Bimetallic effects in the liquid phase hydrogenation of 2-butanone

A series of bimetallic Ru-containing monometallic and bimetallic catalysts were prepared and tested for their activity for the hydrogenation of 2-butanone to 2-butanol at 30 °C and 3 bar H2. RuPt bimetallic catalysts were the most active for the reaction, with a ratio of 5 wt% Ru:1 wt% Pt on activated carbon (AC) found to be optimum. The activity of this bimetallic catalyst was more than double that of the sum of the activities of the monometallic Ru and Pt catalysts, providing evidence of a “bimetallic” effect. Structural analysis of the bimetallic catalysts revealed that they consisted of clusters of particles of the order of 1–2 nm. Extended X-ray absorption fine structure analysis showed that there were two types of particle on the surface of the bimetallic RuPt catalyst, specifically monometallic Ru and bimetallic RuPt particles. For the bimetallic particles, it was possible to fit the data with a model in which a Ru core of 1.1 nm is enclosed by two Pt-rich layers, the outer layer containing only 13 at% Ru. Pretreatment of the monometallic and bimetallic catalysts in hydrogen had a significant effect on the activity. Both the bimetallic and monometallic Ru-based catalysts showed a trend of decreasing activity with increasing temperature of prereduction in hydrogen. This loss of activity was almost fully reversible by exposure of the catalysts to air after reduction. The changing activity with exposure to different gas phase environments could not be attributed to changes in particle size or surface composition. It is proposed that the introduction of hydrogen results in a gradual smoothing of the surface and loss of defect sites; this process being reversible on introduction of air. These defect sites are particularly important for the dissociative adsorption of hydrogen, potentially the rate-determining step in this reaction.

Catalytic hydrogenation of tertiary amides at low temperatures and pressures using bimetallic Pt/Re-based catalysts

Hydrogenation of tertiary amides, in particular, N-methylpyrrolidin-2-one, can be efficiently facilitated by a TiO(2)-supported bimetallic Pt/Re catalyst at low temperatures and pressures. Characterisation of the catalysts and kinetic tests have shown that the close interaction between the Re and Pt is crucial to the high activity observed. DFT calculations were used to examine a range of metal combinations and show that the role of the uncoordinated Re is to activate the C=O and that of the Pt is as a hydrogenation catalyst, removing intermediates from the catalyst surface. The rate enhancement observed on the TiO(2) support is thought to be due to the presence of oxygen vacancies allowing adsorption and weakening of the C=O bond. (C) 2011 Elsevier Inc. All rights reserved.

Structure-reactivity Correlations in the catalytic coupling of ethyne over novel bimetallic Pd/Sn catalysts

The structure, thermal stability, and catalytic behavior of a novel highly dispersed silica-supported Pd/Sn catalyst prepared by an organometallic route have been examined by X-ray photoelectron, X-ray diffraction, and X-ray absorption, fine structure spectroscopies, the latter two measurements being carried outwith an in situ reaction cell. Additional reactor measurements were performed on a more Sn-rich catalyst and on a pure Pd catalyst. Varying the temperature of reduction induced large variations in catalytic performance toward ethyne-coupling reactions. These changes are understandable in terms of the destruction of SnO2-like structures surrounding the Pd core, yielding a skin of metallic Sn which subsequently undergoes intermixing with Pd. The overall thermal and catalytic behavior of these highly dispersed materials accords well with the analogous single-crystal model system.

Ensemble effects in the coupling of acetylene to benzene on a bimetallic surface: A study with Pd{111}/Au

Acetylene coupling to benzene on the Pd(lll) surface is greatly enhanced by the presence of catalytically inert Au atoms. LEED and Auger spectroscopy show that progressive annealing of Au overlayers on Pd(lll) leads to the formation of a series of random surface alloys with continuously varying composition. Cyclization activity is a strong function of surface composition-the most efficient catalyst corresponds to a surface of composition similar to 85% Pd. CO TPD and HREELS data show that acetylene cyclization activity is not correlated with the availability of singleton Pd atoms, nor just with the presence of 3-fold pure Pd sites-the preferred chemisorption site for C2H2 on Pd{111}. The data can be quantitatively rationalized in terms of a simple model in which catalytic activity is dominated by Pd6Au and Pd-7 surface ensembles, allowance being made for the known degree to which pure Pd{111} decomposes the reactant and product molecules.

Aqueous phase reforming of xylitol over Pt-Re bimetallic catalyst: Effect of the Re addition

The aqueous phase reforming (APR) of xylitol was studied in a continuous fixed bed reactor over three catalysts: Pt/Al2O3, Pt/TiO2 and Pt-Re/TiO2. The data obtained in the case of the monometallic Pt catalysts was compared to the bimetallic Pt-Re sample. The effect of Re addition on the catalyst stability, activity, product formation and selectivity toward hydrogen and alkanes was studied. The bimetallic catalyst demonstrated a higher selectivity to alkanes compared to the monometallic samples. The monometallic catalyst was more selective toward hydrogen formation. A plausible reaction scheme explaining differences in selectivity toward hydrogen and alkanes was proposed and discussed.

Development of a PtSn bimetallic catalyst for direct fuel cells using bio-butanol fuel

Pt and PtSn catalysts were studied for n-butanol electro-oxidation at various temperatures. PtSn showed a higher activity towards butanol electro-oxidation compared to Pt in acidic media. The onset potential for n-butanol oxidation on PtSn is ~520 mV lower than that found on Pt, and significantly lower activation energy was found for PtSn compared with that for Pt.

A bimetallic catalyst on a dual component support for low temperature total methane oxidation

Palladium, platinum bimetallic catalysts supported on η-Al₂O₃, ZSM-5(23) and ZSM-5(80), with and without the addition of TiO₂, were prepared and used for low temperature total methane oxidation (TMO). The catalysts were tested under reaction temperatures of 200-500 °C with a GHSV of 100,000 mL g^-1 h^-1. It was found that all four components, palladium, platinum, an acidic support and oxygen carrier were needed to achieve a highly active and stable catalyst. The optimum support being 17.5% TiO₂ on ZSM-5(80) where the T_10% was observed at only 200 °C. On addition of platinum, longer time on stream experiments showed no decrease in the catalyst activity over 50 h at 250 °C.

Proteomic method for the quantification of methionine sulfoxide

Glycoxidation and lipoxidation reactions contribute to the chemical modification of proteins during the Maillard reaction. Reactive oxygen species, produced during the oxidation of sugars and lipids in these processes, irreversibly oxidize proteins. Methionine is particularly susceptible to oxidation, yielding the oxidation product methionine sulfoxide (MetSO). Here we describe a method for the analysis of MetSO using proteomic techniques. Using these techniques, we measured MetSO formation on the model protein RNase during aerobic incubations with glucose and arachidonate. We also evaluated the susceptibility of MetSO to reduction by NaBH4, a commonly used reductant in the analysis of Maillard reaction products.

Insight into the key aspects of the regeneration process in the NOx storage reduction (NSR) reaction probed using fast transient kinetics coupled with isotopically labelled (NO)-N-15 over Pt and Rh-containing Ba/Al2O3 catalysts

For the first time, the coupling of fast transient kinetic switching and the use of an isotopically labelled reactant (15NO) has allowed detailed analysis of the evolution of all the products and reactants involved in the regeneration of a NOx storage reduction (NSR) material. Using realistic regeneration times (ca. 1 s) for Pt, Rh and Pt/Rh-containing Ba/Al2O3 catalysts we have revealed an unexpected double peak in the evolution of nitrogen. The first peak occurred immediately on switching from lean to rich conditions, while the second peak started at the point at which the gases switched from rich to lean. The first evolution of nitrogen occurs as a result of the fast reaction between H2 and/or CO and NO on reduced Rh and/or Pt sites. The second N2 peak which occurs upon removal of the rich phase can be explained by reaction of stored ammonia with stored NOx, gas phase NOx or O2. The ammonia can be formed either by hydrolysis of isocyanates or by direct reaction of NO and H2.

The study highlights the importance of the relative rates of regeneration and storage in determining the overall performance of the catalysts. The performance of the monometallic 1.1%Rh/Ba/Al2O3 catalyst at 250 and 350 °C was found to be dependent on the rate of NOx storage, since the rate of regeneration was sufficient to remove the NOx stored in the lean phase. In contrast, for the monometallic 1.6%Pt/Ba/Al2O3 catalyst at 250 °C, the rate of regeneration was the determining factor with the result that the amount of NOx stored on the catalyst deteriorated from cycle to cycle until the amount of NOx stored in the lean phase matched the NOx reduced in the rich phase. On the basis of the ratio of exposed metal surface atoms to total Ba content, the monometallic 1.6%Pt/Ba/Al2O3 catalyst outperformed the Rh-containing catalysts at 250 and 350 °C even when CO was used as a reductant.

The investigation of mechanisms in environmental catalysis using time-resolved methods

The formation of nitrogen oxides (NOx) during a combustion process is difficult to avoid because of the large exotherm and the consequent problem of avoiding local high-temperature spikes. Consequently, for many applications, such as for automotive power generation, there will be a continuing need to use catalytic after-treatment to reduce harmful emissions. The investigation of the mechanisms of the key catalytic reactions in environmental catalysis can provide an insight into the action of the catalyst, and time-resolved methods offer a powerful means to study these processes under realistic conditions. The use of Temporal Analysis of Products (TAP) and Steady State Isotopic Transient Kinetic Analysis (SSITKA) methods to investigate the reduction of NOx under various experimental conditions is described. From a detailed analysis of the SSITKA profiles, it is shown that at low temperatures the mechanism for the formation of N-2 and N2O from NO may differ from the conventional high-temperature mechanism. This is supported by density functional theory calculations, which show that the barrier to the formation of N2O from the reaction of N(ads) and NO(ads) may be too high to allow this process to occur at low temperatures. The alternative reaction of NO(ads) + NO(ads) = N2O(g) + O(ads) is shown to be much more favorable and is consistent with the SSITKA analysis. The remarkable effect of hydrogen as a reductant at low temperatures is described, and alternative interpretations of the role of hydrogen are discussed.

A review of the selective reduction of NOx, with hydrocarbons under lean-burn conditions with non-zeolitic oxide and platinum group metal catalysts

Research on the selective reduction of NOx with hydrocarbons under lean-burn conditions using non-zeolitic oxides and platinum group metal (PGM) catalysts has been critically reviewed. Alumina and silver-promoted alumina catalysts have been described in detail with particular emphasis on an analysis of the various reaction mechanisms that have been put forward in the literature. The influence of the nature of the reducing agent, and the preparation and structure of the catalysts have also been discussed and rationalised for several other oxide systems. It is concluded for non-zeolitic oxides that species that are strongly adsorbed on the surface, such as nitrates/nitrites and acetates, could be key intermediates in the formation of various reduced and oxidised species of nitrogen, the further reaction of which leads eventually to the formation of molecular nitrogen. For the platinum group metal catalysts, the different mechanisms that have been proposed in the literature have been critically assessed. It is concluded that although there is indirect, mainly spectroscopic, evidence for various reaction intermediates on the catalyst surface, it is difficult to confirm that any of these are involved in a critical mechanistic step because of a lack of a direct quantitative correlation between infrared and kinetic measurements. A simple mechanism which involves the dissociation of NO on a reduced metal surface to give N(ads) and O(ads), with subsequent desorption of N-2 and N2O and removal of O(ads) by the reductant can explain many of the results with the platinum group metal catalysts, although an additional contribution from organo-nitro-type species may contribute to the overall NOx reduction activity with these catalysts.

Evaluation of Pt and Re oxidation state in a pressurized reactor: difference in reduction between gas and liquid phase

Determination of metal oxidation state under relevant working conditions is crucial to understand catalytic behaviour. The reduction behaviour of Pt and Re was evaluated simultaneously as a function of support and solvent in a pressurized reactor (autoclave). The bimetallic catalysts are used in selective hydrogenation of carboxylic acids and amides. Gas phase reduction reduced the metals more efficiently, in particular Pt.

Investigating the mechanism of the H 2-assisted selective catalytic reduction (SCR) of NOx with octane using fast cycling transient in situ DRIFTS-MS analysis

A mechanistic study of the H-2-assisted Selective Catalytic Reduction (SCR) of NOx with octane as reductant over a Ag/Al2O3 catalyst was carried out using a modified DRIFTS cell coupled to a mass spectrometer Using fast transient cycling switching of H-2 with a time resolution of a few seconds It was possible to differentiate potential reaction intermediates from other moieties that are clearly spectator species Using such a periodic operation mode effects were uncovered that are normally hidden in conventional transient studies which typically consist of a single transient In experiments based on a single transient addition of H-2 to or removal of H-2 from the SCR feed it was found that the changes in the concentrations of gaseous species (products and reactants) were not matched by changes at comparable timescales of the concentration of surface species observed by IR This observation indicates that the majority of sur face species observed by DRIFTS under steady-state reaction conditions are spectators In contrast under fast cycling experimental conditions It was found that a surface isocyanate species had a temporal response that matched that of N-15(2) This suggests that some of the isocyanate species observed by infrared spectroscopy could be important intermediates in the hydrogen-assisted SCR reaction although it is emphasised that this may be dependent on the way in which the infrared spectra are obtained It is concluded that the use of fast transient cycling switching techniques may provide useful mechanistic information under certain circumstances.

Long-range electronic coupling in bis(cyclometalated) ruthenium complexes

Symmetrical and unsymmetrical ligands containing terpyridyl coordinating units (N, N, N) or a cyclometalating equivalent (N, C, N), connected back-to-back either directly or via a p-terphenylene or 1,3-phenylene spacer, have been used to construct new diruthenium complexes. These compounds incorporate various terdentate chelates as capping ligands, to allow a double control of the electronic properties of each subcomplex and of the ensemble: via the terminal ligand or through the bridging fragment. Electronic coupling was studied from the intervalence transitions observed in several bimetallic ruthenium complexes of the bis-(cyclometalated) type differing by the substitution of a nitrogen atom by carbon in the terminal terpyridyl unit. The largest metal-metal interaction was found in complexes for which the terminal complexing unit is of the 1,3-di-2-pyridylbenzene type, i.e., with the carbon atom located on the metal-metal C-2 axis of the molecule. Investigations of the mechanism of interaction by extended Huckel calculations showed that the replacement of nitrogen by carbon raises the filled ligand levels, increasing the mixing with ligand orbitals and thus the metal-metal coupling. Finally, the intervalence transition was still observed for a bridging ligand containing three phenylene units as spacers, corresponding to a 24-Angstrom metal-metal distance.