Comparative study of tool life and hole quality in drilling of CFRP/titanium stack using coated carbide drill

The use of hybrid materials including carbon fiber reinforced plastics (CFRPs) and lightweight metals such as titanium are increasing particularly in aerospace applications. Multi-material stacks require a number of holes for the assembly purposes. In this research, drilling trials have been carried out in CFRP, Ti-6Al-4V and CFRP/Ti-6Al-4V stack workpieces using AlTiN coated tungsten carbide drill bit. The effects of process parameters have been investigated. The thrust force, torque, burr formation, delamination, surface roughness and tool wear have been analyzed at various processing condition. The experimental results have shown that the thrust force, torque, burr formation and the average surface roughness increase with the increased feed rate and decrease with the increased cutting speed in drilling of Ti-6Al-4V. In drilling CFRP, delamination and the average surface roughness has similar tendency with the cutting parameters however thrust force and torque rises with the increased cutting speed. The results showed that after making 15 holes in CFRP/Ti-6Al-4V stack, measured thrust forces were increased by 20% in CFRP and by 45% in Ti-6Al-4V. Delamination was found to be much smaller in drilling of CFRP in stack from compared to drilling single CFRP. Tool life was significantly shortened in drilling of stack due to the combination of the wear mechanisms.

Tool life and hole surface integrity studies for hole-making of Ti6Al4V Alloy

With a significant growth in the use of titanium alloys in the aviation manufacturing industry, the key challenge of making high-quality holes in the aircraft assembly process needs to be addressed. In this work, case studies deploying traditional drilling and helical milling technologies are carried out to investigate the tool life and hole surface integrity for hole-making of titanium alloy. Results show that the helical milling process leads to much longer tool life, generally lower hole surface roughness, and higher hole subsurface microhardness. In addition, no plastically deformed layer or white layer has been observed in holes produced by helical milling. In contrast, a slightly softened region was always present on the drilled surface. The residual stress distributions within the hole surface, including compressive and tensile residual stress, have also been investigated in detail.

FEM Analysis to Optimally Design End Mill cutters for Milling of Ti-6Al-4V

This paper presents an FEM analysis conducted for optimally designing end mill cutters through verifying the cutting tool forces and stresses for milling Titanium alloy Ti-6Al-4 V. Initially, the theoretical tool forces are calculated by considering the cutting edge on a cutting tool as the curve of an intersection over a spherical/flat surface based on the model developed by Lee & Altinas [1]. Considering the lowest tool forces the cutting tool parameters are taken and optimal design of end mill is decided for different sizes. Then the 3D CAD models of the end mills are developed and used for Finite Element Method to verify the cutting forces for milling Ti-6Al-4 V. The cutting tool forces, stress, strain concentration (s), tool wear, and temperature of the cutting tool with the different geometric shapes are simulated considering Ti-6Al-4 V as work piece material. Finally, the simulated and theoretical values are compared and the optimal design of cutting tool for different sizes are validated. The present approach considers to improve the quality of machining surface and tool life with effects of the various parameters concerning the oblique cutting process namely axial, radial and tangential forces. Various simulated test cases are presented to highlight the approach on optimally designing end mill cutters.

Measuring health-related quality of life after stroke: A brief tool.

Routine assessment of health-related quality of life (HRQoL) can be time consuming and burdensome for a person with stroke. Therefore the aim of this study was to develop and test a brief instrument for assessing HRQoL among people with stroke. The Quality of Life after Stroke Scale (QLASS) was constructed from items within the Quality of Life Index-Stroke Version and the Chronic Respiratory Disease Questionnaire. It was administered to 92 people with stroke at three points in time: immediately after discharge from hospital, 6 months and 12 months later. Results suggest that the QLASS has 19 items which represent three factors: emotional functioning, mastery and fatigue which correlate with valid measures of health status and activities of daily living. The QLASS is proposed as a brief, valid HRQoL tool for use among people with stroke.

Assessing quality of life in cardiac rehabilitation: Choosing an appropriate tool

Quality of life is an important outcome for people undergoing cardiac rehabilitation. This paper discusses the difficulties with defining the concept of quality of life and how it might be distinct from the concept of health-related quality of life. Based on a review of the literature, a description is provided of health-related quality of life questionnaires that have been used in cardiac rehabilitation populations. Some criteria for choosing between these questionnaires are then discussed and, finally, a brief discussion is presented of the concept of response shift and how this might influence the assessment of health-related quality of life in a cardiac rehabilitation setting.

A streamlined life-cycle assessment and decision tool for used tyres recycling

In order to achieve progress towards sustainable resource management, it is essential to evaluate options for the reuse and recycling of secondary raw materials, in order to provide a robust evidence base for decision makers. This paper presents the research undertaken in the development of a web-based decision-support tool (the used tyres resource efficiency tool) to compare three processing routes for used tyres compared to their existing primary alternatives. Primary data on the energy and material flows for the three routes, and their alternatives were collected and analysed. The methodology used was a streamlined life-cycle assessment (sLCA) approach. Processes included were: car tyre baling against aggregate gabions; car tyre retreading against new car tyres; and car tyre shred used in landfill engineering against primary aggregates. The outputs of the assessment, and web-based tool, were estimates of raw materials used, carbon dioxide emissions and costs. The paper discusses the benefits of carrying out a streamlined LCA and using the outputs of this analysis to develop a decision-support tool. The strengths and weakness of this approach are discussed and future research priorities identified which could facilitate the use of life cycle approaches by designers and practitioners.

Boost your word power: Katherine Rogers and Maggie Bennett describe a tool that can help students prepare their life science assignments

Anatomy and physiology refers to the structure and function of the human body. Students studying this module, known as life science or bioscience, develop knowledge of the structure (anatomy) and function (physiology) of the body that can be applied in clinical practice and support other study courses.

STOPPFrail (Screening Tool of Older Persons Prescriptions in Frail Adults with Limited Life Expectancy): Consensus Validation

Background: To validate STOPPFrail, a list of explicit criteria for potentially inappropriate medications (PIMs) in frailer older adults with limited life expectancy. A Delphi consensus survey of an expert panel (n = 17) comprising specialists in geriatric medicine, clinical pharmacology, palliative care, psychiatry of old age, clinical pharmacy and general practice.
Methods: STOPPFrail criteria was initially created by the authors based on clinical
experience and appraisal of the available literature. Criteria were organised according to physiological system. Each criterion was accompanied by an explanation. Panellists ranked their agreement with each criterion on a 5-point Likert scale and invited to provide written feedback. Criteria with a median Likert response of 4/5 (agree/strongly agree) and a 25th centile of ≥4 were included in the final criteria.
Results: Three Delphi rounds were required. All panellists completed all rounds. Thirty criteria were proposed for inclusion; 26 were accepted. No new criteria were added. The first two criteria suggest deprescribing medications with no indication or where compliance is poor. The remaining 24 criteria include lipid-lowering therapies, alpha-blockers for hypertension, anti-platelets, neuroleptics, proton pump inhibitors, H-2 receptor antagonists, anti-spasmodics, theophylline, leukotriene antagonists, calcium supplements, bone anti-resorptive therapy, selective oestrogen receptor modulators, non-steroidal antiinflammatories, corticosteroids, 5-alpha reductase inhibitors, alpha-1 selective blockers, muscarinic antagonists, oral diabetic agents, ACE-inhibitors, angiotensin receptor blockers, systemic oestrogens, multivitamins, nutritional supplements and prophylactic antibiotics. Anticoagulants and anti-depressants were excluded. Despite incorporation of panellists’ suggestions, memantine and acetyl-cholinesterase inhibitors remained inconclusive.
Conclusion: STOPPFrail comprises 26 criteria, which have been judged by broad consensus, to be potentially inappropriate in frailer older patients with limited life expectancy. STOPPFrail may assist in deprescribing medications in these patients.

A generic tool for cost estimating in aircraft design

A methodology to estimate the cost implications of design decisions by integrating cost as a design parameter at an early design stage is presented. The model is developed on a hierarchical basis, the manufacturing cost of aircraft fuselage panels being analysed in this paper. The manufacturing cost modelling is original and relies on a genetic-causal method where the drivers of each element of cost are identified relative to the process capability. The cost model is then extended to life cycle costing by computing the Direct Operating Cost as a function of acquisition cost and fuel burn, and coupled with a semi-empirical numerical analysis using Engineering Sciences Data Unit reference data to model the structural integrity of the fuselage shell with regard to material failure and various modes of buckling. The main finding of the paper is that the traditional minimum weight condition is a dated and sub-optimal approach to airframe structural design.

Wear analysis and prediction of the life of a riveting die used in the automotive industry

Knowledge on the life span of the riveting dies used in the automotive industry is sparse. It is often the case that only when faulty products are produced are workers aware that their tool needs to be changed. This is of course costly both in terms of time and money. Responding to this challenge, this paper proposes a methodology which integrates wear and stress analysis to quantify the life of a riveting die. Experiments are carried out to measure the applied load required to split a rivet. The obtained results (i.e. force curves) are used to validate the wear mechanisms of the die observed using scanning electron microscopy. Sliding, impact, and adhesive wears are observed on the riveting die after a certain number of riveting cycles. The stress distribution on the die during riveting is simulated using a finite element (FE) approach. In order to confirm the accuracy of the FE model, the experimental force results are compared with the ones produced from FE simulation. The maximum and minimum von Mises' stresses generated from the FE model are input into a Goodman diagram and an S-N curve to compute the life of the riveting die. It is found that the riveting die is predicted to run for 4 980 000 cycles before failure.

Women, letter-writing and the life of the mind in England, c.1650-1750

Drawing on national and regional letter collections dating from the late seventeenth and early eighteenth centuries, this article explores women's experiences of the life of the mind through an analysis of their letter-writing. This study also highlights the shortcomings of the compartmentalised nature of scholarship on women's writing and intellectual lives and proposes the letter both as a beneficial historical source and methodological tool for research on women's mental worlds. By employing an inclusive definition of intellectual and creative life, and eschewing traditional benchmarks of achievement, this article contends that women took a full part in the cultures of knowledge of their time. 

The subjective numeracy scale as a tool for assessing statistical numeracy in older adult populations

BACKGROUND:
Statistical numeracy, necessary for making informed medical decisions, is reduced among older adults who make more decisions about their medical care and treatment than at any other stage of life. Objective numeracy scales are a source of anxiety among patients, heightened among older adults.
OBJECTIVE:
We investigate the subjective numeracy scale as an alternative tool for measuring statistical numeracy with older adult samples.
METHODS:
Numeracy was assessed using objective measures for 526 adults ranging in age from 18 to 93 years, and all participants provided subjective numeracy ratings.
RESULTS:
Subjective numeracy correlated highly with objective measurements among oldest adults (70+ years; r = 0.51, 95% CI 0.32, 0.66), and for younger age groups. Subjective numeracy explained 33.2% of age differences in objective numeracy.
CONCLUSION:
The subjective numeracy scale provides an effective tool for assessing statistical numeracy for broad age ranges and circumvents problems associated with objective numeracy measures.

Myeloproliferative neoplasm patient symptom burden and quality of life: evidence of significant impairment compared to controls

The myeloproliferative neoplasms (MPN) including polycythaemia vera (PV), essential thrombocythaemia and primary myelofibrosis (PMF) are rare diseases contributing to significant morbidity. Symptom management is a prime treatment objective but current symptom assessment tools have not been validated compared to the general population. The MPN-symptom assessment form (MPN-SAF), a reliable and validated clinical tool to assess MPN symptom burden, was administered to MPN patients (n = 106) and, for the first time, population controls (n = 124) as part of a UK case–control study. Mean symptom scores were compared between patients and controls adjusting for potential confounders. Mean patient scores were compared to data collected by the Mayo Clinic, USA on 1,446 international MPN patients to determine patient group representativeness. MPN patients had significantly higher mean scores than controls for 25 of the 26 symptoms measured (P < 0.05); fatigue was the most common symptom (92.4% and 78.1%, respectively). Female MPN patients suffered worse symptom burden than male patients (P < 0.001) and substantially worse burden than female controls (P < 0.001). Compared to the Mayo clinic patients, MPN-UK patients reported similar symptom burden but lower satiety (P = 0.046). Patients with PMF reported the worst symptom burden (88.3%); significantly higher than PV patients (P < 0.001). For the first time we report quality of life was worse in MPN-UK patients compared with controls (P < 0.001).

'Talk to me': a mixed methods study on preferred physician behaviours during end-of-life communication from the patient perspective

Background
Despite the recognized importance of end-of-life (EOL) communication between patients and physicians, the extent and quality of such communication is lacking.

Objective
We sought to understand patient perspectives on physician behaviours during EOL communication.

Design
In this mixed methods study, we conducted quantitative and qualitative strands and then merged data sets during a mixed methods analysis phase. In the quantitative strand, we used the quality of communication tool (QOC) to measure physician behaviours that predict global rating of satisfaction in EOL communication skills, while in the qualitative strand we conducted semi-structured interviews. During the mixed methods analysis, we compared and contrasted qualitative and quantitative data.

Setting and Participants
Seriously ill inpatients at three tertiary care hospitals in Canada.

Results
We found convergence between qualitative and quantitative strands: patients desire candid information from their physician and a sense of familiarity. The quantitative results (n = 132) suggest a paucity of certain EOL communication behaviours in this seriously ill population with a limited prognosis. The qualitative findings (n = 16) suggest that at times, physicians did not engage in EOL communication despite patient readiness, while sometimes this may represent an appropriate deferral after assessment of a patient's lack of readiness.

Conclusions
Avoidance of certain EOL topics may not always be a failure if it is a result of an assessment of lack of patient readiness. This has implications for future tool development: a measure could be built in to assess whether physician behaviours align with patient readiness.