Factorial Design of Cement Slurries Containing Limestone Powder for Self-Consolidating Slurry-Infiltrated Fiber Concrete

Slurries with high penetrability for production of Self-consolidating Slurry Infiltrated Fiber Concrete (SIFCON) were investigated in this study. Factorial experimental design was adopted in this investigation to assess the combined effects of five independent variables on mini-slump test, plate cohesion meter, induced bleeding test, J-fiber penetration test and compressive strength at 7 and 28 days. The independent variables investigated were the proportions of limestone powder (LSP) and sand, the dosages of superplasticiser (SP) and viscosity agent (VA), and water-to-binder ratio (w/b). A two-level fractional factorial statistical method was used to model the influence of key parameters on properties affecting the behaviour of fresh cement slurry and compressive strength. The models are valid for mixes with 10 to 50% LSP as replacement of cement, 0.02 to 0.06% VA by mass of cement, 0.6 to 1.2% SP and 50 to 150% sand (% mass of binder) and 0.42 to 0.48 w/b. The influences of LSP, SP, VA, sand and W/B were characterised and analysed using polynomial regression which identifies the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, J-fiber penetration test, induced bleeding and compressive strength as functions of LSP, SP, VA, sand and w/b. The estimated results of mini-slump, induced bleeding test and compressive strength from the derived models are compared with results obtained from previously proposed models that were developed for cement paste. The proposed response models of the self-consolidating SIFCON offer useful information regarding the mix optimization to secure a highly penetration of slurry with low compressive strength

Influence of mix proprtions on rheolgy of cement grouts containing limestone powder

In this paper the parameters of cement grout affecting rheological behaviour and compressive strength are investigated. Factorial experimental design was adopted in this investigation to assess the combined effects of the following factors on fluidity, rheological properties, induced bleeding and compressive strength: water/binder ratio (W/B), dosage of superplasticiser (SP), dosage of viscosity agent (VA), and proportion of limestone powder as replacement of cement (LSP). Mini-slump test, Marsh cone, Lombardi plate cohesion meter, induced bleeding test, coaxial rotating cylinder viscometer were used to evaluate the rheology of the cement grout and the compressive strengths at 7 and 28 days were measured. A two-level fractional factorial statistical model was used to model the influence of key parameters on properties affecting the fluidity, the rheology and compressive strength. The models are valid for mixes with 0.35-0.42 W/B, 0.3-1.2% SP, 0.02-0.7% VA (percentage of binder) and 12-45% LSP as replacement of cement. The influences of W/B, SP, VA and LSP were characterised and analysed using polynomial regression which can identify the primary factors and their interactions on the measured properties. Mathematical polynomials were developed for mini-slump, plate cohesion meter, inducing bleeding, yield value, plastic viscosity and compressive strength as function of W/B, SP, VA and proportion of LSP. The statistical approach used highlighted the limestone powder effect and the dosage of SP and VA on the various rheological characteristics of cement grout

Evolutionary agglomeration theory: increasing returns, diminishing returns, and the industry life cycle

According to Marshall’s agglomeration theory, Krugman’s New Economic Geography models, and Porter’s cluster policies, firms should receive increasing returns from a trinity of agglomeration economies: a local pool of skilled labour, local supplier linkages, and local knowledge spillovers. Recent evolutionary theories suggest that whether agglomeration economies generate increasing returns or diminishing returns depends on time, and especially the evolution of the industry life cycle. At the start of the twenty-first century, we re-examine Marshall’s trinity of agglomeration economies in the city-region where he discovered them. The econometric results from our multivariate regression models are the polar opposite of Marshall’s. During the later stages of the industry life cycle, Marshall’s agglomeration economies decrease the economic performance of firms and create widespread diminishing returns for the economic development of the city-region, which has evolved to become one of the poorest city-regions in Europe.

rbcL sequences indicate a single evolutionary origin of multinucleate cells in the red algal tribe Callithamnieae.

In the Ceramiaceae, one of the largest families of the red algae, there are from 1 to 4000 nuclei in each vegetative cell, but each tribe is homogeneous with respect to the uninucleate/multinucleate character state, except for the Callithamnieae. The goals of this study were to analyze rbcL gene sequences to clarify the evolution of taxa within the tribe Callithamnieae and to evaluate the potential evolutionary significance of the development of multinucleate cells in certain taxa. The genus Aglaothamnion, segregated from Callithamnion because it is uninucleate, was paraphyletic in all analyses. Callithamnion (including Aristothamnion) was monophyletic although not robustly so, apparently due to variations between taxa in rate of sequence evolution. Morphological synapomorphies were identified at different depths in the tree, supporting the molecular phylogenetic analysis. The uninucleate character state is ancestral in this tribe. The evolution of multinucleate cells has occurred once in the Callithamnieae. Multiple nuclei in each cell may combine the benefits of small C values (rapid cell cycle) with large cells (permitting morphological elaboration) while maintaining a constant ratio of nuclear volume: cytoplasmic volume.

Relationship between biomedical catheter surface properties and lubricity as determined using textural analysis and multiple regression analysis

In this study, the surface properties of and work required to remove 12 commercially available and developmental catheters from a model biological medium (agar), a measure of catheter lubricity, were characterised and the relationships between these properties were examined using multiple regression and correlation analysis. The work required for removal of catheter sections (7 cm) from a model biological medium (1% w/w agar) were examined using tensile analysis. The water wettability of the catheters were characterised using dynamic contact angle analysis, whereas surface roughness was determined using atomic force microscopy. Significant differences in the ease of removal were observed between the various catheters, with the silicone-based materials generally exhibiting the greatest ease of removal. Similarly, the catheters exhibited a range of advancing and receding contact angles that were dependent on the chemical nature of each catheter. Finally, whilst the microrugosities of the various catheters differed, no specific relationship to the chemical nature of the biomaterial was apparent. Using multiple regression analysis, the relationship between ease of removal, receding contact angle and surface roughness was defined as: Work done (N mm) 17.18 + 0.055 Rugosity (nm)-0.52 Receding contact angle (degrees) (r = 0.49). Interestingly, whilst the relationship between ease of removal and surface roughness was significant (r = 0.48, p = 0.0005), in which catheter lubricity increased as the surface roughness decreased, this was not the case with the relationship between ease of removal and receding contact angle (r = -0.18, p > 0.05). This study has therefore uniquely defined the contributions of each of these surface properties to catheter lubricity. Accordingly, in the design of urethral catheters. it is recommended that due consideration should be directed towards biomaterial surface roughness to ensure maximal ease of catheter removal. Furthermore, using the method described in this study, differences in the lubricity of the various catheters were observed that may be apparent in their clinical use. (C) 2003 Elsevier Ltd. All rights reserved.

Software Release Planning: An Evolutionary and Iterative Approach

Abstract To achieve higher flexibility and to better satisfy actual customer requirements, there is an increasing tendency to develop and deliver software in an incremental fashion. In adopting this process, requirements are delivered in releases and so a decision has to be made on which requirements should be delivered in which release. Three main considerations that need to be taken account of are the technical precedences inherent in the requirements, the typically conflicting priorities as determined by the representative stakeholders, as well as the balance between required and available effort. The technical precedence constraints relate to situations where one requirement cannot be implemented until another is completed or where one requirement is implemented in the same increment as another one. Stakeholder preferences may be based on the perceived value or urgency of delivered requirements to the different stakeholders involved. The technical priorities and individual stakeholder priorities may be in conflict and difficult to reconcile. This paper provides (i) a method for optimally allocating requirements to increments; (ii) a means of assessing and optimizing the degree to which the ordering conflicts with stakeholder priorities within technical precedence constraints; (iii) a means of balancing required and available resources for all increments; and (iv) an overall method called EVOLVE aimed at the continuous planning of incremental software development. The optimization method used is iterative and essentially based on a genetic algorithm. A set of the most promising candidate solutions is generated to support the final decision. The paper evaluates the proposed approach using a sample project.

B-type supergiants in the Small Magellanic Cloud: rotational velocities and implications for evolutionary models

High-resolution spectra for 24 SMC and Galactic B-type supergiants have been analysed to estimate the contributions of both macroturbulence and rotation to the broadening of their metal lines. Two different methodologies are considered, viz. goodness-of-fit comparisons between observed and theoretical line profiles and identifying zeros in the Fourier transforms of the observed profiles. The advantages and limitations of the two methods are briefly discussed with the latter techniques being adopted for estimating projected rotational velocities ( v sin i) but the former being used to estimate macroturbulent velocities. The projected rotational velocity estimates range from approximately 20 to 60 kms(-1), apart from one SMC supergiant, Sk 191, with a v sin i similar or equal to 90 km s(-1). Apart from Sk 191, the distribution of projected rotational velocities as a function of spectral type are similar in both our Galactic and SMC samples with larger values being found at earlier spectral types. There is marginal evidence for the projected rotational velocities in the SMC being higher than those in the Galactic targets but any differences are only of the order of 5 - 10 km s(-1), whilst evolutionary models predict differences in this effective temperature range of typically 20 to 70 km s(-1). The combined sample is consistent with a linear variation of projected rotational velocity with effective temperature, which would imply rotational velocities for supergiants of 70 kms(-1) at an effective temperature of 28 000 K ( approximately B0 spectral type) decreasing to 32 km s(-1) at 12 000 K (B8 spectral type). For all targets, the macroturbulent broadening would appear to be consistent with a Gaussian distribution ( although other distributions cannot be discounted) with an 1/e half-width varying from approximately 20 km s(-1) at B8 to 60 km s(-1) at B0 spectral types.