on the fundamental mechanics of composite material and the economics of production and operation, which would enhance understanding of the role and impact of design allowables across the life of a composite structure.

Optimal design of long-span steel portal frames using fabricated beams

This paper considers the optimal design of fabricated steel beams for long-span portal frames. The design optimisation takes into account ultimate as well as serviceability limit states, adopting deflection limits recommended by the Steel Construction Institute (SCI). Results for three benchmark frames demonstrate the efficiency of the optimisation methodology. A genetic algorithm (GA) was used to optimise the dimensions of the plates used for the columns, rafters and haunches. Discrete decision variables were adopted for the thickness of the steel plates and continuous variables for the breadth and depth of the plates. Strategies were developed to enhance the performance of the GA including solution space reduction and a hybrid initial population half of which is derived using Latin hypercube sampling. The results show that the proposed GA-based optimisation model generates optimal and near-optimal solutions consistently. A parametric study is then conducted on frames of different spans. A significant variation in weight between fabricated and conventional hot-rolled steel portal frames is shown; for a 50 m span frame, a 14–19% saving in weight was achieved. Furthermore, since Universal Beam sections in the UK come from a discrete section library, the results could also provide overall dimensions of other beams that could be more efficient for portal frames. Eurocode 3 was used for illustrative purposes; any alternative code of practice may be used.