Enhancement of the properties of EPDM/NBR elastomers using nanoclay for seal applications

In this research, we have investigated the effects of addition of different percentages of nanoclay to the ethylene propylene diene monomer (EPDM) and nitrile butadiene rubber (NBR) on the characteristics of these rubbers as seal material. Properties such as tensile strength, modulus at different extensions, elongation at break, compressive set, hardness, and permeability and abrasion resistance are tested to assess the effect of addition of the nanoclay. Results indicate that addition of nanoclay at certain compositions could slightly reduce the strength of the rubber. However more stable modulus at different strains are provided, the hardness of the rubber is preserved and slightly enhanced, the permeability is reduced in both rubbers especially considerable decrease in EPDM is observed which is desirable in diminishing the effect of explosive decompression. At the same time the compression test shows that the nanoclay improves the performance of the rubbers under compression which is essential in seal application. The X-ray diffraction tests clarify that the dispersion of the nanoclay in the NBR samples is of high quality. In the EPDM samples, the dispersion is in need of improvement. POLYM. COMPOS., 30:1657-1667, 2009. © 2008 Society of Plastics Engineers.

Experimental and discrete element modelling of cohesive iron ore fines

In this study, the behaviour of iron ore fines with varying levels of adhesion was investigated using a confined compression test and a uniaxial test. The uniaxial test was conducted using the semi-automated uniaxial EPT tester in which the cohesive strength of a bulk solid is evaluated from an unconfined compression test following a period of consolidation to a pre-defined vertical stress. The iron ore fines were also tested by measuring both the vertical and circumferential strains on the cylindrical container walls under vertical loading in a separate confined compression tester - the K0 tester, to determine the lateral pressure ratio. Discrete Element Method simulations of both experiments were carried out and the predictions were compared with the experimental observations. A recently developed DEM contact model for cohesive solids, an Elasto-Plastic Adhesive model, was used. This particle contact model uses hysteretic non-linear loading and unloading paths and an adhesion parameter which is a function of the maximum contact overlap. The model parameters for the simulations are phenomenologically based to reproduce the key bulk characteristics exhibited by the solid. The simulation results show a good agreement in capturing the stress history dependent behaviour depicted by the flow function of the cohesive iron ore fines while also providing a reasonably good match for the lateral pressure ratio observed during the confined compression K0 tests. This demonstrates the potential for the DEM model to be used in the simulation of bulk handling applications.

Postbuckling behaviour of a blade-stiffened composite panel loaded in uniaxial compression

The postbuckling behaviour of a panel with blade-stiffeners incorporating tapered flanges was experimentally investigated. A new failure mechanism was identified for this particular type of stiffener. Failure was initiated by mid-plane delamination at the free edge of the postbuckled stiffener web at a node-line. This was consistent with an interlaminar shear stress failure and was calculated from strain gauge measurements using an approximate analysis based on lamination theory and incorporating edge effects. The critical shear stress was found to agree well with the shear strength obtained from a three-point bending test of the web laminate. 

Direction-contingent duration compression is primarily retinotopic

Previous research has shown that prior adaptation to a spatially circumscribed, oscillating grating results in the duration of a subsequent stimulus briefly presented within the adapted region being underestimated. There is an on-going debate about where in the motion processing pathway the adaptation underlying this distortion of sub-second duration perception occurs. One position is that the LGN and, perhaps, early cortical processing areas are likely sites for the adaptation; an alternative suggestion is that visual area MT+ contains the neural mechanisms for sub-second timing; and a third position proposes that the effect is driven by adaptation at multiple levels of the motion processing pathway. A related issue is in what frame of reference – retinotopic or spatiotopic – does adaptation induced duration distortion occur. We addressed these questions by having participants adapt to a unidirectional random dot kinematogram (RDK), and then measuring perceived duration of a 600 ms test RDK positioned in either the same retinotopic or the same spatiotopic location as the adaptor. We found that, when it did occur, duration distortion of the test stimulus was direction contingent; that is it occurred when the adaptor and test stimuli drifted in the same direction, but not when they drifted in opposite directions. Furthermore the duration compression was evident primarily under retinotopic viewing conditions, with little evidence of duration distortion under spatiotopic viewing conditions. Our results support previous research implicating cortical mechanisms in the duration encoding of sub-second visual events, and reveal that these mechanisms encode duration within a retinotopic frame of reference.