A comparison of stress intensity factors through crack closure integral and other approaches using eXtended element-free Galerkin method

In this paper, a new approach for extracting stress intensity factors (SIFs) by the extended element-free Galerkin method, through a crack closure integral (CCI) scheme, is proposed. The CCI calculation is used in conjunction with a local smoothing technique to improve the accuracy of the computed SIFs in a number of case studies of linear elastic fracture mechanics. The cases involve problems of mixed-mode, curved crack and thermo-mechanical loading. The SIFs by CCI, displacement and stress methods are compared with those based on the M-integral technique reported in the literature. The proposed CCI method involves very simple relations, and still gives good accuracy. The convergence of the results is also examined.

Element-Free Galerkin modelling of composite damage

Delamination and matrix cracking are routine damage mechanisms, observed by post-mortem analysis of laminated structures containing geometrical features such as notches or bolts. Current finite element tools cannot explicitly model an intralaminar matrix microcrack, except if the location of the damage is specified a priori. In this work, a meshless technique, the Element-Free Galerkin (EFG) method, is utilized for the first time to simulate delamination (interlaminar) and intralaminar matrix microcracking in composite laminates.

Element-Free Galerkin Modelling of Crack Migration in Composite Laminates

The development of a virtual testing environment, as a cost-effective industrial design tool in the design and analysis of composite structures, requires the need to create models efficiently, as well as accelerate the analysis by reducing the number of degrees of freedom, while still satisfying the need for accurately tracking the evolution of a debond, delamination or crack front. The eventual aim is to simulate both damage initiation and propagation in components with realistic geometrical features, where crack propagation paths are not trivial. Meshless approaches, and the Element-Free Galerkin (EFG) method, are particularly suitable for problems involving changes in topology and have been successfully applied to simulate damage in homogeneous materials and concrete. In this work, the method is utilized to model initiation and mixed-mode propagation of cracks in composite laminates, and to simulate experimentally-observed crack migration which is difficult to model using standard finite element analysis. N

Full-Wave Analysis of Layered Aperture Arrays

The new rigorous numerical-analytical technique based upon Galerkin method with the entire domain basis functions has been developed and applied to the study of the periodic aperture arrays containing multiple dissimilar apertures of complex shapes in stratified medium. The rapid uniform convergence of the solutions has enabled a comprehensive parametric study of complex array arrangements. The developed theory has revealed new effects of the aperture shape and layout on the array performance. The physical mechanisms underlying the TM wave resonances and Luebbers' anomaly have been explained for the first time.

A numerical investigation of the flow structures and losses for turbulent flow in 90 degrees elbow bends

Computational fluid dynamic modelling was carried out on a series of pipe bends having R/r values of 1.3, 5, and 20, with the purpose of determining the accuracy of numerical models in predicting pressure loss data from which to inform one-dimensional loss models. Four separate turbulence models were studied: the standard k-epsilon model, realizable k-epsilon model, k-omega model, and a Reynolds stress model (RSM). The results are presented for each bend in the form of upstream and downstream pressure profiles, pressure distributions along the inner and outer walls, detailed pressure and velocity fields as well as overall loss values. In each case, measured data were presented to evaluate the predictive ability of each model. The RSM was found to perform the best, producing accurate pressure loss data for bends with R/r values of 5 and 20. For the tightest bend with an R/r value of 1.3, however, predictions were significantly worse due to the presence of flow separation, stronger pressure gradients, and high streamline curvature.

A work-based research assessment of the impact of 'lean manufacturing' on health and safety education within an SME

Globalisation has had a major impact on the engineering industry as pacific Rim countries undercut manufacturing costs and provide a more cost-effective location for many businesses. Engineering in Nortehrn Ireland has mostly declined owing to increased competition from these countries. Engineering companies are now forced to streamline their production processes and employ cost-reducing practices in order to meet customer demands at reduced prices. This article aims to analyse the effects of one such streamlining endeavour which was first introduced after World War II in Japan- 'lean manufacturing' . 'Lean manufacturing' aims to reduce all wasteful activities within the production process in order to improve productivity, while reducing manufacturing costs. The work-based project under consideration was concerned with the impact 'lean manufacturing' may have on health and safety performance and education within an engineering company. The focus of the project was to determine through work-based research, and quantitative analysis, the employee perception on health and safety: has it changed (either positively or negatively), as a consequence of implementing 'lean manufacturing'.

Calculation of loss in conductors of a superconducting shielded slotted line and a coplanar waveguide

Finite conductivity in superconductors is taken into account by approximate boundary conditions imposed directly when deriving pair summatory equations, which are solved using the Galerkin method and the basis describing the edge singularity.

Implementation of Menter's Transition Model on an Isolated Natural Laminar Flow Nacelle

This study evaluates the implementation of Menter's gamma-Re-theta Transition Model within the CFX12 solver for turbulent transition prediction on a natural laminar flow nacelle. Some challenges associated with this type of modeling have been identified. The computational fluid dynamics transitional flow simulation results are presented for a series of cruise cases with freestream Mach numbers ranging from 0.8 to 0.88, angles of attack from 2 to 0 degrees, and mass flow ratios from 0.60 to 0.75. These were validated with a series of wind-tunnel tests on the nacelle by comparing the predicted and experimental surface pressure distributions and transition locations. A selection of the validation cases are presented in this paper. In all cases, computational fluid dynamics simulations agreed reasonably well with the experiments. The results indicate that Menter's gamma-Re-theta Transition Model is capable of predicting laminar boundary-layer transition to turbulence on a nacelle. Nonetheless, some limitations exist in both the Menter's gamma-Re-theta Transition Model and in the implementation of the computational fluid dynamics model. The implementation of a more comprehensive experimental correlation in Menter's gamma-Re-theta Transition Model, preferably the ones from nacelle experiments, including the effects of compressibility and streamline curvature, is necessary for an accurate transitional flow simulation on a nacelle. In addition, improvements to the computational fluid dynamics model are also suggested, including the consideration of varying distributed surface roughness and an appropriate empirical correction derived from nacelle experimental transition location data.

Computation of stress intensity factors in functionally graded materials using partition-of-unity meshfee method

This paper describes the computation of stress intensity factors (SIFs) for cracks in functionally graded materials (FGMs) using an extended element-free Galerkin (XEFG) method. The SIFs are extracted through the crack closure integral (CCI) with a local smoothing technique, non-equilibrium and incompatibility formulations of the interaction integral and the displacement method. The results for mode I and mixed mode case studies are presented and compared with those available in the literature. They are found to be in good agreement where the average absolute error for the CCI with local smoothing, despite its simplicity, yielded a high level of accuracy.

Modified crack closure integral technique for extraction of SIFs in meshfee methods

A new approach for extracting stress intensity factors (SIFs) by the element-free Galerkin (EFG) class of methods through a modified crack closure integral (MCCI) scheme is proposed. Its primary feature is that it allows accurate calculation of mode I and mode II SIFs with a relatively simple and straightforward analysis even when a coarser nodal density is employed. The details of the adoption of the MCCI technique in the EFG method are described. Its performance is demonstrated through a number of case studies including mixed-mode and thermal problems in linear elastic fracture mechanics (LEFM). The results are compared with published theoretical solutions and those based on the displacement method, stress method, crack closure integral in conjunction with local smoothing (CCI–LS) technique, as well as the M-integral method. Its advantages are discussed.

Application of halohydrocarbons for the re-dispersion of gold particles

Methods to control the dispersion of gold in supported heterogeneous catalysts are very valuable due to the strong nanoparticle size dependence on their activity and selectivity towards many reactions. Additionally, the ability to disperse large, inactive gold nanoparticles to smaller nanoparticles provides an opportunity to reactivate, stabilise and increase the lifetime of gold catalysts making them more practical for industrial applications. Previously it has been demonstrated that the use of gas phase iodomethane (J. Am. Chem. Soc., 2009, 131, 6973; Angew. Chem., Int. Ed., 2011, 50, 8912) was able to re-disperse gold from >20 nm particles to dimers and trimers. In the current work, we show that this technique can be applied using less hazardous halohydrocarbons treatments, both in the gas phase and the liquid phase. The ability of these individual halohydrocarbons to re-disperse gold as well as the extent to which leaching occurs is assessed.