Strength model for end cover separation failure in RC beams strengthened with near-surface mounted (NSM) FRP strips

As an alternative to externally bonded FRP reinforcement, near-surface mounted (NSM) FRP reinforcement can be used to effectively improve the flexural performance of RC beams. In such FRP strengthened RC beams, end cover separation failure is one of the common failure modes. This failuremode involves the detachment of the NSM FRP reinforcement together with the concrete cover along the level of the tension steel reinforcement. This paper presents a new strength model for end cover separation failure in RC beams strengthened in flexure with NSM FRP strips (i.e. rectangular FRP bars with asectional height-to-thickness ratio not less than 5), which was formulated on the basis of extensive numerical results from a parametric study undertaken using an efficient finite element approach. The proposed strength model consists of an approximate equation for the debonding strain of the FRP reinforcement at the critical cracked section and a conventional section analysis to relate this debondingstrain to the moment acting on the same section (i.e. the debonding strain). Once the debonding strain is known, the load level at end cover separation of an FRP-strengthened RC beam can be easily determined for a given load distribution. Predictions from the proposed strength model are compared with those of two existing strength models of the same type and available test results, which shows that the proposed strength model is in close agreement with test results and is far more accurate than the existing strength models.

Mitigation of concrete cover separation in frpstrengthened RC beams using FRP U-jackets

Concrete cover separation is a common failure mode of reinforced concrete (RC) beams strengthened with a fibre-reinforced polymer (FRP) plate bonded to the tension face (FRP-plated RC beams). Plate-end FRP U-jackets have previously been explored as a mitigation measure to delay or suppress concrete cover separation, although its effectiveness needs further clarification. The paper presents the first systemic experimental study on the use of FRP U-jackets of different forms for mitigating the concrete cover separation failure. A total of ten full-scale FRP-plated RC beams were tested. The test results show that both the ultimate load and the ductility of the beams were enhanced by the U-jackets. Among the forms of U-jackets explored, those inclined at 45o are the most effective.

Analytical model for bar-end cover separation failure in RC beams strengthened with near-surface mounted FRP

The flexural performance of RC beams can be improved using the near-surface mounted (NSM) FRP strengthening technique. A likely failure mode of such FRP-strengthened RC beams is bar-end cover separation which involves the detachment of the NSM FRP reinforcement together with the concrete cover along the level of the steel tension reinforcement. This paper presents a new analytical strength model for this failure mode. The proposed strength model and two existing strength models for this failure mode are compared with test results to demonstrate the superior performance of the new analytical model.

Sparse multi-carrier index keying OFDM with index separation over correlated sub-carriers

In this paper, we propose a sparse multi-carrier index keying (MCIK) method for orthogonal frequency division multiplexing (OFDM) system, which uses the indices of sparse sub-carriers to transmit the data, and improve the performance
of signal detection in highly correlated sub-carriers. Although a receiver is able to exploit a power gain with precoding in OFDM, the sensitivity of the signal detection is usually high as the orthogonality is not retained in highly dispersive
environments. To overcome this, we focus on developing the trade-off between the sparsity of the MCIK, correlation, and performances, analyzing the average probability of the error propagation imposed by incorrect index detection over highly correlated sub-carriers. In asymptotic cases, we are able to see how sparsity of MCIK should be designed in order to perform superior to the classical OFDM system. Based on this feature, sparse MCIK based OFDM is a better choice for low detection errors in highly correlated sub-carriers.

Novel monoclonal antibody and peptide binders for Mycobacterium avium subsp. paratuberculosis and their application for magnetic separation

The generation of novel Mycobacterium avium subsp. paratuberculosis (MAP)-specific monoclonal antibodies and phage-display derived peptide binders, along with their application for the magnetic separation (MS) of MAP cells, is described. Our aim was to achieve even greater MAP capture capability than is possible with peptide-mediated magnetic separation (PMS) using a 50:50 mix of biotinylated-aMp3 and biotinylated-aMptD peptide-coated beads. Gamma-irradiated whole MAP cells and ethanol extracted antigens (EEA) from these cells were used to elicit an immune response and as phage-display biopanning targets. A range of novel binders was obtained and coated onto paramagnetic beads, both individually and in various combinations, for MS evaluation. IS900 PCR was employed after MS to provide quick results. Capture sensitivity was assessed using a range of MAP concentrations after which the most promising beads were tested for their specificity for MAP, by performing MS followed by culture using 10 other Mycobacterium species. Magnetic beads coated with the biotinylated EEA402 peptide demonstrated a greater level of MAP capture than the current PMS method, even when low numbers of MAP (<10 cfu/ml) were present; however these beads also captured a range of other mycobacteria and so lacked capture specificity. Magnetic beads coated with monoclonal antibodies 6G11 and 15D10 (used as a 50:50 mix or as dually coated beads) also demonstrated improved MAP capture relative to the current PMS method, but with little cross-reactivity to other Mycobacterium spp. Therefore, two new MS protocols are suggested, the application of which would be dependent upon the required endpoint. Biotinylated EEA402-coated beads could potentially be used with a MAP-specific PCR to ensure detection specificity, while beads coated with 6G11 and 15D10 monoclonal antibodies could be used with culture or the phage amplification assay.

An aggregated fridge-freezer peak shaving and valley filling control strategy for enhanced grid operations

The need for fast response demand side participation (DSP) has never been greater due to increased wind power penetration. White domestic goods suppliers are currently developing a `smart' chip for a range of domestic appliances (e.g. refrigeration units, tumble dryers and storage heaters) to support the home as a DSP unit in future power systems. This paper presents an aggregated population-based model of a single compressor fridge-freezer. Two scenarios (i.e. energy efficiency class and size) for valley filling and peak shaving are examined to quantify and value DSP savings in 2020. The analysis shows potential peak reductions of 40 MW to 55 MW are achievable in the Single wholesale Electricity Market of Ireland (i.e. the test system), and valley demand increases of up to 30 MW. The study also shows the importance of the control strategy start time and the staggering of the devices to obtain the desired filling or shaving effect.

Deep separation of benzene from cyclohexane by liquid extraction using ionic liquids as the solvent

Separation of benzene and cyclohexane is one of the most important and difficult processes in the petrochemical industry, especially for low benzene concentration. In this work, three ionic liquids (ILs), [Bmim][BF ₄], [Bpy][BF ₄], and [Bmim][SCN], were investigated as the solvent in the extraction of benzene from cyclohexane. The corresponding ternary liquid-liquid equilibria (LLE) were experimentally determined at T = 298.15 K and atmospheric pressure. The LLE data were correlated with the nonrandom two-liquid model, and the parameters were fitted. The separation capabilities of the ILs were evaluated in terms of the benzene distribution coefficient and solvent selectivity. The effect of the IL structure on the separation was explained based on a well-founded physical model, COSMO-RS. Finally, the extraction processes were defined, and the operation parameters were analyzed. It shows that the ILs studied are suitable solvents for the extractive separation of benzene and cyclohexane, and their separation efficiency can be generally ranked as [Bmim][BF ₄] > [Bpy][BF ₄] > [Bmim][SCN]. The extraction process for a feed with 15 mol % benzene was optimized. High product purity (cyclohexane 0.997) and high recovery efficiency (cyclohexane 96.9% and benzene 98.1%) can be reached. © 2012 American Chemical Society.

Extent and mechanism of phase separation during the extrusion of calcium phosphate pastes

The aim of this study was to increase understanding of the mechanism and dominant drivers influencing phase separation during ram extrusion of calcium phosphate (CaP) paste for orthopaedic applications. The liquid content of extrudate was determined, and the flow of liquid and powder phases within the syringe barrel during extrusion were observed, subject to various extrusion parameters. Increasing the initial liquid-to-powder mass ratio, LPR, (0.4-0.45), plunger rate (5-20 mm/min), and tapering the barrel exit (45°-90°) significantly reduced the extent of phase separation. Phase separation values ranged from (6.22 ± 0.69 to 18.94 ± 0.69 %). However altering needle geometry had no significant effect on phase separation. From powder tracing and liquid content determination, static zones of powder and a non-uniform liquid distribution was observed within the barrel. Measurements of extrudate and paste LPR within the barrel indicated that extrudate LPR remained constant during extrusion, while LPR of paste within the barrel decreased steadily. These observations indicate the mechanism of phase separation was located within the syringe barrel. Therefore phase separation can be attributed to either; (1) the liquid being forced downstream by an increase in pore pressure as a result of powder consolidation due to the pressure exerted by the plunger or (2) the liquid being drawn from paste within the barrel, due to suction, driven by dilation of the solids matrix at the barrel exit. Differentiating between these two mechanisms is difficult; however results obtained suggest that suction is the dominant phase separation mechanism occurring during extrusion of CaP paste.

Porous organic cages for sulfur hexafluoride separation

A series of porous organic cages is examined for the selective adsorption of sulphur hexafluoride (SF6) over nitrogen. Despite lacking any metal sites, a porous cage, CC3, shows the highest SF6/N2 selectivity reported for any material at ambient temperature and pressure, which translates to real separations in a gas breakthrough column. The SF6 uptake of these materials is considerably higher than would be expected from the static pore structures. The location of SF6 within these materials is elucidated by x-ray crystallography, and it is shown that cooperative diffusion and structural rearrangements in these molecular crystals can rationalize their superior SF6/N2 selectivity.

Separation Science and Technology - Theory

I have completed 80% of a teaching text book (text and graphics) on Separation Science and Technology - Theory. The book's content is what I've learned over many years of practice and teaching with an emphasis on clarifying and explaining the nuances within the theories associated with various practical approaches to chemical and biochemical separations.

The book is divided into self-contained Chapters with many worked examples and practice questions. It very much aligns with my teaching on CHM3005D, CHM2010, CHM2007 and is ideal for PMY8105 and the new proposed MSci in Analytical Chemistry Programme. The book brings together diverse material in single space and will be a valuable pedagogical resource for the teaching of this key discipline within QUB and elsewhere.

Laterality as an indicator of emotional stress in ewes and lambs during a separation test

We assessed motor laterality in sheep to explore species-specific brain hemi-field dominance and how this could be affected by genetic or developmental factors. Further, we investigated whether directionality and strength of laterality could be linked to emotional stress in ewes and their lambs during partial separation. Forty-three ewes and their singleton lambs were scored on the (left/right) direction of turn in a y-maze to rejoin a conspecific (laterality test). Further, their behavioural response (i.e. time spent near the fence, vocalisations, and activity level) during forced separation by an open-mesh fence was assessed (separation test). Individual laterality was recorded for 44.2 % ewes (significant right bias) and 81.4 % lambs (equally biased to the left and the right). There was no significant association in side bias between dams and offspring. The Chi-squared test revealed a significant population bias for both groups (p < 0.05). Evolutionary adaptive strategies or stimuli-related visual laterality may provide explanation for this decision-making process. Absolute strength of laterality (irrespective of side) was high (Kolmogorov–Smirnov test, dams: D = 0.2; p < 0.001; lambs: D = 0.36, p < 0.0001). The Wilcoxon test showed that lateralised lambs and dams spent significantly more time near each other during separation than non-lateralised animals (p < 0.05), and that lateralised dams were also more active than non-lateralised ones. Arguably, the lateralised animals showed a greater attraction to their pair because they were more disturbed and thus required greater reassurance. The data show that measures of laterality offer a potential novel non-invasive indicator of separation stress.

Electron impact excitation of the Fe-peak ions Ni III and Ni IV

Accurate determination of electron excitation rates for the Fe-peak elements is complicated by the presence of an open 3d-shell in the description of the target ion, which can lead to hundreds of target state energy levels. Furthermore, the low energy scattering region is dominated by series of Rydberg resonances, which require a very fine energy mesh for their delineation. These problems have prompted the development of a suite of parallel R-matrix codes. In this work we report recent applications of these codes to the study of electron impact excitation of Ni III and Ni IV.

Investigating the Implications of a Variable RBE on Proton Dose Fractionation Across a Clinical Pencil Beam Scanned Spread-Out Bragg Peak

Purpose: To investigate the clinical implications of a variable relative biological effectiveness (RBE) on proton dose fractionation. Using acute exposures, the current clinical adoption of a generic, constant cell killing RBE has been shown to underestimate the effect of the sharp increase in linear energy transfer (LET) in the distal regions of the spread-out Bragg peak (SOBP). However, experimental data for the impact of dose fractionation in such scenarios are still limited.

Methods and Materials: Human fibroblasts (AG01522) at 4 key depth positions on a clinical SOBP of maximum energy 219.65 MeV were subjected to various fractionation regimens with an interfraction period of 24 hours at Proton Therapy Center in Prague, Czech Republic. Cell killing RBE variations were measured using standard clonogenic assays and were further validated using Monte Carlo simulations and parameterized using a linear quadratic formalism.

Results: Significant variations in the cell killing RBE for fractionated exposures along the proton dose profile were observed. RBE increased sharply toward the distal position, corresponding to a reduction in cell sparing effectiveness of fractionated proton exposures at higher LET. The effect was more pronounced at smaller doses per fraction. Experimental survival fractions were adequately predicted using a linear quadratic formalism assuming full repair between fractions. Data were also used to validate a parameterized variable RBE model based on linear α parameter response with LET that showed considerable deviations from clinically predicted isoeffective fractionation regimens.

Conclusions: The RBE-weighted absorbed dose calculated using the clinically adopted generic RBE of 1.1 significantly underestimates the biological effective dose from variable RBE, particularly in fractionation regimens with low doses per fraction. Coupled with an increase in effective range in fractionated exposures, our study provides an RBE dataset that can be used by the modeling community for the optimization of fractionated proton therapy.

The Exclusive Brethren ‘Doctrine of Separation’: An Anthropology of Theology

Why do the Exclusive Brethren attend church ten times a week? Why do they shun excommunicated members, including immediate family? Why do they refuse to eat with outsiders? Why will they employ outsiders in their businesses, but never be employed by them? Why do they reject modern media as “pipelines of filth”? Why do they refuse to vote, while simultaneously campaigning for Conservative Party candidates? Why do they only live in detached houses, and build churches entirely without windows? How, in other words, do the Exclusive Brethren try to live good lives? And what can we learn anthropologically from these models of ‘the good’, and from the objections they provoke? Drawing inspiration from Keane’s (2014) suggestion that ‘we shouldn’t decide in advance what ethics will look like’, this paper seeks to critically contribute to new scholarship within the anthropology of morality and detachment by constructing, in a very literal sense, an anthropology of theology via an analysis of the Exclusive Brethren ‘doctrine of separation’.