Single sideband FSS with high image rejection

The design of a quasi-optical single sideband filter, which provides more than 30 dB of isolation between the frequency bands 294-305.5 and 329.5-341.5 GHz in the TM plane at 45 degrees incidence, is described. The structure, which consists of three free-standing arrays of dipole slot elements, generates a bandpass spectral response with an insertion loss below 0.5 dB at resonance. Simulated and measured transmission coefficients in the range 250-400 GHz are shown to be in good agreement.

Multivariate prediction of clarified butter composition using Raman spectroscopy

Raman spectroscopy has been used to predict the abundance of the FA in clarified butterfat that was obtained from dairy cows fed a range of levels of rapeseed oil in their diet. Partial least squares regression of the Raman spectra against FA compositions obtained by GC showed good prediction for the five major (abundance >5%) FA with R-2=0.74-0.92 and a root mean SE of prediction (RMSEP) that was 5-7% of the mean. In general, the prediction accuracy fell with decreasing abundance in the sample, but the RMSEP was 1.25%. The Raman method has the best prediction ability for unsaturated FA (R-2=0.85-0.92), and in particular trans unsaturated FA (best-predicted FA was 18:1 tDelta9). This enhancement was attributed to the isolation of the unsaturated modes from the saturated modes and the significantly higher spectral response of unsaturated bonds compared with saturated bonds. Raman spectra of the melted butter samples could also be used to predict bulk parameters calculated from standard analyzes, such as iodine value (R-2=0.80) and solid fat content at low temperature (R-2=0.87). For solid fat contents determined at higher temperatures, the prediction ability was significantly reduced (R-2=0.42), and this decrease in performance was attributed to the smaller range of values in solid fat content at the higher temperatures. Finally, although the prediction errors for the abundances of each of the FA in a given sample are much larger with Raman than with full GC analysis, the accuracy is acceptably high for quality control applications. This, combined with the fact that Raman spectra can be obtained with no sample preparation and with 60-s data collection times, means that high-throughput, on-line Raman analysis of butter samples should be possible.

Submillimeter wave frequency selective surface with polarisation independent spectral responses

This paper reports the design, construction and electromagnetic performance of a new freestanding frequency selective surface (FSS) structure which generates coincident spectral responses for dual polarisation excitation at oblique angles of incidence. The FSS is required to allow transmission of 316.5 - 325.5 GHz radiation with a loss = 0.6 dB and to achieve = 30 dB rejection from 349.5 - 358.5 GHz. It should also exhibit crosspolarisation levels below -25 dB, all criteria being satisfied simultaneously for TE and TM polarisations at 45° incidence. The filter consists of two identical, 30 mm diameter, 12.5 ?m thick, optically flat, perforated metal screens separated by 450 ?m. Each of the ˜5000 unit cells contains two nested, short circuited, rectangular loop slots and a rectangular dipole slot. The nested elements provide a passband spectral response centred at 320 GHz in the TE and TM planes; the dipole slot increases the filter roll-off above resonance. The FSS was fabricated from silicon-on-insulator wafers using precision micromachining and plating processes including the use of Deep Reactive Ion Etching (DRIE) to pattern the individual slots and remove the substrate under the periodic arrays. Quasi–optical transmission measurements in the 250 – 360 GHz range yielded virtually identical copolarised spectral responses, with the performance meeting or exceeding the above specifications. Experimental results are in excellent agreement with numerical predictions.

The effect of the spectral distribution of wave energy on the performance of a bottom hinged flap type wave energy converter

The power output from a wave energy converter is typically predicted using experimental and/or numerical modelling techniques. In order to yield meaningful results the relevant characteristics of the device, together with those of the wave climate must be modelled with sufficient accuracy.

The wave climate is commonly described using a scatter table of sea states defined according to parameters related to wave height and period. These sea states are traditionally modelled with the spectral distribution of energy defined according to some empirical formulation. Since the response of most wave energy converters vary at different frequencies of excitation, their performance in a particular sea state may be expected to depend on the choice of spectral shape employed rather than simply the spectral parameters. Estimates of energy production may therefore be affected if the spectral distribution of wave energy at the deployment site is not well modelled. Furthermore, validation of the model may be affected by differences between the observed full scale spectral energy distribution and the spectrum used to model it.

This paper investigates the sensitivity of the performance of a bottom hinged flap type wave energy converter to the spectral energy distribution of the incident waves. This is investigated experimentally using a 1:20 scale model of Aquamarine Power’s Oyster wave energy converter, a bottom hinged flap type device situated at the European Marine Energy Centre (EMEC) in approximately 13m water depth. The performance of the model is tested in sea states defined according to the same wave height and period parameters but adhering to different spectral energy distributions.

The results of these tests show that power capture is reduced with increasing spectral bandwidth. This result is explored with consideration of the spectral response of the device in irregular wave conditions. The implications of this result are discussed in the context of validation of the model against particular prototype data sets and estimation of annual energy production.

Micromachined 300GHz high Q resonant slot frequency selective surface filter

The design of a low loss quasi-optical beam splitter which is required to provide efficient diplexing of the bands 316.5-325.5 GHz and 349.5-358.5 GHz is presented. To minimise the filter insertion loss, the chosen architecture is a three-layer freestanding array of dipole slot elements. Floquet modal analysis and finite element method computer models are used to establish the geometry of the periodic structure and to predict its spectral response. Two different micromachining approaches have been employed to fabricate close packed arrays of 460 mm long elements in the screens that form the basic building block of the 30mm diameter multilayer frequency selective surface. Comparisons between simulated and measured transmission coefficients for the individual dichroic surfaces are used to determine the accuracy of the computer models and to confirm the suitability of the fabrication methods.

What role for DNA damage and repair in the bystander response?

The radiation-induced bystander effect challenges the accepted paradigm of direct DNA damage in response to energy deposition driving the biological consequences of radiation exposure. With the bystander response, cells which have not been directly exposed to radiation respond to their neighbours being targeted. In our own studies we have used novel targeted microbeam approaches to specifically irradiate parts of individual cells within a population to quantify the bystander response and obtain mechanistic information. Using this approach it has become clear that energy deposited by radiation in nuclear DNA is not required to trigger the effect, with cytoplasmic irradiation required. Irradiated cells also trigger a bystander response regardless of whether they themselves live or die, suggesting that the phenotype of the targeted cell is not a determining factor. Despite this however, a range of evidence has shown that repair status is important for dealing with the consequences of a bystander signal. Importantly, repair processes involved in the processing of dsb appear to be involved suggesting that the bystander response involves the delayed or indirect production of dsb-type lesions in bystander cells. Whether these are infact true dsb or complexes of oxidised bases in combination with strand breaks and the mechanisms for their formation, remains to be elucidated.

BRCA1 and implications for response to chemotherapy in ovarian cancer

Objectives: Treatment of epithelial ovarian cancer (EOC) remains a challenge, despite advances in surgery and chemotherapy. Hereditary ovarian cancer is primarily due to germline mutations in the BRCA1 tumour suppressor gene. In addition, sporadic EOC tumours display signi?cant of loss of BRCA1 function due to epigenetic inactivation of the BRCA1 gene. This article reviews the preclinical and clinical evidence to support a role for BRCA1 as a potential predictive biomarker of response to both platinum and taxane based chemotherapy in EOC.

Methods: We conducted a Medline and Pubmed search for reports between 1990 and 2008 using the search terms: BRCA1 and hereditary ovarian cancer, BRCA1 and sporadic ovarian cancer, ovarian cancer and chemotherapy, ovarian cancer and taxanes, ovarian cancer and platinums, ovarian cancer and clinical response, BRCA1 and DNA damage, BRCA1 and DNA repair, BRCA1 and mitotic checkpoint. If reports identi?ed by these criteria referred to other papers not in the initial search, then these were also reviewed if relevant to BRCA1 and ovarian cancer.

Results: The BRCA1 pathway plays a signi?cant role in the development of both hereditary and sporadic EOC. Evidence suggests that BRCA1 is a potential biomarker of response to platinum chemotherapy in EOC with BRCA1 de?ciency predicting for enhanced response. In contrast, initial evidence suggests that loss of BRCA1 function results in reduced response to antimicrotubule-based chemotherapy. The ability of BRCA1 to differentially modulate response to these agents involves loss of BRCA1 mediated DNA repair and mitotic checkpoint control, respectively.

Conclusions: Standard ?rst line treatment of EOC consists of a combination of platinum and taxane chemotherapy, however clinically useful biomarkers for predicting response to these agents have yet to be established. BRCA1 may prove useful as a biomarker in EOC for assigning chemotherapy treatments based on the presence or absence of BRCA1 function.

Ultrafast nonlinearities of minibands in metallodielectric Bragg resonators

The nonlinear properties of metallodielectric DBRs are investigated via optical pump-probe techniques using a widely tunable, dual-colour, high-repetition rate, ultrafast setup. As a consequence of the Bragg-arranged multilayers, the electric field penetrates to different depths of the nanostructure at different excitation resonances, strongly enhancing the intrinsic nonlinear response of the metal in comparison with bulk films. The analyzed spectral response of these structures reveals how their nonlinear behavior is dominated by the pump-induced modification of the metal dielectric function. Fitting the simulated changes of the optical resonances using transfer-matrix methods matches experiment well, and shows the key effects of the spectral dependence of the spatial mode profiles.

Haptoglobin Phenotype, Preeclampsia and Response to Supplementation with Vitamins C and E in Pregnant Women with Type 1 Diabetes.

Objective The phenotype of the antioxidant and pro-angiogenicprotein haptoglobin (Hp) predicts cardiovascular disease risk andtreatment response to antioxidant vitamins in individuals withdiabetes. Our objective was to determine whether Hp phenotypeinfluences pre-eclampsia risk, or the efficacy of vitamins C and Ein preventing pre-eclampsia, in women with type-1 diabetes.
Design This is a secondary analysis of a randomised controlledtrial in which women with diabetes received daily vitamins C andE, or placebo, from 8 to 22 weeks of gestation until delivery.
Setting Twenty-five antenatal metabolic clinics across the UK (innorth-west England, Scotland, and Northern Ireland).
Population Pregnant women with type-1 diabetes.
Methods Hp phenotype was determined in white women whocompleted the study and had plasma samples available (n = 685).
Main outcome measure Pre-eclampsia.
Results Compared with Hp 2-1, Hp 1-1 (OR 0.59, 95% CI 0.30–1.16) and Hp 2-2 (OR 0.93, 95% CI 0.60–1.45) were notassociated with significantly decreased pre-eclampsia risk afteradjusting for treatment group and HbA1c at randomisation. Ourstudy was not powered to detect an interaction between Hpphenotype and treatment response; however, our preliminaryanalysis sugge sts that vitamins C and E did not prevent pre-eclampsia in women of any Hp phenotype (Hp 1-1, OR 0.77, 95%CI 0.22–2.71; Hp 2-1, OR 0.81, 95% CI 0.46–1.43; Hp 2-2, 0.67,95% CI 0.34–1.33), after adjusting for HbA1c at randomisation.
Conclusions The Hp phenotype did not significantly affect pre-eclampsia risk in women with type-1 diabetes.

Electrical characterisation of liquid crystals at millimetre wavelengths using frequency selective surfaces

Email
Print











The accurate measurement of the permittivity, loss tangent and dielectric anisotropy DC bias dependence for two different liquid crystal (LC) materials in the frequency range 140-165 GHz is described. The electrical characteristics are obtained by curve fitting computed transmission coefficients to the experimental spectral response of a new class of electronically reconfigurable frequency selective surface. The periodic structure is designed to yield bandpass filter characteristics with and without an applied bias control voltage in order to measure the tunability of the LC material which is inserted in a 705 µm-thick cavity.

Comportamento flessionale di nodi esterni in calcestruzzo fibrorinforzato

SOMMARIO – Si presenta un macro modello di tipo reticolare in grado di riprodurre il comportamento in presenza di taglio e momento di nodi esterni trave-colonna di telai in calcestruzzo fibrorinforzato con fibre di acciaio
uncinato ed ordinario. Il caricamento del sistema è di tipo monotono come nel caso dell’analisi di pushover. Il modello considera la presenza di armature orizzontali e verticali della regione nodale e tiene in conto delle modalità
di rottura legate allo snervamento delle barre e allo schiacciamento delle regioni compresse in regime di sforzi pluriassiali. Il modello include le deformazioni flessionali della trave e della colonna in presenza di sforzo normale costante e restituisce la risposta del sistema colonna-nodo-trave (sub-assembralggio) tramite le curve carico-freccia all’estremità della semitrave. Per i singoli costituenti (trave, colonna e nodo) si è considerata la prima fessurazione, lo snervamento e lo schiacciamento delle regioni compresse e si sono fornite precise indicazioni sulla sequenza degli eventi che come è noto sono di fondamentale importanza per lo sviluppo di un progetto plastico che rispetti la gerarchia delle resistenze. Con l’uso del modello il controllo della gerarchia delle resistenze avviene a livello sezionale (lo snervamento delle barre deve avvenire prima dello schiacciamento delle regioni compresse) o di macro elemento (nella regione nodale lo snervamento delle staffe precede la crisi dei puntoni) e dell’intero elemento
sub-assemblaggio trave debole, colonna forte e nodo sovraresistente.
La risposta ottenuta con i modello proposto è in buon accordo con le risposte sperimentali disponibili in letteratura (almeno in termini di resistenza del sub-assemblaggio). Il modello è stato ulteriormente validato con analisi
numeriche agli elementi finiti condotte con il codice ATENA-2D. Le analisi numeriche sono state condotte utilizzando per il calcestruzzo fibroso adeguate leggi costitutive proposte dagli autori ed in grado di cogliere gli effetti
di softening e di resistenza residua a trazione legati alla presenza di fibre. Ulteriori sviluppi del modello saranno indirizzati a includere gli effetti di sfilamento delle barre d’armatura della trave e del conseguente degrado delle
tensioni d’aderenza per effetto di carichi monotonici e ciclici.

SUMMARY – A softened strut-and-tie macro model able to reproduce the flexural behavior of external beam-tocolumn joints with the presence of horizontal and vertical steel bars, including softening of compressed struts and yielding of main and secondary steel bars, is presented, to be used for the pushover analysis. The model proposed is able to calculate also the flexural response of fibrous reinforced concrete (FRC) beam-to-column sub-assemblages in term of a multilinear load-deflection curves. The model is able to take into account of the tensile behavior of main bars embedded in the surrounding concrete and of the softening of the compressed strut, the arrangement and percentage of the steel bars, the percentage and the geometry of steel fibers. First cracking, yielding of main steel and crushing of concrete were identified to determine the corresponding loads and displacement and to plot the simplified monotonic load-deflection curves of the sub-assemblages subjected in the column to constant vertical
load and at the tip of the beam to monotonically increasing lateral force. Through these load-delfection curves the component (beam, joint and column) that first collapse can be recognized and the capacity design can be verified.
The experimental results available in the literature are compared with the results obtained through the proposed model. Further, a validation of the proposed model is numerically made by using a non linear finite element program (ATENA-2D) able to analyze the flexural behavior of sub-assemblages.