EVALUATION OF A FOAM BUFFER TARGET DESIGN FOR SPATIALLY UNIFORM ABLATION OF LASER-IRRADIATED PLASMAS

Experimental observations are presented demonstrating that the use of a gold-coated foam layer on the surface of a laser-driven target substantially reduces its hydrodynamic breakup during the acceleration phase. The data suggest that this results from enhanced thermal smoothing during the early-time imprint stage of the interaction. The target's kinetic energy and the level of parametric instability growth are shown to remain essentially unchanged from that of a conventionally driven target.

EMISSION STUDIES OF THE PLUME PRODUCED DURING YBA2CU3O7 FILM PRODUCTION BY LASER-ABLATION

The optical plume emissions produced on excimer laser ablation of a YBa2Cu3O7 target are reported and identified with the various atomic, ionic, and molecular species present. The spatial and temporal distribution of these emissions were studied as a function of the laser fluence and oxygen pressure. At the laser fluences used (4-6 J/cm(2)) some target material is ablated or evaporated directly in molecular form. In addition efficient formation of molecular oxides is observed at the contact front of the expanding plume with the surrounding oxygen atmosphere. The intensity and spatial distribution of oxide emission in the visible plume therefore provides a sensitive diagnostic for optimization of substrate location and deposition conditions.

YBACUO PRBACUO MULTILAYERS BY EXCIMER LASER ABLATION

YBaCuO films with (001) orientation have been deposited on MgO by laser ablation at 248 and 193 nm wavelengths. Transitions to zero resistance at 87 K and 90 K have been reproducibly achieved in the respective cases. Optical spectroscopic studies of the plume show the importance of molecular species in the ablation if good superconducting films are to be formed. The substrate position in the plume and substrate temperature are important in determining film quality. The influence of oxygen gas pressure can be significant. SEM studies show the occurrence of second-phase outcrops with a needle-like morphology aligned over the whole area of the film along two mutually perpendicular directions on the film surface. Film orientation is determined by XRD and R against T is measured down to 80 K in a hydrogen exchange gas cryostat. Characterization studies of device-related multilayer YBaCuO/PrBaCuO structures by XRD are presented.

SUPERCONDUCTING YBA2CU3O7 THIN-FILMS ON MGO BY KRF LASER ABLATION - OPTIMIZATION OF DEPOSITION PARAMETERS

The optimization of interrelated deposition parameters during deposition of in situ YBa2Cu3O7 thin films on MgO substrates by KrF laser ablation was systematically studied in a single experimental chamber. The optimum condition was found to be a substrate temperature of 720-degrees-C and a target-substrate distance of 5 cm in an oxygen partial pressure of 100 mTorr. These conditions produced films with T(c) = 87 K. The presence of YO in the plasma plume was found to be important in producing good quality films. The films were characterized by resistance-temperature measurements, energy dispersive x-ray analyses, scanning electron microscopy, and x-ray-diffraction measurements, and the physical reasons underlying film quality degradation at parameter values away from optimal are discussed.

Application of surface plasmon polaritons in the laser ablation and characterisation of thin aluminium films

Surface modification of thin aluminium films is both produced and characterised by exciting surface plasmon polaritons in an attenuated total reflection geometry: silica prism/aluminium/aluminium oxide system. The modification is performed, under ambient conditions, by exposure to a low fluence (

Contrasting damage characteristics in direct incidence and surface plasmon mediated single-shot laser ablation of aluminium films

Thin, oxidised Al films grown an one face of fused silica prisms are exposed. tinder ambient conditions, to single shots from an excimer laser operating at wavelength 248 nm. Preliminary characterisation of the films using attenuated total reflection yields optical and thickness data for the Al and Al oxide layers; this step facilitates the subsequent, accurate tuning of the excimer laser pulse to the: surface plasmon resonance at the Al/(oxide)/air interface and the calculation of the fluence actually absorbed by the thin film system. Ablation damage is characterised using scanning electron, and atomic force microscopy. When the laser pulse is incident, through the prism on the sample at less than critical angle, the damage features are molten in nature with small islands of sub-micrometer dimension much in evidence, a mechanism of film melt-through and subsegment blow-off due to the build up of vapour pressure at the substrate/film interface is appropriate. By contrast, when the optical input is surface plasmon mediated, predominately mechanical damage results with the film fragmenting into large flakes of dimensions on the order of 10 mu m. It is suggested that the ability of surface plasmons to transport energy leads to enhanced, preferential absorption of energy at defect sites causing stress throughout the film which exceeds the ultimate tensile stress for the film: this in turn leads to film break-up before melting can onset. (C) 1998 Elsevier Science B.V.

SURFACE-PLASMON ENHANCED LASER-ABLATION OF THIN METAL-FILMS

Surface plasmon enhancement of laser ablation of thin Al films is examined with a view to its application in metal film patterning and nano-structuring. Al films, deposited on silica prisms, are first characterized by attenuated total reflection using a broadband UV source and appropriate interference filter. The films are subsequently subjected to excimer laser radiation of wavelength 248 nm under conditions both of direct incidence from the air side of the film, and of surface plasmon excitation in which light is incident through the prism at greater than critical angle. For a given level of ablation damage in a particular film the fluence required using the surface plasmon technique is 3-5 times less than that needed when direct incidence is used. This is roughly in line with the energy absorbed in the film. From a practical standpoint it is clear that ablation of metal films can be achieved with much lower fluences than has hitherto been possible, thus reducing the requirements on laser output and relaxing the power handling constraints on any input optical elements.