The effect of anisotropic elasticity on the yielding characteristics of overconsolidated natural clay

Quantitative application of elastoplastic theory to the yielding behaviour of natural soils has always been uncertain. Part of the reason is that the theory was developed for reconstituted materials with isotropic structure, in contrast to natural soils that are usually anisotropic. The approach considered in this study assumes that pre-yielding behaviour is governed by the theory of linear anisotropic elasticity and that yield loci in the mean effective stress ( p') – deviator stress (q) plane are aligned approximately along the coefficient of earth pressure (K0) line. The assumption of a rotated yield locus associated with anisotropic elastic behaviour within the state boundary surface indicates that the elastic wall within the state boundary surface is inclined. The form of the state boundary surface has been determined mathematically in terms of anisotropic elastic and Cam-Clay soil parameters. Stress path tests were conducted on samples of Belfast Upper Boulder Clay removed from a depth of 28 m below ground surface. Good agreement was found between predicted and measured yield loci. The study also examined the influence of subsequent isotropic compression on the yielding characteristics of the natural clay. The indications are that the anisotropy developed during deposition disappears when the sample is loaded to a stress level at least twice the stress generated during the original deposition process. The methods developed in the paper have also been applied to test results reported previously on Winnipeg clay, and good agreement was obtained.

Synthesis of nucleoside analogues in a ball mill: fast, chemoselective and high yielding acylation without undesirable solvents

The chemoselective acylation of primary aliphatic amines has been achieved in under ten minutes (and for aromatic amines under 120 min) using vibration ball-milling, avoiding undesirable solvents which are typically employed for such reactions (e.g. DMF). Under optimised conditions, the synthesis of amides in the presence of both primary and secondary alcohol functions was achieved in high to excellent yields (65-94%). Overall, the methods described have significant practical advantages over conventional approaches based upon bulk solvents including greater yields, higher chemoselectivity and easier product separation.

An evaluation of the effect of altering nutrition and nutritional strategies in early lactation on reproductive performance and estrous behavior of high-yielding Holstein-Friesian dairy cows

Reproductive performance in the high-yielding dairy cow has severely decreased in the last 40 yr. The aim of this study was to compare the effectiveness of 4 nutritional strategies in improving the reproductive performance of high-yielding dairy cows. It was hypothesized that offering cows a high-starch ration in early lactation would enhance the onset of luteal activity, and that decreasing the severity of negative energy balance in the early postcalving period would improve reproductive parameters. Nutritional regimens aimed at improving fertility were applied to 96 Holstein-Friesian dairy animals. Upon calving, animals were allocated in a balanced manner to one of 4 dietary treatments. Primiparous animals were balanced according to live weight, body condition score and calving date. Multiparous animals were balanced according to parity, previous lactation milk yield, liveweight, body condition score and calving date. Treatment 1 was based on an industry best practice diet (control) to contain 170 g of crude protein/kg of dry matter. Treatment 2 was an individual cow feeding strategy, whereby the energy balance (EB) of individual animals was managed so as to achieve a predetermined target daily EB profile (+/- 10 MJ/d). Treatment 3 was a high-starch/high-fat combination treatment, whereby an insulinogenic (high-starch) diet was offered in early lactation to encourage cyclicity and followed by a lipogenic (low-starch, high-fat) diet to promote embryo development. Treatment 4 was a low-protein diet, containing 140 g of crude protein/kg of dry matter, supplemented with protected methionine at an inclusion level of 40 g per animal per day. The nutritional strategies implemented in this study had no statistically significant effects on cow fertility measures, which included the onset of luteal activity, conception rate, in-calf rate, and the incidence of atypical cycles. The individual cow feeding strategy improved EB in early lactation but had no benefit on conception rate to first insemination. However, conception rate to second insemination, 100-d pregnancy rate (from the commencement of breeding), and overall pregnancy rate tended to be higher in this group. The high-starch/high-fat treatment tended to decrease the proportion of delayed ovulations and increase the proportion of animals cycling by d 50 postcalving. Animals that failed to conceive to first insemination had a significantly longer luteal phase in the first cycle postpartum and a longer inter-ovulatory interval in the second cycle postpartum. With regards to estrous behavior, results indicate that as the size of the sexually active group increased, the intensity of estrus and the expression of mounting or attempting to mount another cow also increased. Furthermore, cows that became pregnant displayed more intense estrous behavior than cows that failed to become pregnant.

Accounting for clean, fast and high yielding reactions under microwave conditions

Thermal reactions proceed optimally when they are rapidly heated to the highest tolerable temperature, held there for the shortest possible time and then quenched. This is explained through assessments of reaction kinetics in literature examples and models. Although presently available microwave equipment is better suited to rapid heating than resistance-heated systems, the findings do not depend upon the method of heating. Claims that microwave heated reactions proceed faster and more cleanly than their conventionally heated counterparts are valid only when comparably rapid heating and cooling cannot be obtained by conventional heating. These findings suggest that rigid adherence to the sixth principle of green chemistry, relating to the use of ambient temperature and pressure, may not always afford optimal results. © 2010 The Royal Society of Chemistry.

Design of a silicone reservoir intravaginal ring for the delivery of oxybutynin.

Oxybutynin, a drug of choice in the treatment of urinary incontinence, has low oral bioavailability due to extensive first-pass metabolism. A toxic metabolite, N-desethyloxybutynin, has been linked to adverse reactions to oral oxybutynin. This study, therefore, reports on the design of an oxybutynin intravaginal ring (IVR) of reservoir design, comprising an oxybutynin silicone elastomer core encased in a non-medicated silicone sheath, manufactured by reaction injection moulding at 50oC. An unusually high initial burst release of oxybutynin (42.7 mg in 24 h) was observed in vitro with a full length core (100 mg drug loading), with subsequent non-zero order drug release. Use of fractional segment cores substantially reduced the burst effect, yielding linear cumulative drug release versus time plots from days 2 to 14. Thus, a 1/8 fractional segment core gave a 24 h burst of 11.28 mg oxybutynin and, thereafter, zero order release at the target dose of 5 mg/day over 14 days. Two oxybutynin cores, each 1/16 of full length, gave a greater release than a single 1/8 core, due to core segment end effects resulting in an increased surface area for release. The burst release was investigated by determining drug solubilities in the propan-1-ol product of elastomer condensation cure (390 mg/ml) and in the elastomer itself (13.9-20.21 mg/ml, by direct extraction and indirect thermal methods). These high oxybutynin solubilities were considered the major contributors to the burst effect. It was concluded that use of a fractional segment core would allow development of a suitable oxybutynin reservoir IVR.

What motion distributions yield global transparency and spatial segmentation?

We have examined the ability of observers to parse bimodal local-motion distributions into two global motion surfaces, either overlapping (yielding transparent motion) or spatially segregated (yielding a motion boundary). The stimuli were random dot kinematograms in which the direction of motion of each dot was drawn from one of two rectangular probability distributions. A wide range of direction distribution widths and separations was tested. The ability to discriminate the direction of motion of one of the two motion surfaces from the direction of a comparison stimulus was used as an objective test of the perception of two discrete surfaces. Performance for both transparent and spatially segregated motion was remarkably good, being only slightly inferior to that achieved with a single global motion surface. Performance was consistently better for segregated motion than for transparency. Whereas transparent motion was only perceived with direction distributions which were separated by a significant gap, segregated motion could be seen with abutting or even partially overlapping direction distributions. For transparency, the critical gap increased with the range of directions in the distribution. This result does not support models in which transparency depends on detection of a minimum size of gap defining a bimodal direction distribution. We suggest, instead, that the operations which detect bimodality are scaled (in the direction domain) with the overall range of distributions. This yields a flexible, adaptive system that determines whether a gap in the direction distribution serves as a segmentation cue or is smoothed as part of a unitary computation of global motion.

Performance assessment of nanoscale double- and triple- gate FinFETs

This is the first paper to describe performance assessment of triple and double gate FinFETs for High Performance (HP), Low Operating Power (LOP) and Low Standby Power (LSTP) logic technologies is investigated. The impact of gate work-function, spacer width, lateral source/drain doping gradient, fin aspect ratio, fin thickness on device performance, has been analysed in detail and guidelines are presented to meet ITRS specification at 65 and 45 nm nodes. Optimal design of lateral source/drain doping profile can not only effectively control short channel effects, yielding low off-current, but also achieve low values of intrinsic gate delay.

Deep sampling and testing in soft stratified clay

A 37-m thick layer of stratified clay encountered during a site investigation at Swann's Bridge, near the sea-coast at Limavady, Northern Ireland, is one of the deepest and thickest layers of this type of material recorded in Ireland. A study of the relevant literature and stratigraphic evidence obtained from the site investigation showed that despite being close to the current shoreline, the clay was deposited in a fresh-water glacial lake formed approximately 13 000 BP. The 37-m layer of clay can be divided into two separate zones. The lower zone was deposited as a series of laminated layers of sand, silt, and clay, whereas the upper zone was deposited as a largely homogeneous mixture. A comprehensive series of tests was carried out on carefully selected samples from the full thickness of the deposit. The results obtained from these tests were complex and confusing, particularly the results of tests done on samples from the lower zone. The results of one-dimensional compression tests, unconsolidated undrained triaxial tests, and consolidated undrained triaxial compression tests showed that despite careful sampling, all of the specimens from the lower zone exhibited behaviour similar to that of reconstituted clays. It was immediately clear that the results needed explanation. This paper studies possible causes of the results from tests carried out on the lower Limavady clay. It suggests a possible mechanism based on anisotropic elasticity, yielding, and destructuring that provides an understanding of the observed behaviour.Key words: clay, laminations, disturbance, yielding, destructuring, reconstituted.

Opacity in the upper atmosphere of AU Mic

In this paper we investigate the validity of the optically thin assumption in the transition region of the late-type star AU Mic. We use Far-Ultraviolet Spectroscopic Explorer (FUSE) observations of the C III multiplet and O VI resonance lines, hence yielding information at two different levels within the atmosphere. Significant deviations from the optically thin fluxes are found for C III in both quiescent and flare spectra, where only 60% of the flux is actually observed. This could explain the apparent deviation of C III observed in emission measure distributions. We utilize escape probabilities for both homogeneous and inhomogeneous geometries and calculate optical depths as high as 10 for the C III 1175.71 Angstrom component of the multiplet. Using a lower limit to the electron density (10(11) cm(-3))we derive an effective thickness of

Light emission from scanning tunnelling microscope on polycrystalline Au films - what is happening at the single-grain level?

When operated with a metallic tip and sample the scanning tunnelling microscope constitutes a nanoscale, plasmonic light source yielding broadband emission up to a photon energy determined by the applied bias. The emission is due to tunnelling electron excitation and subsequent radiative decay of localized plasmon modes, which can be on the lateral scale of a single metal grain (similar to 25 nm) or less. For a Au-tip/Au-polycrystalline sample under ambient conditions it is found that the intensity and spectral content of the emitted light are not dependent on the lateral grain dimension, but are predominantly determined by the tip geometry. However, the intensity increases strongly with increasing film thickness (grain depth) up to 20-25 nm or approximately the skin depth of the Au film. Photon maps can show less emissive grains and two classes of this occurrence are distinguished. The first is geometrical in origin - a double-tip structure in this case - while the second is due to a contamination-induced lowering of the local work function that causes the tunnel gap to increase. It is suggested that differences in work-function lowering between grains presenting different crystalline facets, combined with an exponential decay in emitted light intensity with tip - sample distance, leads to grain contrast. These results are relevant to tip-enhanced Raman scattering and the fabrication of micro/nano-scale planar, light-emitting tunnel devices.

Investigations on the adsorption of acidic gases using activated dolomite

In this work activated dolomite adsorption was investigated for removal of acidic gaseous pollutants. Charring was found to be an effective method for the activation of dolomite. This thermal processing resulted in partial decomposition, yielding a calcite and magnesium oxide structure. Adsorbents were produced over a range of char temperatures (750, 800 and 850 °C) and char times (1–8 h). The surface properties and the adsorption capability of raw and thermally treated dolomite sorbents were investigated using porosimetry, SEM and XRD. The sorbates individually investigated were CO2 and NO2. Volumetric equilibrium isotherm determinations were produced in order to quantify sorbate capacity on the various sorbents. The equilibrium data were successfully described using the Freundlich isotherm model. Despite relatively low surface area characteristics of the activated dolomite, there was a high capacity for the acidic gas sorbates investigated, showing a maximum of 12.6 mmol/g (554 mg/g) for CO2 adsorption and 9.93 mmol/g (457 mg/g) for NO2 adsorption. Potentially the most cost effective result from the work concerns the adsorptive capacity for the naturally occurring material, which gave a capacity of 9.71 mmol/g (427 mg/g) for CO2 adsorption and 4.18 mmol/g (193 mg/g) for NO2 adsorption. These results indicate that dolomitic sorbents are potentially cost effective materials for acidic gases adsorption.

Applying an Agility/Discipline Assessment for a Small Software Organisation

The adoption of agile software development methodologies may appear to be a rather straightforward process yielding instantly improved software in less time and increasingly satisfied customers. This paper will show that such a notion is a misunderstanding and can be harmful to small software development organisations. A more reasonable approach involves a careful risk assessment and framework for introducing agile practices to address specific risks. A case study with a small software development organisation is provided to show the assessment in practice and the resulting risk mitigation strategies for process improvement.

Laser annealing of sputtered silicon for wafer-bonding applications

Sputtered silicon is investigated as a bonding layer for transfer of pre-processed silicon layers to various insulating substrates. Although the material appears suitable for low temperature processing, previous work has shown that gas trapped in the pores of the sputtered material is released at temperatures above 350 degrees C and further increases of temperature lead to destruction of any bonded interface. Pre-annealing at 1000 degrees C before bonding drives out gas and/or seals the surface, but for device applications where processing temperatures must be kept below about 300 degrees C, this technique cannot be used. In the current work, we have investigated the effect of excimer laser-annealing to heat the sputtered silicon surface to high temperature whilst minimising heating of the underlying substrate. Temperature profile simulations are presented and the results of RBS, TEM and AFM used to characterise the annealed layers. The results verify that gases are present in the sub-surface layers and suggest that while sealing of the surface is important for suppression of the out-diffusion of gases, immediate surface gas removal may also play a role. The laser-annealing technique appears to be an effective method of treating sputtered silicon, yielding a low roughness surface suitable for wafer bonding, thermal splitting and layer transfer.

Optical diagnostics of micro discharge jets

Micro plasmas operated at ambient pressure with dimensions of the confining geometry in the order of a few ten micrometers to a millimeter are actually in the focus of interest due to the broad regime of applicability they offer and due to a similarly broad range of open physical questions. Here we present optical measurements within the discharge core and the effluent region of an especially developed micro discharge jet. To get an understanding of the complex system of this discharge it is important to analyse transport phenomena of energy and particles within both parts of the discharge by various highly sophisticated diagnostics. As a consequence of the limited access and the dimensions of the micro discharge most of these diagnostics are optical. Here we present diagnostics applied to determine spatially resolved absolute atomic oxygen densities as the most reactive constituent of the effluent, density maps of ozone as final reaction product of the gas chemical chain induced by the discharge and phase resolved optical emission spectroscopy yielding insight into the excitation dynamics of the discharge. (C) 2007 WILEY-VCH Verlag GmbH & Co. KGaA. Weinheim.

Two-electron QED contributions to the ground-state binding energy in He-like Kr34+ ions

The two-electron QED contributions to the ground-state binding energy of Kr34+ ions have been determined in two independent experiments performed with electron beam ion traps (EBIT) in Heidelberg (HD) and Tokyo (BT, Belfast-Tokyo collaboration). X rays arising from radiative recombination (RR) of free electrons to the ground state of initially bare Kr36+ and hydrogenlike Kr35+ ions were observed as a function of the interacting electron energy. The K edge absorption by thin Eu and W foils provided fixed photon energy references used to measure the difference in binding energy Delta E-2e between the H- and He-like Kr ions (Kr35+ and Kr34+, respectively). The two values agree well, yielding a final result of Delta E-2e=641.8 +/- 1.7 eV, confirming recent results of rigorous QED calculations. This accuracy is just of the order required to access screened radiative QED contributions.