Ruling out a massive asymptotic giant-branch star as the progenitor of supernova 2005cs

We calculate the predicted UBVRIJHK absolute magnitudes for models of supernova progenitors and apply the result to the case of supernova 2005cs. We agree with previous results that the initial mass of the star was low, around 6 to 8 M-circle dot. However, such stars are thought to go through a second dredge-up to become asymptotic giant branch (AGB) stars. We show that had this occurred to the progenitor of 2005cs it would have been observed in JHK pre-explosion images. The progenitor was not detected in these bands and therefore we conclude that it was not an AGB star. Furthermore, if some AGB stars do produce supernovae they will have a clear signature in pre-explosion near-infrared images. Electron-capture supernovae are thought to occur in AGB stars, hence the implication is that 2005cs was not an electron-capture supernova but was the collapse of an iron core.

NE-LIKE GE SLAB TARGET STUDIES CARRIED OUT AT RAL

The effect of non-uniform target illumination on the soft X-ray lasing output intensity of the J=2-1 Ne-like Ge transitions as a function of length was investigated. As the degree of nonunifonnity increased with length the Ne-like Ge 23.2 and 23.6 nm J=2-1 transitions did not show exponentiation of output intensity. Using an experimentally measured gain-intensity scaling relationship these results were modelled and good qualitative agreement obtained. The model indicates that for Ge targets which are non-uniformly illuminated, even with peak to valley ratios of up to 3 efficient operation can be achieved at between 2-3x threshold intensity. Further studies of the effect of increasing the separation between the two targets of a double target geometry are also presented.

Constructing a global understanding of the social ecology of leaving out of home care

Engagement with globalisation is growing in the field of youth transitions from out of home care. This includes cross national exchange of research, policy and practise, regional advocacy networking and global policy development. Furthering this emerging international child welfare perspective requires extending it to countries in the developing world and building conceptual frameworks which encompass a social ecology of care leaving, including its global dimension, the latter needs to address not only the needs, expectations and rights of care leavers but also the theories of change underpinning service design and delivery. Such a model is presented combining resilience and social capital as personal assets situated within a social ecology of support. To illustrate how this provides a means to help engage with the experience of countries where there appears to be very little information available on care leaving, a small scale South African initiative is considered. SA-YES is a youth mentoring project for young people leaving a variety of out of home placements. Planned as a three-year pilot, initial results are encouraging but require more rigorous evaluation focusing on program process and outcomes, quality of interpersonal relationships and synchronisation with cultural expectations and policy environment.

Pull-out behaviour of axially loaded basalt fibre reinforced polymer (BFRP) rods bonded parallel to the grain of glulam elements

Synopsis: Bonded-in rod timber joints off er several advantages over conventional types of joint, including high local force transfer, very stiff connections, and improved ?re and aesthetic properties since the connection is completely hidden in the insulating timber members. More recently, the use of ?bre reinforced polymer (FRP) as a connecting rod, alternative to steel rods, in bonded-in rod connections for timber structures has been investigated. However, the investigation into the behaviour of such joints is limited, in particular, connections involving basalt ?bre reinforced polymers (BFRP) bars - which is the primary focus of this research. This paper presents an experimental programme conducted to investigate the behaviour of bonded-in BFRP bars loaded parallel to the grain of glulam members. Tensile pull-out tests were conducted to examine the effect of bonded length and bond stress-slip on the structural capacity of the connection. An analytical design expression for predicting pull-out capacity is proposed and the results have been compared with some established design equations. It was found that pull-out load increased approximately linearly with the bonded length, up to maximum which occurred at a bonded length of 15 times the hole diameter, and did not increase beyond this bonded length. The most signi?cant failure modes were failure at the timber/adhesive interface followed by pullout of the BFRP rod. Increased bonded lengths resulted in higher bond slip values compared to lower equivalent bonded lengths. The proposed design model gave the best predictions of pull-out capacity compared with other existing models.

Undecaprenyl phosphate recycling comes out of age

The recycling of the lipid carrier undecaprenyl-phosphate (Und-P) requires the dephosphorylation of Und-PP, a reaction proposed to occur at the external or periplasmic side of the bacterial cell membrane. In this issue of Molecular Microbiology, experiments based on the analysis of lipopolysaccharide modifications in Escherichia coli demonstrate that the phosphorylation of lipid A at position 1 is catalysed by the membrane enzyme LpxT (formerly YeiU). This enzyme specifically transfers the distal phosphate group from Und-PP to lipid A 1-phosphate to produce lipid A 1-diphosphate. Furthermore, this reaction requires a functionally intact MsbA protein, which catalyses the transfer of lipid A across the membrane, confirming that the LpxT-mediated lipid A modification occurs on the periplasmic side of the membrane. These observations provide a novel and unexpected link between periplasmic lipid A modifications and the Und-PP recycling pathway.

The technical merits of turbogenerating shown through the design, validation and implementation of a 1 dimensional engine model

Turbocompounding is the process of recovering a proportion of an engine’s fuel energy that would otherwise be lost in the exhaust process and adding it to the output power. This was first seen in the 1930s and is carried out by coupling an exhaust gas turbine to the crankshaft of a reciprocating engine. It has since been recognised that coupling the power turbine to an electrical generator instead of the crankshaft has the potential to reduce the fuel consumption further with the added flexibility of being able to decide how this recovered energy is used. The electricity generated can be used in automotive applications to assist the crankshaft using a flywheel motor generator or to power ancillaries that would otherwise have run off the crankshaft. In the case of stationary power plants, it can assist the electrical power output. Decoupling the power turbine from the crankshaft and coupling it to a generator allows the power electronics to control the turbine speed independently in order to optimise the specific fuel consumption for different engine operating conditions. This method of energy recapture is termed ‘turbogenerating’.

This paper gives a brief history of turbocompounding and its thermodynamic merits. It then moves on to give an account of the validation of a turbogenerated engine model. The model is then used to investigate what needs to be done to an engine when a turbogenerator is installed. The engine being modelled is used for stationary power generation and is fuelled by an induced biogas with a small portion of palm oil being injected into the cylinder to initiate combustion by compression ignition. From these investigations, optimum settings were found that result in a 10.90% improvement in overall efficiency. These savings relate to the same engine without a turbogenerator installed operating with fixed fuelling.

Podcast of the launch of Trickle Out Africa project at British Council Nairobi

Film of the launch of the Trickle Out Project and speaches