Fracture Mechanics Analysis of the Dentine-Luting Cement Interface.

The objectives of this study were to determine the fracture toughness of adhesive interfaces between dentine and clinically relevant, thin layers of dental luting cements. Cements tested included a conventional glass-ionomer, F (Fuji I), a resin-modified glass-ionomer, FP (Fuji Plus) and a compomer cement, D (DyractCem). Ten miniature short-bar chevron notch specimens were manufactured for each cement, each comprising a 40 µm thick chevron of lute, between two 1.5 mm thick blocks of bovine dentine, encased in resin composite. The interfacial KIC results (MN/m3/2) were median (range): F; 0.152 (0.14-0.16), FP; 0.306 (0.27-0.37), D; 0.351 (0.31-0.37). Non-parametric statistical analysis showed that the fracture toughness of F was significantly lower (p

Quantification of all-ceramic crown margin surface profile from try-in to 1-week post-cementation

To use profilometry to assess the margin surface profile of all-ceramic crowns (ACC’s) at try-in and 1-week after cementation with dual-cured resin (DC, RelyX ARC, 3 M ESPE, St. Paul, MN, USA), self-adhesive dual-cured resin (SADC, RelyX Unicem, 3 M ESPE), light-cured resin (LC, RelyX Veneer, 3 M ESPE) or chemically cured resin-modified glass ionomer (RMGI, RelyX Luting Plus, 3 M ESPE) luting cement. Methods: Forty, sound, extracted, human, premolar teeth underwent a standardised preparation for ACC’s. IPS Empress (Ivoclar-Vivadent, Liechtenstein) crowns of standard dimensions were fabricated and 10 luted with each cement and stored in water for 7 days. Three groups of serial profiles were taken, the first of the tooth preparation, the second of the crown margins at try-in and lastly of the crown margins after cementation and 7 days water storage. Results: There were no significant differences in the crown margin surface profile between the four cement groups at try-in. The change in crown margin position between try-in and post-cementation was significantly greater for DC than for LC and RMGI. SADC was not significantly different to the other cements. There were no significant differences in the crown margin extensions between the four cement groups, however most of the IPS Empress ACC’s in this study were underextended but this was not statistically significant. Conclusions: IPS Empress ACC’s seated more fully with LC and RMGI than with DC cement

Two-year survival of ART restorations placed in elderly patients: A randomised controlled clinical trial

OBJECTIVES: Older dentate adults are a high caries risk group who could potentially benefit from the use of the atraumatic restorative treatment (ART). This study aimed to compare the survival of ART and a conventional restorative technique (CT) using rotary instruments and a resin-modified glass-ionomer for restoring carious lesions as part of a preventive and restorative programme for older adults after 2 years.

METHODS: In this randomised controlled clinical trial, 99 independently living adults (65-90 years) with carious lesions were randomly allocated to receive either ART or conventional restorations. The survival of restorations was assessed by an independent and blinded examiner 6 months, 1 year and 2 years after restoration placement.

RESULTS: Ninety-six (67.6%) and 121 (76.6%) restorations were assessed in the ART and CT groups, respectively, after 2 years. The cumulative restoration survival percentages after 2 years were 85.4% in the ART and 90.9% in the CT group. No statistically significant between group differences were detected (p=0.2050, logistic regression analysis).

CONCLUSIONS: In terms of restoration survival, ART was as effective as a conventional restorative approach to treat older adults after 2 years. This technique could be a useful tool to provide dental care for older adults particularly in the non-clinical setting. (Trial Registration number: ISRCTN 76299321).

CLINICAL SIGNIFICANCE: The results of this study show that ART presented survival rates similar to conventional restorations in older adults. ART appears to be a cost-effective way to provide dental care to elderly patients, particularly in out of surgery facilities, such as nursing homes.

The Use of ART in Elderly Patients after 2 years

Caries experience is high in the elderly, and barriers to care for older adults include fear and cost. Access to care is especially problematic in the case of frail and homebound elderly. Objective: to compare the survival of restorations placed using Atraumatic Restorative Treatment (ART) and a conventional technique using rotary instruments and a resin-modified glass-ionomer (CT) to treat carious lesions in older patients. Methods: In this randomised clinical trial, 99 independently living adults (65-90 yrs) with carious lesions were recruited from a geriatric day hospital and a community centre and randomly allocated to receive either ART or conventional restorations. They received tailored oral hygiene instructions and scaling and polishing of teeth prior to restoration placement. The survival of restorations was assessed 6, 12 and 24 months after restoration placement by an independent examiner. Results: Ninety-nine patients participated in the trial, 46 males and 53 females, with a mean age of 73.2 (SD: 6.8). In total, 300 restorations were placed, 142 ART in 51 patients and 158 conventional restorations in 48 patients, with an average of 2.8 ART (SD: 1.83) and 3.2 conventional (SD: 2.62) restorations placed per patient. After 2 years, 88 ART and 117 conventional restorations were assessed. The restoration survival percentages were 93.1% and 94%, respectively. Conclusion: ART was found to be as effective as a conventional restorative approach to treat older adults after 2 years and could be a useful tool to provide dental care for older dentate adults.

Carbon nanotube modified carbon composite monoliths as superior adsorbents for carbon dioxide capture

Carbon composite monoliths were prepared from a commercial phenolic resin mixed with just 1 wt% of carbon nanotubes (CNTs) followed by carbonization and physical activation with CO. The products possess a hierarchical macroporous-microporous structure and superior CO adsorption properties. In particular, they show the top-ranked CO capacity (52 mg CO per g adsorbent at 25 °C and 114 mmHg) under low CO partial pressures, which is of more relevance for flue gas applications. This matches or exceeds those of carbons produced by complex chemical activation and functionalization. Our study demonstrates an effective way to create narrow micropores through structural modification of carbon composites by CNTs. © 2013 The Royal Society of Chemistry.

Multilayered glass fibre-reinforced composites in rotational moulding

The potential of multiple layer fibre-reinforced mouldings is of growing interest to the rotational moulding industry because of their cost/performance ratio. The particular problem that arises when using reinforcements in this process relate to the fact that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this study, short glass fibres were incorporated and distributed into a polymer matrix to produce fibre-reinforced polymer composites using the rotational moulding process and characterised in terms of morphology and mechanical properties. © 2011 American Institute of Physics.

Glass fibre-reinforced polyethylene composites in rotational moulding

Fibre-reinforced mouldings are of growing interest to the rotational moulding industry due to their outstanding price performance ratio. However, a particular problem that arises when using reinforcements in this process is that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this paper we report on studies to incorporate, short glass fibres into rotationally moulded parts. Four different approaches were investigated; direct addition of fibre in between two powder shots, addition of a layer of pre-compounded polyethylene-glass fibre pellets between two powder shots, addition of a layer of pre-compounded polyethylene-glass fibre powder between two powder shots and a single layer of glass-reinforced, pre-compounded powder. Results indicate that pre-compounding is necessary to gain performance enhancement and the single layer part made from glass-reinforced, pre-compounded powder exhibited the highest tensile and flexural modulus.